A flush interior door only looks right when the leaf, the frame and the surrounding wall read as one surface. That outcome is decided long before the first panel is machined: it is decided at the sample stage. If you are specifying Santerson Flush Interior Doors for a villa, apartment or hospitality fit-out, the finish sample review is the cheapest inspection you can run in the whole procurement cycle. Below is the sequence we use with project buyers and site teams to sign a sample off before production starts.

Why the sample matters more on a flush door than on a standard leaf

A conventional hinged internal door carries an architrave, so the eye accepts a small colour or sheen difference between leaf and skirting. A flush door is designed to sit level with the wall finish, which removes that visual escape route. Any mismatch in tone, grain direction or reflectance between the door face and the paneling beside it becomes obvious under site lighting. These doors are made to measure: sizing, layout, material and finish are specified per project rather than picked from a stock list, so there is no showroom unit to fall back on if the delivered colour is wrong. The approved sample becomes the reference for the entire order.

Request the sample set with the same specification sheet you will order against

Ask for the sample at the point you issue the door schedule, not after. Each sample should arrive tagged with the information that will also appear on your purchase order:

  • The collection it belongs to: flush interior doors, flush hinged, flush sliding, or the flush wall aligned type where the leaf is intended to disappear into a paneled wall.
  • Substrate and core construction as stated for the order, together with the face material: veneer, lacquer, laminate or paint system.
  • Finish build: number of coats, sheen level, and whether edges are finished to the same standard as the faces.
  • Colour or decor reference, including grain direction and any jointing pattern for veneered leaves.
  • Hardware positions shown on the sample where relevant, so you can see how the finish behaves around a hinge or handle route.

Keep one signed physical copy of that specification sheet with the sample. When goods arrive on site months later, the sample and the sheet are what you compare against, not a memory of an email thread.

Check the sample in the conditions where the doors will actually be hung

A sample reviewed under office lighting tells you very little. Take it to the room:

  • Hold the card vertically against the finished wall, at a similar distance from the window as the opening, and view it from the corridor approach rather than at arm's length.
  • Check it in daylight, under the fitting that will actually be installed, and after dark. High-gloss and metallic lacquer surfaces shift noticeably between those three states.
  • Compare the sample against the adjoining finishes: textured panels, wall panel systems, flooring and skirting. The flush detail puts them in direct contact.
  • Run your hand across the surface. Orange peel, dust nibs and an uneven satin break are visible under raking light long before they are visible straight on.

For a run of doors, ask for more than one leaf-face sample from the same batch if the finish is veneered or naturally figured. Two leaves can share a decor reference and still read differently once they are hung side by side.

Confirm the dimensions on the sample before you release production

Flush doors are only as good as the opening they sit in. Before signing off, verify with your site team that the door schedule behind the sample records:

  • Leaf size and the finished floor level the measurement was taken from, since a screed build-up changes the effective height.
  • Wall build-up and frame depth, so the leaf sits proud or recessed exactly as intended.
  • Which edges are visible. A concealed door that opens against a fixed panel needs a different edge treatment from a standalone leaf.
  • Threshold, floor spring or pivot decisions where the specification calls for them.

Where the design intent is a continuous wall, such as a door integrated into paneling or one of the decorative concealed designs, request the sample as part of the panel package rather than separately. Reviewing a door face without the matching panel sample is how a matched finish turns into a visible patch on a completed wall.

Sign the sample off in writing and record what you rejected

Return the approved sample with a dated sign-off naming the project, the door schedule reference and the reviewer. Keep the rejected samples as well. A rejected card with a short note beside it ("too warm under artificial light", "grain too open against the wall panel") settles a production conversation far faster than a written description in an email.

For buyers coordinating several trades, this is also the moment to check that the same finish reference has been approved for the joinery that meets the door: wardrobes, media walls and storage walls in the same corridor should be signed off against the same physical card, not separate printouts.

How a one-stop supplier changes the sample process

When doors, paneling, joinery and finishes come from several sources, each supplier sends its own reading of the same colour card and nobody owns the comparison. Santerson works as a one-stop furniture and building materials supplier, so the door leaf, the surrounding paneling and the fitted joinery can be sampled and approved inside one production programme, with the same team handling drawings, production coordination, door-to-door delivery and on-site installation guidance. On villa and hospitality projects that single chain of custody is what keeps a flush detail reading as one surface from the first site visit through to handover.

Materials, dimensions and finish options are confirmed per order, so treat any sample as valid only for the specification sheet it was issued against. If you are building out a door schedule for an upcoming project, send us the openings and the adjoining wall finishes and we will issue matching samples for review before production is committed.