A wall system that slides, folds or hides a doorway looks identical in two quotations and behaves very differently on site. If you are specifying Santerson Textured Sliding Panels for a villa, apartment or hospitality fit-out, the sample panel and the written proposal carry far more information than the product photograph. The steps below show what to request, what to write down, and how to place two or three offers side by side before you commit.

Start from the job, not the finish

Textured sliding panels are made-to-measure. Panel size, layout and finish are set per project, so a comparison is only meaningful once each supplier has been given the same brief. Before you ask for anything, record four things:

  • The opening or wall run to be covered — width, height, floor-to-ceiling condition, and whether skirting, architrave or cornice stays in place.
  • How the panels must move: stacked to one side, bi-fold, or sliding on a track with a defined parking position.
  • What sits behind the panels — storage, a doorway, a service zone — and how often the system will be opened.
  • The finish decision you are weighing: surface texture, sheen level and colour against adjacent joinery, doors and wall finishes.

Send that same brief to every bidder. Quotations in this category often differ by scope rather than by panel cost, so a like-for-like comparison starts with identical inputs.

What to ask for in the sample

Ask for a physical sample of the exact texture and colour you are considering, not a generic catalogue card. A sample lets you judge three things a specification sheet cannot settle:

  • Texture under your lighting. A textured surface reads differently under warm downlights than in daylight, and sheen level changes how much of the relief you actually see. Check the sample against both, at the time of day the room is used.
  • Edge and face consistency. Look at how the texture wraps the edge and whether the colour holds at a grazing angle. Sliding panels are seen close up as they move, so the edge treatment is part of the finish.
  • Coordination with the rest of the joinery. Hold the sample against your wardrobe fronts, concealed doors and panelling schedule. Where one wall carries several systems — Santerson Closet Sliding Panels beside fixed panelling, for instance — a difference in sheen shows up sooner than a difference in colour.

Keep the sample, write its reference on the back, and attach that reference to your quotation sheet. Once two or three offers arrive, samples become evidence rather than decoration.

Reading the proposal line by line

Configurable wall systems are quoted as assemblies. The items below are where two proposals that look similar turn out to be different products.

Line to checkWhy it changes the price and the result
Made-to-measure dimensionsConfirm each panel width, overall run and whether out-of-level walls or floors are allowed for. A quotation built on nominal sizes shifts cost to site variation later.
Panel substrate and finish build-upThe same texture can be produced over different cores and surface layers. Ask what the sample actually shows, so you compare constructions rather than adjectives.
Track, runners and hardwareSliding systems live or fail on hardware. Check what is included: track type, hangers, guides, stops, and whether floor or ceiling fixing is assumed.
Opening geometryStacking depth, return panels and corner details are frequently quoted at different levels of completeness. Compare the drawings, not just the totals.
Scope boundaryState plainly who supplies setting-out, making good, cornice or skirting reinstatement, and final cleaning. Silence here is where change orders appear.
Packaging and deliveryFor panels travelling internationally, packaging specification, container loading plan and delivery address matter as much as unit price. Damage in transit delays the programme.
Installation and handoverCheck whether installation, inspection and snag rectification are included, and what is handed over at completion.

Where a proposal is silent on any row above, treat it as excluded until confirmed in writing. That single habit removes most of the false economy in low bids.

Scoring the offers

Build one comparison sheet with a row per proposal and a column for each item in the table above, plus columns for unit price, delivery term and the lead time as quoted. Then read the sheet down the columns rather than across the rows.

  • A cheaper total that omits hardware or installation is not cheaper; add those costs to the row and re-compare.
  • An offer whose quoted construction matches a physical sample carrying your reference carries less risk than one quoting from a generic image.
  • An offer backed by drawings showing panel layout, stacking direction and section detail shows a supplier who read your brief; one that arrives as a price list does not.

If you are weighing related systems in the same wall build — acoustic separation, a glazed screen, or a media wall that conceals a display — request those quotations on the same basis. Santerson Acoustic Sliding Panels and Santerson Partition Sliding Systems are configured the same way, so one brief and one comparison sheet covers all of them.

Working with a single supplier across the wall build

Wall systems rarely sit alone. In a villa or hotel room they meet cabinetry, doors, flooring and lighting, and each junction is a coordination risk. Where one supplier handles several of those elements, texture and level tolerances get resolved in the factory rather than on site.

SANTERSON is a one-stop furniture and building materials supplier, with custom furniture design and prototyping covering bespoke finishes, textures and material selection. Project work runs through interior space planning and layout design, material and product specification, manufacturing and quality control, project management and site coordination, then installation and after-sales support, with furniture logistics and door-to-door delivery arranged by sea, air or rail including customs documentation.

For buyers comparing offers, that structure means one point of contact for the sample reference, the shop drawings and the delivery schedule. It does not remove the need for the comparison sheet: ask for the same line items from everyone, and hold each quotation to the sample you approved.

Before you sign

Confirm in writing:

  • Panel-by-panel dimensions as measured on site, with tolerances and who verified them.
  • The approved sample reference, and confirmation that production follows that reference.
  • Hardware schedule: track, hangers, guides, stops, and the fixing method for your floor and ceiling construction.
  • What is excluded — making good, electrical work, cornice or skirting reinstatement.
  • Packaging standard, container loading plan, delivery term and named delivery address.
  • Installation arrangement, inspection list and snag process at handover.

Dimensions, substrate, hardware and finish specification for these configurable listings are set per project, so confirm each one against your own drawings before production starts. Where acoustic performance is part of the brief, ask for the figures that apply to the configuration you have chosen — the sliding panel collection includes an acoustic variant, and its performance depends on the build-up specified. A comparison that checks those six points against a physical sample separates the offers more reliably than price alone.

Send your wall schedule, opening dimensions and finish references to the SANTERSON team, and the quotation will match the construction shown on the sample you approve.