A freestanding TV cabinet looks simple on a drawing: a low unit, a screen above it, some storage below. In an actual villa or apartment fit-out it sits at the centre of the longest sightline in the living room, and every other finish in that view — wall panelling, flooring, lighting, rug — is measured against it. When those items are specified one by one by different suppliers, the usual results are a cabinet that floats in front of a panel joint, a media wall whose veneer reads a different tone from the unit standing in front of it, and cables that were never routed anywhere. This article walks through how we coordinate Santerson freestanding TV cabinets with the surrounding products, in the order the decisions actually have to be made during a project.

Start With the Wall the Cabinet Will Stand Against

The most expensive mistake in a media wall is treating the cabinet as a piece of loose furniture and leaving the wall to the finishing trade. A freestanding unit is made-to-measure, so its width, depth and plinth can be set — but the panel layout behind it cannot be adjusted afterwards without cutting panels on site.

Before any panel order is released we settle three dimensions together: overall cabinet width, screen centre line, and the vertical joint pattern of the panelling. Where wood veneer panels or textured panels run behind the unit, we want a joint to land at the cabinet edge rather than in the middle of the visible span above it. That single check removes the impression that the furniture was dropped into a finished room.

Cabinet depth matters just as much for the wall build-up. A deeper unit leaves less room for a recessed screen niche, and a shallow unit in front of a thick cladding build-up makes the screen look like it is floating away from the wall. Depth and wall thickness are fixed at the same meeting, not in separate reviews.

Choose Between Freestanding and Fixed Media Systems Early

Santerson's media range splits into two families, and the choice between them changes what else has to be coordinated. A freestanding cabinet is a self-supporting piece; a fixed system becomes part of the wall.

SystemWhat it fixes for youWhat you still have to coordinate
Freestanding TV cabinetsLayout can change later; the unit can be re-sited or replaced without touching the wall.Wall joints, screen mounting height, cable exit points, floor covering under the plinth.
Wall-mounted media wallsStorage and screen support are carried by the wall, so the floor line stays clear.Substrate strength, fixing positions, concealed wiring routes before the wall is closed.
Full height media wallsOne continuous composition from floor to ceiling, with storage integrated.Ceiling junction, door and skirting interfaces, access panels for equipment.
Integrated TV panelsThe screen sits inside the panel field, so the wall reads as one surface.Panel rebate size, ventilation behind the screen, service access.
Sliding panel TV systemsThe screen can be closed off when the room is used for entertaining.Track position, panel overlap, clearance for the screen when it is exposed.
Floating TV unitsFloor covering runs continuously under the unit, which suits open-plan layouts.Load-rated substrate, hidden bracket positions, cable drops.

In practice we see freestanding cabinets chosen for two reasons: the client wants the flexibility to move the layout later, or the wall behind is already finished and cannot take fixings. Both are legitimate, and both mean the coordination work moves onto the floor and the wall surface rather than into the structure.

Match Finish and Material Across the Media Wall

A cabinet in one wood tone against panelling in another is the fastest way to make an expensive fit-out look assembled from catalogues. Our specification sequence is deliberately bottom-up:

  • Floor first. European oak herringbone engineered flooring and other plank formats set the warm tone in the room. We take the cabinet veneer or laminate from that reference rather than the reverse, because flooring is harder to change once laid.
  • Panelling second. Where the wall carries a contrasting material — stone-look, textured, or a darker veneer — we keep the cabinet in the family of the floor and let the wall carry the contrast. Two dominant materials competing behind one screen is where media walls start to look busy.
  • Cabinet third. Finish, door style and handle detail on the unit are set last, so they can echo either the floor or the wall as the room needs.

Sample size is a practical trap here. A 100 mm veneer swatch beside a flooring sample tells you almost nothing about how the two read across a three-metre wall under downlights. We ask for full-board or full-panel samples when a media wall is the main feature of a living room, and we view them in the actual room lighting before sign-off.

Where the project already has a fixed flooring or stone selection, send us that reference — sample, supplier code, or a photograph taken on site — and we build the cabinet finish around it instead of proposing something new.

Plan Lighting Around the Unit, Not After It

Lighting is the second coordination point that gets left too late. Recessed downlights aimed straight at a screen produce glare on the panel and make the picture unreadable in the evening; wall washers placed behind the cabinet throw hard shadows from the unit's edges.

For integrated schemes we specify media units with integrated LED lighting, or add integrated cabinet lighting to open niches and display shelves. Both approaches put the light source inside the joinery, which means the electrical feed, driver location and switching have to be decided while the carcass is still being drawn. A driver needs a serviceable position — behind an access panel, not sealed behind a fixed panel.

A backlit feature wall is the other option when the client wants the media composition to read as ambient light rather than fixtures. Here the coordination is with the screen rebate: the backlight field has to stop cleanly at the panel edge, and the heat and ventilation requirement behind the screen is confirmed before the panel is manufactured.

Storage Layout: Open Display Versus Closed Cabinets

The shelf configuration is a household decision, not an aesthetic one. Before drawing the carcass we ask what actually has to live in the unit — consoles and set-top boxes, games, board games, documents, barware, books — and how much of it should be visible.

  • Open and closed combo units are the default for family rooms: open shelves for equipment that needs ventilation and remote signal, closed compartments for everything else.
  • Glass front media units work where display matters but dust does — shelving for collections, glassware, or books beside the screen.
  • Storage and display combinations suit open-plan layouts where the media wall is also the room divider or the main storage run.
  • Where the living room needs a full storage wall, floating modular systems let the media unit share a composition with shelving and closed cabinets instead of standing alone.

Two details decide whether the storage works in daily use. Ventilated equipment compartments need louvres or rear cut-outs specified at manufacture, not drilled on site. And shelf spans carrying heavy items — a record collection, ceramics, a projector — are set with the correct substrate thickness so shelves do not deflect over time.

Cables, Screens and Services: What Has to Be Fixed Before Manufacture

This is where a well-drawn cabinet still fails on site if the sequence is wrong. Every item below has to be resolved before the carcass goes into production, because after that point the openings are fixed.

  • Screen size and VESA pattern — determines the panel rebate, mounting plate position and the load path in the wall.
  • Cable count and type — power, HDMI, optical, network, plus spare conduit for a future change.
  • Device stack location — whether equipment sits in the cabinet or in a separate rack; if it is in the cabinet, ventilation and remote signal are designed in.
  • Speaker positions — surface-mounted, in-wall, or in-cabinet, each needing a different allowance.
  • Switching and control — where the client will actually reach for power and lighting controls once the cabinet is in place.

For custom and OEM work we produce shop drawings with these openings dimensioned, and the client or their electrician signs them off before production. That single step is what separates a clean installation from a cabinet that arrives with the wrong cut-outs.

Soft Furnishings and the Rest of the Room

The media wall does not end at the cabinet. A decorative area rug in front of the unit anchors the seating group and, in an upper-level apartment, absorbs the footfall and speaker sound that a hard floor and a large panel would otherwise reflect. Rug size is set against the cabinet width, not the sofa: a rug that stops short of the unit makes the composition look top-heavy.

Seating distance is the other check worth making before furniture arrives. It follows from screen size and the room's depth, and it determines whether the cabinet can be shallow or needs to carry a deeper plinth for equipment. We would rather set that distance in the layout stage than have an installer trim a made-to-measure unit on site.

How the Coordination Runs on Our Side

Because Santerson supplies cabinetry, wall panelling, flooring, lighting and loose furnishings from one factory, coordination happens inside a single production plan rather than across several supplier drawings. The stages are the ones we run for every project:

  • Brief and layout. Room dimensions, screen choice, storage needs, and the finishes already fixed by the client or designer.
  • Specification and shop drawings. Dimensions, finish call-outs, openings for services, and hardware schedules issued for sign-off.
  • Production and inspection. Cabinet, panelling and related joinery produced to the same signed drawing set, so tones and edges match on delivery.
  • Packaging and freight. Crating, container loading and door-to-door delivery arranged with the rest of the project shipment rather than as separate consignments.
  • Installation and handover. On-site fitting, snag inspection, then spare parts and maintenance support afterwards.

Project-specific dimensions, materials, hardware and electrical details are confirmed on the drawings for each project. We do not publish fixed specifications for these configurable systems, because the correct answer depends on the room, the screen and the services already in the wall.

A Practical Checklist Before You Order

  • Cabinet width set against the panel joint pattern behind it.
  • Screen size, mounting height and rebate dimensions signed off before manufacture.
  • Cable routes, device location and ventilation confirmed on drawings.
  • Veneer or laminate sample viewed against the actual flooring sample in site lighting.
  • Lighting feeds and driver access positions resolved with the electrical plan.
  • Rug size and seating distance measured from the cabinet footprint.

If you are specifying a living room or media wall for a villa, apartment or hospitality project, send us the floor plan, your screen selection and any finishes already decided. We will come back with a cabinet layout, coordinated panel and finish schedule, and shop drawings showing every service opening before production starts.