A handleless kitchen looks simple on paper: flat doors, no protruding hardware, clean lines. That apparent simplicity is exactly why quotations go wrong. When a buyer sends nothing more than a rendering and the words "handleless European cabinets", the supplier has to guess at the opening method, the panel material, the carcass depth and the appliance schedule. Those guesses come back later as variation costs, delayed production and on-site fitting problems.
At SANTERSON we manufacture handleless European cabinets made to measure for villa, apartment and hospitality projects, together with the joinery, wardrobes, wall panelling and interior fixtures that surround them. The brief below is the same information list our estimators work from. Send it with your first enquiry and you will normally receive a usable quotation instead of a series of follow-up questions.
1. Drawings That Carry Dimensions, Not Just Intent
A mood board tells us the look you want. It does not tell us the room. For an accurate price we need plans and elevations with dimensions marked, ideally in millimetres, showing:
- Wall lengths, overall run of base and wall units, and the height available from finished floor to ceiling.
- Finished floor level and finished wall face. Cabinet heights are measured from the completed surface, so a 25 mm screed build-up changes the tall unit height.
- Positions of structural columns, beams and any bulkhead that a tall unit or wall unit has to stop against.
- Window reveals, sill heights and door swings that limit where a wall unit or an appliance housing can sit.
- Locations of soil stacks, waste runs, water supply points, the hot water system and the electrical board.
If measured drawings do not exist yet, send the architectural set and tell us which rooms are fixed and which are still being designed. Where a site survey is required, we can arrange site measurement before production begins, as part of the custom cabinetry workflow.
2. How the Doors Are Meant to Open
"Handleless" describes an appearance, not a mechanism. Two kitchens that look identical in a rendering can carry very different costs depending on how the fronts are opened and what has to be cut into them. Tell us which of these your design assumes:
| Opening method | What the supplier needs to know |
|---|---|
| Recessed channel or routed profile in the door edge | Profile style and depth, plus whether the finger recess runs along the top or bottom edge. This affects panel thickness and how adjacent doors meet at corners. |
| Aluminium or polymer rail profile on wall units and tall units | Rail colour and finish, and whether the rail is mitred at internal and external corners. Mitred corner rails take more work than straight runs. |
| Push-to-open hardware with no visible recess | Door weight and size per unit, because the mechanism is matched to door mass. Our handleless minimalist kitchen cabinets use touch-to-open fronts with soft-close fittings as standard configuration. |
| Integrated pull in a drawer front or recessed plinth | Drawer bank layout and the depth of the plinth setback, which sets the toe-kick clearance for the person working at the bench. |
Also state whether handleless detailing continues into other joinery in the same project. Concealed doors that sit flush with a wall panel are quoted separately from kitchen fronts, and the panel system has to be resolved together with the door if the joint line is meant to disappear.
3. Panel Material, Surface Finish and Edge Detail
Handleless fronts show every weak point in the edge treatment, because there is no handle boss hiding it. Specify the surface you want and we will confirm what is available for that format:
- Solid colour, matte or high gloss. Matte and handleless matte cabinets in acrylic, lacquer or melamine; gloss fronts need a matched edge band or wrap so the sheen reads continuously.
- Wood grain and veneer. Grain direction matters on tall slab doors. Tell us whether the grain runs vertically or horizontally, and whether adjacent panels should be book-matched.
- Two-tone schemes. Note which zones carry which colour so the carcass, internal boxes and plinth can be priced consistently.
- Edge detail. State the preferred edge radius or chamfer and whether a 2 mm ABS edge, a wrapped edge or a mitred solid core is expected. This is one of the most common causes of a re-quote.
Send colour references as a manufacturer code, a physical sample, or both. A photograph of a painted door will not hold a colour across screens and production batches. For our wood and taupe handleless kitchen cabinets, the specification on file pairs natural wood grain fronts with matte taupe flat doors, which is a useful model for how to describe a two-material scheme in words.
4. The Appliance Schedule and Wet-Area Positions
In a handleless kitchen the appliance housings set the rhythm of the elevation, so they cannot be decided after the cabinets are drawn. For every built-in appliance, send:
- Model number or the exact niche width, height and depth required, plus whether the door is an integrated panel or a visible stainless front.
- Ventilation route for ovens, refrigeration and cooktops, and where the extracted air discharges.
- Door hinge side and opening angle, which determines the minimum adjacent clearance and whether a deco panel or filler is needed.
- Power point position relative to the niche. A socket behind an oven cavity is a different job from one in the tall unit next door.
For the wet area, mark the sink bowl size and undermount or top-mount preference, mixer type, waste position and whether a dishwasher sits to the left or right. Benchtop material and thickness also matter: a stone top sets the load path for wall units above and changes how an undermounted hob is detailed.
5. Interior Configuration and Hardware
Storage layout
Carcass count alone understates a handleless kitchen, because most of the cost sits inside the boxes. Confirm:
- Drawer banks versus hinged doors with shelves, and the number of drawers per bank.
- Corner solutions — carousel, pull-out magic corner, or plain shelved corner — as these differ substantially in price.
- Tall pantry internals: pull-out larder frames, wire baskets, integrated lighting.
- Soft-close requirement on doors and runners, plus any handleless-specific push-open mechanism.
- Internal carcass finish colour and whether edges are exposed in open niches.
- Integrated lighting: under-wall-unit strips, in-cabinet sensors for glass-front display units, and where transformers may be accessed for maintenance.
Where the kitchen extends into a butler pantry, laundry or media wall, list those rooms in the same enquiry. Our custom built-in kitchen cabinets for hotel and apartment projects are usually quoted with matching hardware — hinges, drawer slides, support legs and connecting brackets — so consolidating the joinery scope in one enquiry keeps the specification consistent across rooms.
6. Project Context: Quantity, Programme and Delivery
A single villa and a forty-apartment fit-out need different documentation. Tell us:
| Item | Why it changes the quotation |
|---|---|
| Number of kitchens or repeat unit types | Repeat units allow one approved detail to be reused, which is where bulk pricing comes from. |
| Required site delivery month | Sets the production window and how long approval samples and shop drawings may take. |
| Delivery terms and destination | Port, city or site address determines freight mode. We arrange sea, air and rail forwarding with customs paperwork and door-to-door delivery. |
| Who installs on site | Determines how detailed the assembly drawings and packing sequence need to be. Installation support can be arranged for project work. |
| Other trades in scope | Flooring, wall panelling, doors, wardrobes and lighting supplied from one source are coordinated as one package rather than several separate orders. |
For Australian villa work we have delivered joinery and furnishing packages on projects in Willoughby, North Turramurra, Perth, Melbourne and Sydney. Import terms, duties and delivery scope are confirmed per project rather than assumed.
7. What the Supplier Should Return to You
A quotation worth comparing against a competitor's should contain more than one total figure. Ask for:
- An itemised price by room and unit type, with panel material and finish named in each line.
- A layout drawing or 3D rendering prepared from your brief, so you can check that the assumptions match your design.
- Hardware schedule stating hinge, runner and lift-up types, with make or grade identified.
- Explicit exclusions: stone tops, appliances, plumbing, electrical, tiling and on-site making-up.
- Lead time from approved shop drawings, plus packing list format and container loading plan.
- Warranty scope and spare parts arrangement in writing.
If two quotations differ by a wide margin, compare the hardware schedule, panel thickness and edge detail before comparing the totals. That is where most of the gap usually sits.
A Short Checklist to Paste Into Your Enquiry
Frequently Asked Questions
Can you quote from a rendering alone?
We can give an indicative range from a clear rendering plus room dimensions, but it is not a price to sign against. Panel material, opening method and internal configuration are the three variables that move the number most, and a rendering rarely resolves all three.
Do you make handleless fronts in high gloss as well as matte?
Yes. Both finishes are available in the European cabinet range, including handleless high gloss cabinets. Gloss fronts require a matched edge treatment, so we confirm the edge detail before quoting rather than substituting it during production.
Can the kitchen be ordered together with wardrobes and wall panelling?
Yes. Supplying cabinets, handleless concealed doors, wardrobes and panelling as one package keeps panel material, colour and joint detailing consistent from room to room, and reduces the number of separate approvals on site.
Is a site survey needed, or are my drawings enough?
Dimensioned drawings are usually sufficient to start. Where drawings do not exist or existing levels are uncertain, we can arrange site measurement before production begins, so the tall unit heights and appliance niches are taken from the completed floor and wall faces rather than from a plan assumption.
What if my drawings are still at concept stage?
Send what you have. Interior design support covers space planning, material selection and product specification, so a concept set can be developed into production drawings before manufacturing starts.
Send your drawings, appliance schedule and finish references to SANTERSON and we will return an itemised quotation with a layout drawing for review. Talk to our project team about handleless cabinetry for your villa, apartment or hospitality project.
Contact us · WhatsApp +86-13928214007 · santerson@qq.com