A parquet floor rarely fails because somebody chose the wrong species. It fails because the drawing, the sample and the delivery arrived with three different ideas about what "European oak parquet" means. If you are an interior designer, a contractor or a developer's procurement lead, the alignment below is what we settle before a single board leaves the factory — and it is the same list we ask our own estimators to work through.

Start with the make-up of the board, not the colour

Parquet in this range is an engineered product: a lamella of solid European oak bonded to a multi-layer base. Two things on the specification sheet drive almost every downstream decision — the thickness of that solid oak lamella and the construction of the base beneath it.

The parquet boards we catalogue carry a 3 mm solid oak top layer over a multi-layer core. That thickness is what lets us saw-cut the lamella from European oak rather than peel it, so the grain runs through the wear surface and reads as solid timber underfoot. The cross-plied base is what holds the board flat when humidity swings between seasons, on site and in transit.

Ask your supplier to state these two items explicitly for the exact item you are buying, not for the range in general. Then check them against the physical sample you approved. When the sheet and the sample disagree, the sample wins — and that is worth resolving before purchase orders, not after.

Fix the pattern and geometry on the drawing

"Parquet" covers several different laying patterns with very different cutting losses. Herringbone and chevron consume more material and demand tighter setting-out than a straightforward plank format, and both behave visibly differently in a long, narrow room.

  • Confirm the pattern on the plan drawing, with the direction of the point indicated — herringbone laid toward a window reads very differently from herringbone laid across it.
  • Ask for the module size of the board you are specifying. A small lamella module and a large one change the rhythm of a room, and they change how square the subfloor has to be.
  • Have the same drawing show where borders run and where the field starts, so the cutting loss is agreed rather than discovered on installation day.

If your project calls for the geometric look specifically, our European Oak Herringbone Engineered Wood Flooring and Dark European Oak Herringbone Engineered Flooring pages show the formats we hold in the flooring range.

Agree tone and finish against an approved physical sample

Oak is a variable species, and that variability is the reason people specify it. The same cut can carry mineral streaks, sound knots and a wide spread of heartwood colour. Screen images cannot communicate any of that reliably — the only reference worth signing is a physical board with your project number on the back.

Within our parquet range the palette runs from pale, clean-grained boards to deep brown ones, so tone is a real specification choice rather than an afterthought. European Oak Parquet Engineered Hardwood Flooring in the light tone reads bright and quiet in a minimalist scheme; European Oak Parquet Engineered Wood Flooring in deep brown carries more contrast and weight. The wider Engineered Wood Flooring category covers both ends of that range.

Two practical habits save projects: approve a sample from the same production run you are buying, and state on the purchase order whether an approved sample governs the delivery. Where a batch sits outside the approved band, we would rather see it flagged in the factory than argued about on site.

Settle the substrate and installation method before ordering

An engineered parquet board is only as good as what it lands on. Adhesive fixing, floating installation and batten fixing each put different demands on flatness, moisture and floor height — and each changes how much preparation the site needs.

  • Agree who prepares the subfloor: the flooring supplier, the tiling or general contractor, or nobody by default. This gap causes more delays than product quality ever does.
  • Test and record substrate moisture before adhesive goes down, and keep the reading in the project file.
  • Confirm the finished floor level against doors, thresholds and stair nosings early — parquet plus adhesive plus underlay eats height quickly.

Adhesive and underlay are usually bought locally, which means compatibility sits with whoever supplies them. Ask your flooring supplier to confirm, in writing, which fixing methods a given board construction is intended for, and match that against the adhesive data sheet rather than installer habit.

Where underfloor heating enters the specification

The parquet boards in this range are described as compatible with underfloor heating, and multi-layer construction is exactly why engineered boards tolerate a warm slab better than a single thick piece of timber does. Compatibility, though, is not a performance promise on its own.

Get three things written down: the maximum surface temperature the board is intended to see, the ramp-up procedure for first commissioning of the heating, and whether the fixing method you chose is also approved for heated use. A system switched on at full output before the floor has acclimatised will cause trouble no product data sheet can undo.

Match the grade and format to the traffic it will actually carry

A villa living room, a hotel corridor and a show apartment are not the same duty. Grade selection decides how much character — knots, sapwood, grain variation — stays visible in the finished floor, and surface treatment decides how the floor takes abrasion and light over time.

Specification itemWho usually owns itWhere it gets recorded
Solid oak lamella thickness and board constructionSupplier, confirmed in writingProduct data sheet, purchase order
Laying pattern, module size and setting-out directionDesigner on the drawingFloor plan / setting-out drawing
Tone band, grade and surface finishDesigner approves physical sampleSigned sample record with batch reference
Substrate flatness, moisture and preparationSite contractorSite inspection record before installation
Fixing method, adhesive and underlay compatibilityInstaller plus local supplierMethod statement / installation instruction
Underfloor heating limits and commissioning sequenceMEP contractor with flooring supplierCommissioning plan, handover file
Quantities, spare boards and delivery phasingProcurement leadDelivery schedule against site programme

This table is a coordination checklist drawn from how we run flooring enquiries on villa and hospitality projects. Responsibilities vary by contract form — treat it as a starting agenda for the specification meeting, not a contractual allocation.

Order quantities and phasing like a site programme, not a shopping list

Parquet cutting loss depends on the pattern and on how square the rooms are, so an order quantity lifted straight off a net area drawing is usually short. Take the pattern into account, add a sensible allowance for cuts and breakages, and keep spare boards in store for later warranty or renovation work — a batch bought two years after installation may not match what went in.

For multi-unit projects, phase deliveries against the site programme rather than taking everything at once. Boards delivered early sit on a damp slab; boards delivered late stop the trade behind them. On our own project work we plan flooring alongside the joinery, doors and wall finishes as one package, because those four items share the same thresholds and levels.

Before you issue the purchase order — the short list

  • Board construction and solid oak lamella thickness stated for the exact item, not the range.
  • Pattern, module size and laying direction marked on a setting-out drawing.
  • A physical sample signed off, with batch reference recorded against the order.
  • Substrate moisture and flatness tested, with results in the project file.
  • Fixing method confirmed as suitable for that board construction — and for underfloor heating if there is any.
  • Quantities checked against pattern cutting loss, plus spares held in store.

SANTERSON has manufactured furniture and building materials since 2008, with flooring supplied as part of a wider package that covers cabinetry, doors, wall panelling, lighting and bathroom fixtures on villa and hospitality projects. If you send us the drawing, the room schedule and the sample you have approved, we will quote against that specification rather than against a catalogue line — contact us to start.