A kitchen quotation can look complete on paper and still fall apart on site. Panels arrive in the wrong size, handles are not what the drawing showed, and the hinge brand is decided by whoever packed the carton. A matte pvc cabinets buying checklist is the document that prevents this: it turns a good-looking render into an order you can actually receive, install and live with. Below is the checklist we work from on residential and apartment kitchens, room by room and line by line.

Why matte PVC doors need their own checklist

PVC-wrapped doors are a foil or film applied over a moulded substrate carrier, with the profile edges wrapped rather than edge-banded. That construction is what gives a shaker-style or arched door its soft, continuous surface, and it is also where quality differences hide. Two doors can share a colour name and differ in film thickness, carrier density, wrap adhesion and how the corners behave after a season of heat and steam.

A matte finish adds a second reason to be specific. Gloss reflects light, so it hides small surface irregularities; a matte or low-sheen surface shows them. Fingerprints, oily residue, and any orange-peel in the film become visible at an angle near a window. So the checklist for matte PVC doors has to cover the finish itself, not only the cabinet box behind it.

Part 1 — Scope: what is actually being bought

Before any material discussion, fix the boundary of the order. Most disputes start here, not at the factory.

  • Room list and quantity per room — kitchen only, or also laundry, pantry, butler's pantry and entertaining joinery.
  • Run lengths and heights in millimetres, taken from a finished-floor level, not a structural slab.
  • What is excluded: appliances, tapware, benchtops, splashback, plinth lighting, trade work.

Confirm which party supplies the benchtop and splashback, because the door edge detail and the scribe at the wall depend on that thickness. If you are furnishing a whole dwelling rather than one room, it is usually easier to keep cabinetry with the same supplier as interior fixtures and finishes, so one party answers for the junctions.

Part 2 — Door and drawer specification

Write this section as a table and make the supplier sign it. Every cell should have a value; blank cells become assumptions.

Line itemWhat to specifyWhy it matters for matte PVC
Door profileFlat slab, shaker, arched or moulded panel; radius of the returnThe moulded profile is what carries the wrap; a shallow return lifts at the edge over time
Carrier / substrateBoard type and grade for the door core and the cabinet boxDensity controls screw holding in the hinge zone and how the wrapped edge stays flat
Surface filmPVC film, colour or woodgrain reference, sheen bandColour names are not portable between factories; always work from a physical sample
Wrap detailFilm wrapped around all four edges; corner treatmentUnwrapped or poorly glued corners are the most common visible failure on PVC doors
Handle strategyProfile handle, recessed pull, touch-to-open, or surface handles and their fixing centresA handleless matte front reads as premium only when the reveal is straight and consistent
Door thickness and overhangPanel thickness, gap between doors, reveal at carcassMatte doors show uneven gaps far more clearly than gloss ones
Drawer frontsIntegrated front or overlay front, and matching grain direction across the stackWoodgrain PVC must run the same way on every drawer in a stack or the eye catches it

If you want a warm surface without real timber, wood grain pvc cabinet doors in the same PVC Kitchen Cabinet family are worth pricing alongside the matte solid colours. Ask for the grain direction and repeat pattern on the sample, because a large-format grain can look busy across a tall pantry.

Part 3 — Carcass, structure and fixing

  • Carcass board type, thickness and edge treatment on all visible edges.
  • Carcass finish inside and out — matching interior laminate or a plain melamine decision, stated.
  • Back panel thickness and fixing method; whether the box is cam-locked, dowelled or glued.
  • Wall fixing method for your wall type, plus noggings or battens you must provide on site.
  • Levelling legs, plinth height and whether the plinth is scribed to a raking floor.
  • Filler and scribe pieces at ceiling, wall and returns — confirm these are included, not "on site".

For apartment and hotel work, ask for the cabinetry as custom built in kitchen cabinets supplied with matching hardware — hinges, drawer slides, support legs and connecting brackets from the same order. Mixed hardware across batches is a recurring source of delay when units are installed by different crews on different floors.

Part 4 — Hardware: the line most quotations leave vague

Hardware is where a low quotation quietly becomes an expensive one. Specify brand and model, or specify "equivalent to be approved in writing" and hold the supplier to it.

ItemSpecify exactly
HingesBrand, model, cup depth, opening angle, soft close or standard, overlay dimension, quantity per door
Drawer slidesSide or undermount, extension, load rating, soft close, full overlay front height
Tall unit fittingsPantry pull-outs, larder brackets, door-mounted racks and their weight limits
Corner solutionsLazy Susan, magic corner or pull-out carousel — and the exact carcass width it fits
Baskets and traysWire or coated basket size, load rating, whether they suit your internal clear width
Sinks and tapware cut-outsCut-out template supplied before the door and top order is released

Ask for a hardware schedule as a separate sheet: one row per fitting, with quantity. Then check it against your drawing before you sign. If you later add or remove a drawer bank, that schedule is what makes the price change legible instead of arguable.

Part 5 — Layout and ergonomics

The checklist is not only about materials. A matte PVC kitchen can be specified beautifully and still work badly.

  • Work triangle checked against appliance positions, including the fridge door swing and the dishwasher door when open.
  • Bench height and island height set to the people using it; document both numbers.
  • Base cabinet draw plan: deep drawers in the cooking zone, doors only where they earn their keep.
  • Tall pantry reach zones — daily-use items between hip and eye height.
  • Appliance list with model numbers, ventilation requirements and clearance to adjacent doors.
  • Internal fittings for cutlery, bottles and small appliances, sized to the actual drawer interiors.

If your plan is open to a living area, look at custom minimalist kitchen cabinets for the run that faces the room: flat panels, concealed handles and a matching tall-unit door schedule keep appliances and pantry clutter out of sight from the sofa.

Part 6 — Measurement, drawings and approval gates

Set three sign-off points in writing before production starts. Without them, a delay is always blamed on someone else.

  1. Site survey after finishes. Measure after tiling, plastering and screed are complete. Record out-of-plumb walls and out-of-level floors, because scribes and fillers are sized to those numbers.
  2. Approval drawings. Elevations with dimensions, door schedule referencing each profile and colour code, hardware schedule, appliance schedule, electrical and plumbing set-out. One revision round is normal; more means the brief was unclear.
  3. Signed sample pack. Door sample, carcass sample, edge sample, hinge and slide sample, plus a written note of which side of each door faces out. Keep the samples after delivery — they are your reference at handover.

Part 7 — Finish quality checks you can run yourself

When the sample doors arrive, put them in raking daylight near a window and look along the surface rather than at it. That is how a buyer sees what the owner will see.

  • Surface flat and free of orange-peel; no telegraphing through the film.
  • Corners wrapped tightly, with no lifting, whitening or visible glue line.
  • Colour consistent between sample doors from different batches.
  • Woodgrain direction and pattern match across a stack of drawer fronts.
  • Sheen level matches the approved sample, not just the description "matte".
  • Wipe test with a mild detergent: no staining, no dulling, no swelling at the edges.
  • Hinge cup drilled cleanly, with no chipping of the wrap around the fixing points.

Ask how the surface is to be cleaned and keep that instruction. Matte films often mark if scrubbed with abrasive pads or strong solvents, and a cleaning mistake on site is not covered by any warranty discussion afterwards.

Part 8 — Packing, delivery and installation

  • Packing standard: edge protection, corner protectors, carton marking matched to the drawing labels.
  • Delivery address, access, lift dimensions or ground-floor drop; who carries it inside.
  • Consolidation with other fit-out items in the same shipment — flooring, doors, joinery and lighting are easier to reconcile on site when they arrive together.
  • Who installs: your cabinet maker or a supervised crew, and who signs off the snags.
  • Spares policy: replacement door panels, extra hinges and slides held back for later maintenance.

If the kitchen is part of a larger renovation or a multi-unit job, furniture logistics and door-to-door delivery with your own customs broker named in advance keeps the release of goods from stalling while the trades wait. Fix the delivery window against the plasterer's and tiler's dates, not the other way round.

Part 9 — Commercial terms worth pinning down

TermWhat a clear answer looks like
Quotation basisPriced per unit with the drawing revision number stated on the quote
InclusionsScribes, fillers, plinth, toe kick, internal fittings itemised or explicitly excluded
Payment stagesDeposit, release on approved drawings, balance before dispatch — each tied to a milestone you can verify
Change ordersWritten price and lead-time impact for any change after drawing approval
Lead timeFrom signed drawings and deposit, stated in working days, with the pre-production sample included or not
WarrantyWhat is covered on doors, carcass and hardware; what excludes it, including site cleaning and moisture exposure
Claims windowHow quickly damage or shortage must be reported after delivery, and in what form (photos plus carton label)

Part 10 — One-page checklist to paste into your enquiry

  • Room list, run lengths, heights, and the exclusions I am working to.
  • Door profile, carrier board, film type, colour or grain reference, sheen band, wrap detail.
  • Handle strategy and fixing centres; reveal and door gap dimensions.
  • Carcass board, thickness, edge treatment, interior finish, back panel, fixing method.
  • Hardware schedule by brand and model with quantities.
  • Appliance schedule with model numbers and clearances.
  • Internal fittings sized to actual drawer interiors.
  • Site survey after finishes; approval drawings; signed physical sample pack.
  • Packing standard, delivery access, installation responsibility, snags sign-off.
  • Payment stages, change-order rule, lead time in working days, warranty and claims window.

Frequently asked questions

Are matte PVC doors suitable for a hot kitchen wall next to an oven?

Specify the position and ask the supplier to confirm the door construction and finish for that location before production. Heat and steam exposure near ovens and cooktops is where wrap adhesion and film stability matter most, so get the answer in writing for the specific run rather than assuming a general rating.

Should I order doors and carcasses from one supplier or separate them?

One supplier is simpler for accountability at the junctions, but a mixed approach can work if the quotation states who supplies fillers, scribes and plinths, and who sets out the levels. The risk is not mixing suppliers — it is leaving the interface unowned.

How do I compare two quotations for the same kitchen?

Put both into the same table using the sections above. Differences usually appear in hardware brand, whether fillers and scribes are included, drawer count versus door count, and whether internal fittings are priced. Price per run is only comparable when those lines match.

Can I change colour after the drawings are approved?

You can, but treat it as a change order. Film batches differ, so ask for a new sample and confirm whether already-ordered carriers affect the lead time. Written confirmation of price and date before the factory stops the line protects both sides.

Where a single supplier helps

A kitchen rarely travels alone. Flooring, doors, wardrobes, wall panelling, lighting and bathroom fixtures all touch the same trades and the same site programme. Working with one furniture and building materials supplier for those packages means one drawing set, one hardware schedule and one party responsible when something arrives short. SANTERSON has been manufacturing furniture and building materials since 2008 and supports projects from design and custom/OEM production through to door-to-door delivery and installation support.

Send us your floor plan, the room list and the three numbers that matter most to you — budget band, completion date and which rooms must be finished first. We will come back with a specification sheet in the structure above, so you can compare our quotation against any other line for line.

SANTERSON — furniture and building materials manufacturer, custom/OEM kitchen cabinetry, interior fixtures and project fit-out. Enquiries: contact page.