A handleless concealed door only works when it disappears into the wall. On a drawing it looks simple: one flat leaf, no visible handle, a shadow gap instead of a frame. On site it can fail on details that never show up on a screen — where the grain runs, how the sheen reads under your lighting, whether the gap lines up with the panel beside it. That is why we ask buyers and project teams to approve a physical finish sample before Santerson Handleless Concealed Doors go into production.
These doors are made to measure, with material and finish selected for each space, so the sample stage is where a specification becomes something you can sign off. The steps below are the ones we use on villa, apartment and hospitality fit-outs, and they work just as well when you are sourcing joinery for several unit types at once.
What a finish sample has to prove
A sample is not a colour chip. For a concealed door it has to answer four practical questions, and each one asks something different of the sample itself.
- Colour and tone under your lighting. A matte lacquer that reads warm under a showroom lamp can read cool in a north-facing room or under LED downlights. Judge the sample in the room where the door is going, with the actual fitting switched on.
- Grain direction and pattern match. Veneered and wood-effect leaves have a grain that runs one way. Decide before production whether the leaf continues the surrounding wood veneer wall panels or deliberately contrasts with them, then check the sample shows the direction you agreed.
- Sheen and surface feel. Matte, satin and high-gloss surfaces behave differently along a long wall. Run your hand across the sample and view it from a low angle — that is how handling marks and an uneven finish become visible in daily use.
- Edge and gap detail. A concealed door depends on a clean edge and an even shadow gap. Ask for a finished edge, not just a flat face, so you can judge the line quality you will get on site.
Details to lock down before you request a sample
Sample reviews go wrong when the drawing is still open. Before we make a sample we confirm the items that change what the sample should look like:
- Opening sizes and leaf heights for each door type, taken from site measurement rather than setting-out drawings alone.
- Which openings are hinged and which slide. Concealed leaves and flush sliding doors sit in different wall build-ups, and the reveal detail differs accordingly.
- The finish system for each surface — lacquer, laminate, veneer, or a patterned leaf from the decorative concealed door range — and where it has to match cabinetry.
- Hardware intent. A handleless leaf is operated by an edge pull, a push mechanism or a routed reveal; the method you choose changes the edge profile you will be judging on the sample.
- Which rooms and unit types each approved finish applies to, so one sign-off covers a repeatable package instead of a single door.
If the same finish also appears on integrated door and paneling or on full-height storage walls, request that sample in the same round. Reviewing a door leaf next to the wall system it sits in is the only reliable way to confirm the two read as one surface.
A five-step review you can run with your client
We send samples labelled with the finish reference, the substrate and the batch, so approvals stay traceable across a multi-unit order. Then we work through this sequence:
- Light test in place. Fix the sample at the opening in the room where the door will be installed. Look at it in daylight and after dark with the artificial lighting on.
- Adjacent-material test. Hold the sample against the flooring, skirting and adjacent panelling. Tone clashes between a door leaf and a floor are far more obvious together than either material looks alone.
- Angle and distance test. Step back a few metres, then sight along the wall at eye level. This is where an uneven sheen or a mismatched grain shows up.
- Cleaning check. Wipe the sample with the method your maintenance team will actually use, let it dry and inspect it again. On hotel and rental work this protects the finish specification in the long run.
- Written sign-off. Record the finish reference, the rooms or unit types it applies to, the date and who approved it — and keep the physical sample. Photographs shift colour; the retained sample is what you compare production leaves against at delivery.
What usually surfaces at the sample stage
Three findings come up most often, and resolving them before panels are cut costs far less than the correction afterwards:
- The finish is right, the direction is wrong. A grain or texture that should run vertically has been sampled horizontally. Correct it on the sample, not on a production batch.
- Similar names, different result. Where door leaves come from one supplier and wall panelling from another, matching finish names do not guarantee a matching appearance. Sample both surfaces side by side and either accept the difference deliberately or change one specification.
- Too much sheen for the traffic. A glossier leaf than planned shows fingerprints on corridor and bathroom doors. Moving to a matte or satin system at sample stage is straightforward; changing it after production is not.
What we need from you to start
Send us the door schedule or your room list, the wall build-up each leaf will sit in, and the finishes it has to match. If the drawings are still developing, we can work with you on space planning and detailing first — see Interior Design Services — so the sample reflects a specification that can actually be built.
For villa and hospitality packages delivered through our turnkey project solutions, door leaves, panelling and built-in joinery are coordinated against a single finish schedule, which keeps sampling to one round wherever finishes repeat across units. Made-to-measure sizing and material and finish options are confirmed for each project before production, so the sample you approve and the doors you receive carry the same reference.
Share your drawings and we will prepare the samples for review.