A wall hung basin looks simple on a drawing: one bowl, two brackets, a waste pipe. On site it is the opposite, because the carrier frame, the finished wall line, the waste outlet and the tap holes all have to agree before the first bag of adhesive is opened. This guide walks through how we plan delivery and installation for Wall Hung Basin 1038WB, Ceramic Wall Mounted Wash Basin for Bathroom, from the container arriving at port to handover of the finished powder room.
Why a wall hung basin needs earlier planning than a pedestal sink
The 1038WB is fixed to the wall through its back panel, so it takes no floor space and leaves the tile beneath it clear for mopping. That benefit also sets the constraint: the load path runs into the wall, not into the floor. The supporting frame and the solid or framed wall behind it must be built, set out and verified before the basin ever reaches the bathroom door.
For this reason we treat the basin as a first-fix item rather than a finishing item. Its rough-in dimensions travel with the shop drawings, not with the delivery note. If your project also specifies Wall Hung Toilet 1038W, Rimless Ceramic Wall Mounted WC for Modern Bathroom in the same bathroom, both units share one wall build-up and one inspection window, so they should be set out together by the same trade.
Before you order: confirmations that decide everything downstream
Send these points back to us in writing with your purchase order. Each one changes what is packed, and each one is cheap to fix on paper and expensive to fix on site.
- Quantity and split of delivery. Project orders are usually released in batches by floor, wing or room type, so the first container covers the mock-up rooms and the rest follow once the mock-up is signed off.
- Drainage arrangement. Confirm whether waste leaves through the wall or the floor, and confirm the trap and rough-in dimension against the technical sheet we supply for your order. Do not rely on a drawing taken from a catalogue image.
- Tap configuration and counter position. Deck-mounted, wall-mounted or basin-mounted taps each need their own setting-out, and the spout must clear the rim of the bowl once the finished tile thickness is added.
- Wall build-up. Tell us the finished face line after waterproofing, adhesive and tile, so the frame depth and the stud cavity are designed around it rather than adjusted later.
- Site conditions. Lift access, storage on floor, and whether rooms will be handed over locked and dry all affect how we pack and label cartons.
Where a project needs a different size, finish or tap-hole arrangement, our Custom & OEM Service covers bespoke specification and prototyping before series production starts.
Production, packing and how the goods are labelled
Each 1038WB is made from high-grade vitreous ceramic with a seamless glaze, then inspected and packed in a rigid carton with cushioning at the back panel and the rim, the two places most likely to take an impact in transit. For multi-room orders we label cartons by room or floor code rather than by pallet, so your installers can pick up exactly what one bathroom needs without opening the whole consignment.
Ceramics are heavy and brittle, so we keep them on their own dunnage layer in the container, away from joinery and lighting cartons. If you are consolidating Bathroom Sanitary Fixtures with flooring, wall panels or cabinetry in one shipment, tell us early: mixed containers are planned by unloading sequence at the site, not simply by weight.
Shipping and customs documents
Our Logistics & Door-to-Door Delivery service arranges sea, air or rail freight, packaging and container loading, shipment tracking and the paperwork your broker will ask for: commercial invoice, packing list and certificate of origin. For a wall hung basin order we recommend splitting the delivery into two consignments when the schedule is tight — frames and concealed hardware first so first-fix can begin, ceramic basins second so they spend the shortest possible time on site.
Tell your broker the material and use of each line item in advance. A description such as "ceramic wash basin" avoids the queries that a vague term like "bathroom parts" invites. Nominate one person on your side to receive shipment updates, and photograph every carton in the container at devanning: any damage claim rests on those images and on the count recorded the same day.
Site readiness checklist for the installation team
- Frame set out twice. Check the height of the finished rim line, the vertical position of the waste outlet and the depth of the finished wall face against the technical sheet for your order, then record the figures before the wall is closed.
- Wall substrate. The back panel bears on a solid, level surface. Confirm blocking or a structural board behind the fixing zone, and confirm that waterproofing has been applied and cured up to the required height.
- Waste tested open. Run water through the trap and inspection window before tiles go on. A leak found after tiling means removing finished work.
- Services complete. Supply lines, isolation valves and the waste connection should be pressure-tested and documented before the basin is hung.
- Clean, dry room. Basins are installed after wet trades finish and after the room can be locked. Dust and grit scratch glaze; an unlocked site is the most common cause of avoidable rework.
- Tapware on site. Confirm taps, waste fittings and seals have arrived before the fixing day, otherwise the basin sits unsecured while everyone waits.
Installation sequence in practice
The order below is the one we ask site teams to follow. Every step ends with a check, because a wall hung basin cannot be nudged into place at the last minute.
- Verify the delivery against the packing list on the day it arrives: carton count, room codes, and no hidden damage. Report any breakage immediately with photographs.
- Mock-up one bathroom first. Install a complete unit — frame, basin, taps, waste, tile surround — and have the client or consultant sign it off as the quality benchmark for the rest of the rooms.
- Set out and fix the carrier frame to the structural wall, checking rim height and outlet position against the technical sheet supplied with your order.
- Close the wall, tile, and let the wet work cure before unpacking any basin. Keep basins in their cartons, stored flat and indoors, until this point.
- Hang each basin on its back-panel fixings, connect waste and supplies, and check that the bowl sits level with no strain on the connectors.
- Fill and drain test every basin. Check for splash at normal flow, check the seal at the wall contact, and confirm the depth of the bowl contains spray as intended in daily use.
- Record each room with a photograph and a signed checklist. This becomes the handover pack and the baseline for any later warranty claim.
Handover, snagging and after-sales support
Our Installation & After-sales Support covers on-site installation guidance, inspection and snag lists, warranty coverage, spare parts and replacement. For a basin order the practical items to agree before we ship are which defects count as manufacturing issues, who signs off each room, and how replacements are handled — a single replacement basin for one hotel floor should not require a new container.
Give your site team the care notes with the goods as well: pH-neutral cleaners only, no abrasive pads, no acid-based descalers on the glaze or on chrome trim. Most "damaged basin" reports we receive trace back to cleaning practice rather than to the ceramic itself.
Common coordination failures and how to avoid them
- Rough-in confirmed from a catalogue image. Use the technical sheet issued with your order, and re-check it after the wall build-up is finalised.
- Basins delivered before first-fix starts. They then sit in corridors or lifts and get chipped. Sequence the second consignment to arrive when rooms are lockable.
- Wall hung ware set out by different trades. Basin and WC on one wall need one setting-out, one frame line and one inspection window.
- No mock-up room. Without a signed benchmark, every subsequent bathroom becomes a matter of opinion at handover.
Planning your basin order with SANTERSON
Tell us the room count, the drainage arrangement and the programme, and we will return a delivery split, packing plan and setting-out sheet you can issue to your site team. Whether you are fitting out a single villa bathroom or repeating one powder-room detail across a hotel floor, the sequence is the same: confirm the rough-in, protect the goods in transit, install after the wet work, and test every unit before handover.
Send your enquiry with drawings or a room schedule and we will quote Wall Hung Basin 1038WB, Ceramic Wall Mounted Wash Basin for Bathroom for your project quantity.