A metallic acrylic kitchen front looks decisive on a render and indecisive on site. Two projects can order the same colour name and end up with different reflections, different edge lines and different seams between tall units and wall cabinets. The difference is almost never the panel itself; it is the specification behind it. If you are specifying metallic acrylic cabinets for a villa or apartment kitchen, this guide sets out what to write down before the order goes into production, and what to ask your supplier to confirm back.

Why metallic finishes expose weak specifications

A solid colour hides variation. A metallic or pearl-effect surface does not: it reflects the light source, the room geometry and the direction of every door. That behaviour is what makes the finish attractive in a handleless kitchen, and it is also what turns a vague order into an expensive correction. Direction of the sheen, grain orientation across adjacent doors, the break line where one slab meets the next, and how the front reads under under-cabinet lighting are all decided on paper, long before the panel is cut.

Our Metallic Acrylic Cabinets sit inside the acrylic kitchen cabinet collection and are made to measure, with material, finish and layout specified per project. That flexibility is useful only if the specification carries the detail; otherwise a made-to-measure product simply reproduces an incomplete brief at full scale.

The six fields a metallic acrylic specification must contain

Write these six blocks into one document and treat it as the order reference. Anything you leave out will be decided by whoever is standing at the machine.

  • Reference and finish family. Product name, collection (acrylic kitchen cabinet), colour or effect reference, and whether the surface reads as metallic, pearl, high gloss or matte. Where a project mixes finishes, state which is which door by door.
  • Substrate and construction. The core board, its thickness, edge treatment and how the acrylic face wraps or caps the edge. Edge detail is where metallic fronts are most often judged after installation.
  • Direction of sheen and grain. State whether all doors in a run share one direction, and mark the drawing accordingly. This single line prevents the "two similar doors, different colours" complaint.
  • Dimensions and layout. Made-to-measure sizes for base units, wall units and tall or pantry units, with the wall and floor conditions they are measured against, not nominal catalogue modules.
  • Hardware and opening method. Hinges, soft-close, drawer slides, handles or push-to-open, load ratings for drawers, and integrated lighting where used. Hardware choice changes door thickness tolerances, so it belongs in the same document.
  • Scope of supply and site sequence. What ships together, how the run is packed and numbered, who installs, and what gets inspected before handover.

For kitchens supplied as part of a wider fit-out, the same six blocks work at unit level. Our custom built-in kitchen cabinets for hotel and apartment projects are specified the same way: layout, panel material, surface finish and matching hardware (hinges, drawer slides, support legs and brackets) listed together so one document governs the whole run.

Specification worksheet for project use

FieldWhat to recordConfirm back from supplier
Finish referenceColour/effect name, metallic or pearl effect, gloss levelPhysical sample of the same batch as production
Door directionMarked elevation showing sheen/grain direction per doorMarked-up drawing returned for signature
Panel buildCore board, thickness, acrylic face, edge treatmentCross-section sample of one finished door
SizesTaken-off dimensions per unit, wall and floor tolerancesShop drawing with final dimensions and clearances
HardwareHinges, slides, handles or push-to-open, load ratingBrand and model of each fitting, compatibility with door thickness
Lighting interfaceCabinet lighting position, cable route, control pointElectrical specification and cut-out detail per unit
Pack and sequenceUnit numbering matched to the room planPacking list keyed to the same numbers
Site conditionsDelivery access, storage, installation windowContainer loading plan and delivery scope for the project address

Where a product page lists an example dimension or an interface value, treat it as illustrative. Metallic acrylic fronts in this collection are specified per project, so dimensions, gloss level and hardware are confirmed against your own drawing before production.

Samples: the step most specifications skip

A colour chip on a screen is not a sample. For metallic acrylic fronts, request a physical panel off the production batch and judge it in three conditions: daylight from the room's main glazing, the ceiling scheme at night, and the under-cabinet or in-cabinet lighting once installed. Move the sample to the actual wall line and look at it from the standing position in the kitchen.

Then check the joinery detail on that same sample: how the face meets the edge, how a rebate or mitre reads at the corner, and how two panels sit side by side. If the project also uses other acrylic finishes: high gloss acrylic cabinets for a glossy contrast, or a matte acrylic front on tall units to reduce reflection. Place those samples next to the metallic one before you sign off. Finish combinations are decided at this stage, cheaply, or on site, expensively.

Layout details that decide how the finish performs

Metallic fronts reward clean geometry. Flat panels with concealed handles or touch-to-open keep the surface uninterrupted, which is why this finish pairs naturally with minimalist kitchen cabinets: flat panels, hidden handles and simple silhouettes give the sheen something orderly to reflect. Break that order with mixed module heights or an awkward filler panel and every imperfection becomes visible.

  • Runs of doors. Keep long door runs on one wall line where possible, and align door edges with the room's dominant sightline rather than with the ceiling grid.
  • Tall units and corner units. Specify L-shaped and U-shaped corner configurations, pantry and appliance housings in the same document, so door sizes are proportionate across the whole kitchen instead of adjusted on site.
  • Glass elements. Where a glazed display breaks the run, state whether it is framed or frameless and how the frame colour relates to the metallic fronts.
  • Integrated lighting. Lighting inside cabinets and along shadow gaps shapes how a metallic surface reads at night. Fix positions, cable routes and control points on the drawing, and confirm electrical ratings per unit.

What to send us, and what comes back

As a China-based furniture and building materials manufacturer working on villa, hospitality and apartment projects, we build metallic acrylic kitchens from your drawing rather than from a catalogue module. A workable enquiry carries the room plan with dimensions taken off site, the finish reference you have approved, the hardware preference, and the delivery address with access notes. If the layout is still open, our design service covers space planning, furniture layouts and 3D renderings before production starts.

In return you receive a shop drawing to sign, a physical sample of the specified finish, production with quality control at our facility, then freight by sea, air or rail with customs paperwork and door-to-door delivery. Installation, inspection of snags and after-sales support follow on site. Because cabinetry is usually one package among flooring, wall panels, wardrobes, lighting and bathroom fixtures, sourcing it through a one-stop furniture and building materials supplier keeps all of those items on one drawing set, one packing list and one point of contact.

Frequently asked questions

Can I order a single kitchen, or is there a minimum?

Single-project kitchens and bulk apartment or hotel orders are both handled. Order quantity, panel options and current production capacity for your project are confirmed when the drawing and finish reference are submitted.

How do I avoid colour variation between batches?

Order a complete run from one batch where the layout allows it, approve a physical sample of that batch before production, and split deliveries rather than splitting the order across separate productions. Mark door direction on the drawing so panels are cut consistently.

Does the metallic finish show fingerprints and marks?

Gloss level drives this more than colour does. High gloss surfaces show handling marks more readily than matte acrylic fronts, which is why many projects use a metallic effect on feature runs and a matte front on high-contact tall units. Decide the split at sample stage.

Can you match an existing kitchen's finish?

Send a physical sample of the existing front, with its substrate and thickness measured. We confirm what can be matched against available acrylic surfaces before quoting; an exact match is confirmed on a returned sample, not assumed.

To specify metallic acrylic cabinets for a residential or project kitchen, send your plan, the finish reference and the delivery location to SANTERSON. Phone / WhatsApp: +86 139 2821 4007 (PHILLIP), email: santerson@qq.com. Enquiries are answered within 24 hours, Monday to Saturday, 8:00 AM to 6:00 PM GMT+8. Full product range: SANTERSON products.