A sideboard rarely causes problems at the design stage. It causes them at quotation and handover, when nobody can agree on what was actually ordered. If you are specifying classic sideboards for a dining room, a villa living area or a hospitality project, the specification sheet is the document that decides whether the piece arrives as intended or becomes a variation order. Below is the structure we use to write one.

Start with the brief, not the drawing

Before any dimension is recorded, write down what the piece has to do in that room. A sideboard against a dining wall carries table linen, glassware and serving dishes. A sideboard in a villa entry handles keys, lighting and display objects. A piece in a hotel F&B back-of-house zone takes daily handling by staff. Those three jobs produce different internal layouts, different hardware and different surface requirements, even when the elevation looks identical on a drawing.

Our classic sideboards sit in the Dining Cabinets / Sideboards collection and are made for residential living projects, with finish, layout and dimensions specified per project. That means the brief you write is what we build from — there is no fixed catalogue size to fall back on.

The dimensional block: record numbers, not adjectives

Record the following as numbers, not adjectives:

  • Overall envelope — width, height and depth of the carcass, plus the projection of any cornice, plinth or countertop overhang.
  • Setting-out dimensions — distance from each finished wall face, the position of sockets, switches and service risers on that wall, and the depth of any skirting the piece has to scribe around.
  • Clearances — door swing arcs, drawer pull-out depth, and walkway width left in front of the unit once it is loaded.
  • Finished floor level — noted against a fixed point on site, because a sideboard that meets a stone countertop has to match the height of the surrounding worktops.

Where the sideboard is one element in a run of joinery, note which neighbouring units it has to align with. In our dark wood minimalist home project, the wall-mounted sideboard, its floating shelves and the kitchen cabinetry were designed as one continuous scheme — same panel tone, same shadow gaps — so each height had to be coordinated before production rather than corrected on site.

The layout block: draw the interior, not only the front

Draw the interior, not only the front. State how much of the unit is closed cupboard, how much is drawer, and how much is open display, then list what goes in each zone. A practical split we see work well in family dining rooms is heavy items low, everyday service items at waist height in drawers, and glassware or display pieces above the worktop line.

For adjustable shelving, give the pitch and the number of shelves supplied, and note whether shelf pins are visible or concealed. If wine bottles, decanters or a coffee machine belong on the top, say so in the specification — that is what drives rack details, load rating and a power point behind the unit.

Materials and finish: define what "classic" means

This is where "classic" needs to be defined. The term covers several distinct looks, and each one has different sampling and cost consequences:

  • Panelled doors — raised or recessed profiles, with the frame-to-panel ratio stated in millimetres.
  • Solid wood — species and cut specified, with an agreed board range for colour variation.
  • Veneer — grain direction, matching pattern and the sequence of leaves across the elevation.
  • Painted or lacquered — sheen level and a reference number, not a colour name.

Whatever route you take, request a physical sample of the exact finish before production is released. A rendered image cannot tell you how a lacquer behaves under warm accent lighting, or how a veneer grain reads across a two-metre elevation. Our custom and OEM service covers bespoke finishes, textures and prototyping, so samples are part of the normal process rather than an exception.

Hardware, lighting and services

List handles, knobs and pulls by type and fixing centres, and state whether hinge cups are visible or inset. For soft-close fittings, say which doors and which drawers carry them — specifying "all" when only the tall doors need it is a common way to inflate a budget.

If the piece has integrated lighting, record the fitting type, colour temperature, driver location and how the circuit is switched. Drivers fail, so they must sit in an accessible position, not behind a fixed panel. Where the countertop will host appliances, note the number and position of socket outlets and whether any cable management is required.

Verification before the specification is released

Close the specification with three confirmations. First, that the dimensions on the sheet have been checked against site conditions at the time of order, not taken from a drawing issued months earlier. Second, that the selected finish sample is signed off and referenced by code in the production file. Third, that storage, load and any electrical details are agreed for the final configuration.

For projects ordering several pieces together, group them with the rest of the fit-out so one coordination round covers everything. Sideboards sit naturally alongside buffet cabinets, tall dining units and kitchen cabinetry, and a single supplier handling the whole joinery package keeps finishes and lead times aligned. SANTERSON has operated as a furniture and building materials manufacturer in China since 2008, with design support, production, door-to-door logistics and installation coordination under one scope.

A short specification checklist

  • Envelope: overall width, height and depth plus every overhang, in millimetres
  • Setting-out: dimensions against finished wall faces and a fixed floor-level point
  • Clearances: door swing arcs, drawer pull-out depth and remaining walkway width
  • Interior: shelf pitch, shelf count and drawer configuration drawn out
  • Finish: material stated by reference code, with a signed physical sample
  • Hardware: type, fixing centres and the exact soft-close scope
  • Lighting: fitting, colour temperature, driver location and switching method
  • Services: socket outlet positions and appliance requirements behind the unit
  • Sign-off: site re-measurement confirmed at the point of order

Write those nine lines properly and the sideboard stops being a decorative afterthought. It becomes a documented item on your bill of quantities that anyone — buyer, factory, installer — can check against on the day the piece arrives.

Send us the room dimensions, the wall elevations and what you intend to store, and we will return a specification sheet for your review before anything goes into production. Contact our project team to start that process.