Why two identical-looking quotes are not comparable

A quotation for light European oak engineered flooring rarely arrives in a form that makes comparison easy. One supplier writes “3mm wear layer, natural grade, 1900x190mm”. Another writes the same words with a different price. The difference between a good buy and an expensive mistake is usually buried in what the paper does not say. The checklist below follows the order a buyer actually works in — construction, surface, finish and colour, layout, then commercial terms — so that two proposals can be put side by side and defended to a client or a builder.

1. Read the construction before you read the price

Engineered flooring is a build-up, not a single piece of timber. The specification line that matters most is the thickness and species of the solid oak lamella on top, and what sits under it. Our Light European Oak Engineered Wood Flooring is built with a 3mm solid oak top layer over a multilayer base, and that cross-layered structure is the reason the board resists the cupping and edge-lifting that a single-piece board shows when room humidity swings.

When comparing proposals, ask each supplier to state three things separately: top-layer thickness, what the core layers are made of, and how the lamella is bonded to that core. Two boards can both claim a 3mm top layer and behave completely differently on site if one uses a cross-ply base and the other uses a laminated strip core. If a quotation gives only a total board thickness, treat it as incomplete.

Total thickness matters for the practical reason of transitions. Where engineered flooring meets tiled bathroom thresholds, an existing timber floor or a carpet edge, the difference between a 14mm and an 18mm board decides whether you need a reducer, a flat bar or a re-levelled screed. Get that dimension in writing before the layout is drawn.

2. Specify the surface, not just the species

“European oak” describes a tree, not an appearance. The same species can be supplied as a clean, cut-through board or as a character board full of knots, mineral streaks and open grain. For light tones this is the single biggest source of on-site disappointment: the sample on the desk was selected for its calm grain, while the containers arrive with a busier face.

Our light European oak planks keep natural knots and subtle grain deliberately — that is what produces the soft, rustic atmosphere buyers choose the product for — but a project specification should still record which character grade was approved. Write down whether live knots are accepted, whether sapwood and heartwood are both permitted in the mix, and whether colour is expected to be uniform or varied across the batch. Then attach the approved physical sample number to the purchase order.

Ask how the surface has been worked as well as how it has been coloured. Saw-cut and wire-brushed faces hold light differently from a planed face, and a brushed texture also collects more fine dust in high-traffic corridors. If the design intent is a matte, low-sheen floor that reads as natural timber rather than lacquered board, say so explicitly on the enquiry; suppliers will otherwise quote whatever finish they normally stock.

3. Match the finish to the traffic, and check what it protects

The finish is a wearing system with a service life, and it should be quoted as one. For a private residence, the question is whether the floor will see rolling chairs, pet claws and sandy entryways. For an apartment let by the owner or a short-stay rental, the question is how the floor looks after four turnover cycles rather than after four weeks.

Our light oak boards are finished with smoked antique craftsmanship, which gives the pale tone its depth instead of a flat, yellow-waxed look. Two practical points follow from that. First, a smoked or fumed surface is a colour treatment inside the timber, so it behaves differently from a surface stain if the top layer is ever sanded back — ask before treating any engineered board as renewable. Second, with a 3mm lamella you have far less margin for on-site re-sanding than with a thick solid board, so protectors on furniture legs, a doormat strategy at every entrance and felt under castors belong in the handover pack, not in an argument a year later.

4. Confirm colour against a real reference

Light European oak covers a wide band, from pale bleached boards to warm honey tones and smoked antique greys. A proposal that says only “natural oak” cannot be compared with one that says “light bleached”. Where the design requires a specific tone, request the reference code used in the factory and order physical boards, not printed brochures or screen visuals; photographically, a pale plank on a white page reads several shades warmer than it does over a dark wall.

If the project spans more than one delivery, ask how colour consistency between batches is handled and who signs off the second batch. This is where a single-supplier fit-out earns its keep: when the engineered wood flooring is ordered alongside cabinetry, wall panelling and joinery from the same factory, the oak tones in the floor and the timber used in the built-in units are matched once, at sample stage, instead of being reconciled by a subcontractor on site.

5. Check the layout format against the room

Plank width changes both cost and yield. A wide plank shows fewer joints and looks calmer in an open-plan living area, but it wastes more material in a narrow corridor with many doorways. Herringbone and parquet formats carry higher installation labour and demand a square setting-out line before the first row is laid.

If the design brief calls for patterned oak rather than straight planks, compare like for like across proposals. A European Oak Herringbone Engineered Wood Flooring in a light bleached tone and a European Oak Parquet Engineered Wood Flooring in a deep brown grain are priced on different material yields and different laying time, so a patterned quote should state the format dimensions, the bond pattern, the cutting allowance and the number of square metres actually covered — not just a rate per square metre.

Then check that the room can accept the pattern. Herringbone reads best in a room with long, uninterrupted sightlines; in a hallway full of doors it fragments. Ask the supplier for a setting-out drawing before ordering, and reconcile it with the door thresholds and the direction of sunlight.

6. Verify the substrate and installation terms

Most flooring failures are decided under the boards, not on top of them. A serious proposal states the acceptable moisture content of the screed, the primer and adhesive system being quoted, whether an underlay is included for a floating lay, and which fixing method applies to each room type. It also states who prepares the subfloor and what flatness tolerance is required, because a supplier blaming “site conditions” and a builder blaming “the product” leaves the client holding the cost of the lift-out.

If underfloor heating is present or planned, raise it in writing at quotation stage. Engineered multilayer boards are generally more tolerant of a heated screed than a single-piece board, but the adhesive system, the ramp-up schedule for first heating and the maximum surface temperature all need to be confirmed against the exact product being supplied rather than assumed from the category.

7. Read the commercial terms as carefully as the technical ones

For an imported order, the proposal should answer the boring questions clearly:

  • Is the price per square metre of covered floor or per square metre of boards shipped? The gap is the cutting allowance.
  • Are spares included, and in what percentage — and are they from the same production batch?
  • Which Incoterm applies, and who arranges freight, insurance and customs clearance at destination?
  • How are container quantities set, and what happens to a colour grade if a reorder falls outside the original batch?
  • What is inspected before dispatch, and what photographic or packing record comes with the shipment?

A supplier who works on whole projects tends to answer these without being chased, because the same team later handles the delivery and the snag list. SANTERSON supplies turnkey interior project solutions covering villas, hospitality and office fit-outs, with flooring coordinated alongside cabinetry, wall finishes, lighting and loose furniture under one production and logistics plan.

8. Red flags worth walking away from

  • A price that is far below the market with no explanation of the lamella thickness or core construction.
  • Wear-layer thickness quoted as “approximate”, or a total thickness given without breaking down the build-up.
  • No character-grade definition for a light oak, and no approved sample referenced on the order.
  • Adhesive, primer, trims and skirting excluded from the quote and then added as site variations.
  • No written position on subfloor moisture, flatness or underfloor heating compatibility.
  • Batch and reorder policy left vague, with spares promised verbally but not listed on the packing documentation.

How to compare the two proposals side by side

Put both quotations into the same table: construction, top-layer thickness, character grade, finish and sheen, colour reference, board format, covered area versus shipped area, spares, subfloor terms, heating terms, delivery terms and after-sales handling. Score each line as stated, partially stated or missing. A proposal with more empty cells is not cheaper — it has simply moved the cost to a later date.

If you are sourcing flooring as part of a wider fit-out, send the same floor specification to us together with the joinery and wall-panel drawings. We will confirm the oak tone and construction against the other timber elements in the project and return a single specification sheet you can compare line by line with any competing offer. Contact our project team with your plan dimensions, subfloor details and target programme, and we will quote the floor as part of the whole package or on its own.