An L shaped corner cabinet is the one unit in a kitchen run that punishes poor planning. Two wall returns meet at a right angle, the carcass has to clear whatever sits on both sides, and everything stored inside sits behind a door and around a corner. When the unit is ordered from a drawing with the wrong dimensions or the wrong internal fitting, the error shows up later as a fridge that will not clear the corner, a door that fouls a handle, or a deep box that nobody can reach. A written installation plan is what stops that. Below is the checklist we work through on residential and project kitchens before an L Shaped Corner Cabinets order goes into production.
1. Verified site dimensions, not drawing dimensions
The plan starts with measurements taken on the finished room, after flooring, wall finishes, skirting and tiling are in place. Record the two run lengths from the corner to the face of each perpendicular unit, the available height to any overhead unit or hood, and the wall-to-wall angle at the corner. Walls are rarely square, and a 90-degree assumption carried into a made-to-measure order is where gaps and scribe lines appear on site.
Note obstructions that sit inside the corner zone: soil and waste pipes, boiler flues, radiators, switch plates, socket outlets, and any door or window reveal. Our units are supplied made-to-measure with material and finish options selected per project, so a cut-out for a pipe or a reduced carcass depth can be built in — but only if it is on the drawing before manufacturing starts.
2. The internal fitting, decided before the carcass is made
The corner is worth what its fitting makes it. Three approaches cover most layouts, and each one changes the door, the shelf heights and the neighbouring units:
- Rotating shelves. Lazy Susan Corner Cabinets bring the contents round to the opening. They suit base corners holding pots, small appliances and dry goods, and they need a clear, unobstructed door swing.
- Pull-out carousels and drawers. Pull Out Corner Cabinets track the stored items out of the corner, so nothing sits behind a shelf you have to lean into. Choose them where depth is generous and the load is heavy.
- Open shelving. An open-shelf corner reads lighter than a closed carcass and works well at the end of a run or beside a breakfast nook, where display matters more than concealment.
Whichever fitting is chosen, write it into the plan with the load it will carry. Heavy pans on a rotating shelf, a mixer on a pull-out tray, and light rarely used items on a high corner shelf all call for different shelf spacing and hardware.
3. Clearances, circulation and door swing
Draw the door arc on the plan. A hinged corner door needs room to open fully without hitting an island, a table edge or an appliance handle; a bi-fold or pocket arrangement saves that space at the cost of full access to one side. Then check the working aisle against whatever is opposite the corner: an oven door, a dishwasher door and a pulled-out drawer all occupy the same floor when in use.
Where the corner sits between tall units or next to an integrated appliance, confirm that the appliance door can open through its full angle with the corner carcass in place. This is a drawing-stage question, not a site-stage one.
4. Services, worktop and splashback coordination
A base corner frequently houses pipework, an electrical spur or both. Mark the position of water feeds, waste, gas and sockets on the plan so carcass backs can be prepared for them. If a sink is going into the corner, settle that decision early: it dictates the door type, the fitting above the bowl and where the tap lands relative to the worktop joint.
Then fix the worktop detail on paper. Decide where the mitre or joint falls along the two runs, how the edge returns to the wall, and how the splashback terminates at the corner. A corner cabinet ordered without a worktop drawing usually ends up with a joint that lands in the weakest, most used part of the bench.
5. Finish and specification matched to the rest of the run
The corner carcass should disappear into the kitchen it belongs to. Specify the door profile, finish and hardware from the same schedule as the straight units — handleless fronts, matte or high-gloss lacquer, wood veneer, shaker panels — so the corner does not read as an afterthought. Interior colour, edge treatment and shelf material belong on that same schedule, because open corners and glass-front corners expose all of it.
For a full-room scheme we specify cabinetry alongside the other joinery in the project, so the corner, the tall units and any Custom Built-in Kitchen Cabinets share one material and tolerance standard rather than three.
6. Sequencing, delivery and the installation order
Write the sequence into the plan: wall finishes complete, then the corner carcass set and levelled first because it sets the line for both runs, then adjacent units scribed to it, then worktop templating after the carcasses are fixed, then appliances and hardware. Corner-first sequencing is what keeps a long run straight.
For projects ordered from overseas this stage also needs the logistics recorded — container loading sequence, delivery date against the site programme, storage space on site for panels that cannot be installed on arrival, and who signs off the inspection. We handle door-to-door delivery and installation support as part of the project scope, so the plan should say which parts we cover and which the local contractor covers.
7. Tolerances, snag list and handover
State on the plan how the corner is meant to finish against an out-of-plumb wall: scribed panel, filler strip or a shadow gap agreed in advance. Then add the checks the installer signs off — door alignment and gaps equal on both legs of the corner, drawers and carousels running free with no rub, shelves seated at their agreed heights, worktop joint tight and sealed, and every fitting tested loaded.
A one-page snag list carried through that sign-off is what turns a completed installation into a documented handover, and it protects the project if an adjustment is needed later.
Before you order
If the plan answers seven questions — real dimensions, internal fitting, clearances, services and worktop detail, finish schedule, installation sequence, tolerance and snag sign-off — the corner cabinet stops being a risk. Send us the drawings for the run, tell us how the corner will be used, and we will confirm the carcass size, fitting and finish for it before production.