A wardrobe brief usually arrives as a mood board, a finish name and a room elevation. That is enough to start a conversation, but it is rarely enough for a factory to price Smoked Veneer Wardrobes correctly. The difference between a smooth run and an expensive rework is usually the quality of the enquiry itself. Below is the sequence our project team works through when a residential or villa scheme moves from concept drawings to made-to-measure joinery.

Smoked Veneer Wardrobes sit inside our Wood Veneer Wardrobes collection and are built for residential wardrobe projects. Finish, layout and dimensions are specified per project, so the enquiry stage is where the specification actually gets settled — not after production starts.

Start with what the brief already tells you

Before writing anything to a supplier, pull the fixed information out of your own drawings. Wardrobe joinery is constrained by the shell: floor-to-ceiling height measured at several points rather than one, skirting and cornice details, the position of switches and air-conditioning outlets, door swing clearance, and whether the wall is truly plumb. Note the room's other finishes as well — flooring tone, wall colour, handle hardware — because a smoked, grey-brown veneer reads differently against pale oak boards than against dark stone.

Then record what is still open. A brief that says "dark timber wardrobes, full height" leaves the door type, internal fit-out and veneer species undecided. Marking those gaps explicitly prevents them from being resolved by whoever happens to be reading the drawing at the factory.

Translate the look into a specification

"Smoked" describes a tone, not a build. To turn it into something manufacturable, separate four decisions:

  • Carcass and door construction — which substrate, which edge treatment, and how the doors meet. Hinged fronts need swing clearance; sliding fronts need a track zone but free up the space in front. Our Wooden Sliding Door Wardrobes show how that layout works when a bedroom is too tight for a door swing.
  • Veneer species and cut — grain figure and cutting method control how the surface reads across a wide door, so state whether a book-matched or slip-matched sequence is required.
  • Finish sheen — the same smoked tone behaves very differently at high gloss and at matte. Reflection, fingerprint visibility and how the grain sits in low bedroom light all change. If you are weighing those two looks, our Matte Finish Veneer Wardrobes and High Gloss Veneer Wardrobes pages show the alternatives in the same collection.
  • Internal layout — hanging heights, drawer banks, shelf spacing and any lighting or mirror element. This is where daily usability is decided.

If veneer also appears elsewhere in the property — a media wall, a pantry run or bedroom doors — group those items in one enquiry so grain and sheen are produced together. Our Wood Veneer Panels and Wood Veneer Hinged Doors are built to the same project-specific approach, which keeps tones consistent from room to room.

Send the drawings that make pricing meaningful

An enquiry becomes quotable when it carries numbers a factory can check. Attach what you have, and say plainly what is missing:

Document or detailWhy the quotation depends on it
Room elevations with overall widths and heightsSets door count, panel spans and whether a structural joint is needed mid-run.
Cross-sections at ceiling and skirtingShows scribes, cornice returns and how the carcass meets an uneven soffit.
Plan showing door swing or sliding track zoneDetermines whether hinged, sliding or open fronts are workable in that room.
Internal fit-out schedule per bayDrives drawer and shelf quantities, hanging rails and any lighting provision.
Finish reference — sample code, board or photographed panelRemoves guesswork on tone; a colour name alone is not a specification.
Hardware preference and who supplies itHinges, runners and handles affect door thickness and cut-outs.
Delivery address, access route and storeyAffects packaging, maximum panel sizes and on-site handling.
Programme dates — site ready and required on siteProduction and shipping sequencing is planned from these dates, not assumed.

Where a detail genuinely does not exist yet, say so. Our interior design services cover space planning, furniture layouts and 3D renderings, so an incomplete drawing set is a normal starting point rather than a blocker.

Expect samples and a written specification before production

For veneer this step is not optional. A tone photographed on a screen shifts under bedroom lighting, and grain spread across a wide door cannot be judged from a thumbnail. Ask for a physical finish board and check it in the actual room at both day and night before signing off.

Then have the confirmed specification sent back to you in writing: dimensions as they will be built, the selected veneer and sheen, the internal layout per bay, hardware responsibility, packaging method and delivery terms. Where your drawings conflict with that confirmation, settle it on paper before anything is cut. That one exchange is what stops a finish decision made in week one from becoming a replacement order in month six.

What to check when the quotation comes back

  • Does every line item name the finish and construction, or does it simply repeat the product title?
  • Are dimensions stated as finished sizes with tolerances, not rounded room measurements?
  • Is the internal fit-out priced bay by bay, so substitutions are visible rather than buried in a lump sum?
  • Which items are excluded — hardware, lighting, on-site installation, packaging for long panels?
  • Do the delivery terms and shipping method match your programme and access constraints? Our logistics and door-to-door delivery service covers freight by sea, air and rail with the associated paperwork, but the applicable terms for your address should be stated in writing against your order.
  • If the unit is being built to your own detail, is that treated as custom and OEM work, with prototyping and finish approval written into the schedule?

A short checklist before you press send

  • Elevations, sections and plan attached, with units of measurement stated.
  • Veneer species, cut pattern and sheen named; finish reference supplied.
  • Door type chosen against the clearance the room actually gives you.
  • Internal layout listed bay by bay, including lighting and mirror decisions.
  • Hardware split defined: who supplies it, who fits it.
  • Delivery address, access notes and required dates included.
  • Open questions listed explicitly, so nothing gets resolved silently at the factory.

Send that package together with a request for a physical finish sample, and the first reply you receive will be a comparable quotation rather than an estimate built on assumptions. That is the point of turning a design brief into an enquiry: it moves every decision onto paper while changes are still cheap.

SANTERSON is a China-based manufacturer and one-stop supplier of furniture and building materials, operating since 2008, serving villa, hospitality and office projects. Wardrobe enquiries are handled through our contact page.