Open display units are one of the few built-in elements in a home that carry two jobs at once: they hold things, and they decide what a room looks like when you walk in. That double duty is exactly why buying them is harder than buying a freestanding shelf. A made-to-measure unit has to match the wall it sits against, the joinery around it, the lighting inside it and the objects going on it — all before a single panel is cut. This guide walks through what to check when you are specifying Santerson open display units, so the decision rests on drawings and confirmed details rather than on how good the render looks.
Start with the wall, not the shelf
Open display units usually get specified early in a project, when the wall behind them is still being decided. That sequence causes most of the rework. Before you look at layouts, fix three things on site: the finished wall line (including any plasterboard, panelling or stone build-up), the position of sockets and switches, and whether the wall can carry the load if the unit is fixed to it rather than standing freely.
For a recessed or floor-to-ceiling arrangement, take the width and height at three points along each dimension. Walls in older villas and renovated apartments are rarely square, and a single measurement will produce a unit that either needs packing out or leaves a visible shadow gap. Note the ceiling level too — sloped or stepped ceilings change both shelf heights and the way an upper section is scribed in.
Match the unit to what it will actually hold
The honest question to answer before choosing a layout is what is going on the shelves, at what weight, and how often you want to dust it. Books, ceramics, framed photographs and decorative objects all behave differently:
- Books and heavy objects need shorter shelf spans and deeper carcasses; long unsupported spans in a thin board will sag over time.
- Display pieces you want to see from a distance work better with wider spacing and fewer shelves, which is where open units beat glass-front cabinets.
- Objects you would rather keep out of reach of children or pets argue for mixing an open section with glass front display cabinets in the same composition.
- Items you change seasonally need adjustable shelf fixing rather than fixed shelves, so the spacing can be reset later.
This is where the Santerson configuration options matter. The open display units are listed as made-to-measure, with material and finish options and a layout tailored to the project, so the span, depth and shelf pattern should be set around your collection instead of you adapting the collection to a standard module.
Decide how much of the wall stays open
Fully open shelving looks light and reads well in a living room or study, but everything stored on it becomes visible, including the untidy things. Two practical ways to handle this without losing the open look:
- Split the composition. Keep an open section at eye level for what you want displayed, and put closed storage above and below. The open bookshelves range covers the tall, shelving-heavy version of this when the wall is doing a library role rather than a display role.
- Change the mounting. Where floor space is tight or the wall needs to stay clear, wall mounted display cabinets lift the storage off the floor and shorten the run of visible carcass.
- Consider a lit case for small, high-value pieces. An illuminated display cabinet does a similar job for a single object while protecting it and controlling how it is lit. Lighting specification and electrical details should be confirmed with the project's electrician before the carcass is fixed.
Check finish consistency across the whole joinery package
An open display unit rarely stands alone. It sits next to media units, sideboards, wardrobes or kitchen cabinetry, and the eye compares them instantly. Veneer tone, lacquer sheen and edge detailing look different on an open carcass than on a closed door, because more of the body is exposed — shelf edges, the inside faces of sides, and the back panel.
When you request finish options, ask for the same finish specified on the visible edges and interior surfaces, not only on the front. If the unit is being ordered alongside other built-ins from the same supplier, ask for them to be produced in one batch with the same material batch and finish schedule; this is one of the practical reasons project buyers work with a single one-stop furniture and building materials supplier rather than mixing sources across countries.
Confirm what is included in the quotation
Price differences between two made-to-measure quotations usually come from what is left out, not from the boards. Before you compare numbers, check that both quotations state:
- Overall dimensions and how the unit is scribed or packed to an out-of-square wall
- Carcass material, board thickness and the finish applied to edges and interior faces
- Shelf spans, shelf thickness and whether shelves are adjustable or fixed
- Any integrated lighting, transformers, wiring route and switching arrangement
- Packaging method, container or parcel arrangement, and who handles customs clearance on arrival
- Fixing method on site, and whether installation support is included or the unit is supplied for a local tradesperson to fit
For projects ordering from overseas, this is also where the supplier's service scope becomes relevant rather than promotional. SANTERSON describes a workflow that runs from design consultation and space planning through material selection, manufacturing and quality control, project management, logistics and final handover. As a turnkey furniture and building materials company, it handles these stages under one order rather than passing the buyer between workshops — see custom & OEM service for what can be changed on your side. Treat each stage as a line to confirm in writing for your own order: what is quoted, who is responsible, and at which stage.
Ask for the drawings before production starts
The single most useful checkpoint in a custom furniture order is the approved shop drawing. For open display units it should show elevation with every shelf height marked, plan section showing depth and how the unit meets the wall, material and finish call-outs, and the lighting position if light is built in. Sign nothing that does not show your finished floor and ceiling levels.
If you are working from a design package rather than measuring yourself, the supplier's design service can produce layouts and 3D visualisations, then coordinate drawings into production — described on the interior design services page. Either way, the drawing is what you compare against on delivery day.
Plan the delivery and installation window
Built-in units need a dry, finished room. Plastering, painting and flooring should be complete, and site access should allow the packaged panels in without damage. SANTERSON lists freight forwarding by sea, air and rail with customs paperwork and door-to-door delivery on its logistics page, and installation, inspection and after-sales support on the installation & after-sales support page. Confirm the arrangement for your specific order — delivery address, who receives the goods, and what happens if a panel is damaged in transit — rather than assuming any of it.
On arrival, check before signing: count packages against the packing list, inspect edges and corners for impact damage, and lay out the panels to confirm nothing is missing. Report damage on the delivery paperwork at that point, not afterwards.
A short pre-order checklist
- Three-point measurements of width, height and depth; ceiling and floor levels noted
- Written list of what the shelves must hold, with the heaviest item identified
- Decision on open versus glass-front versus lit display for each section
- Finish schedule covering edges, interior faces and back panel, matched to adjacent joinery
- Quotation checked against the inclusions list above
- Approved shop drawing signed before production begins
- Delivery date set against the site programme, with the room finished and dry
Work through those seven items and the decision stops being about whether a particular design looks good in a photograph. It becomes a specification you can compare, price and check on delivery — which is what an informed buying decision actually looks like for open display units from SANTERSON. To discuss dimensions, finishes and configuration for a specific wall, contact the team via the contact page.
Dimensions, materials, finishes and storage details vary with each configuration and should be confirmed for your project before ordering.