A spa plan is really a coordination plan. It has to settle six things before the unit ships: the exact equipment configuration, the access route, a base that carries the filled weight, a dedicated and protected power supply, a water-system layout with service access, and a commissioning record the owner can actually follow. Miss any one of them and the waterfall, which is the whole point of the feature, becomes the source of the problem — splashing onto an unprotected deck, running on an undersized circuit, or landing in a cabinet that cannot be opened for service.
The Square Luxury Hot Spa, Waterfall Feature & LED Lighting from SANTERSON is built on a #304 stainless steel frame with a sealed base, a moisture-free cabinet and an isolated power layout, and it is listed with a massage pump, a circulation pump and an optional air blower; the exact equipment fitted to your unit should be confirmed on the order. That construction decides most of what belongs in your installation plan, so the plan below follows the same order: siting, base, power, water systems, finishes, then handover.
1. The spa specification itself, agreed before anything else
Half of all site problems start because the equipment list was still open when the unit arrived. Fix it in writing first: which pump set is included, whether the air blower is on this order, which lighting fixtures and controller are supplied, and what spout or weir forms the waterfall. Then record the delivered weight, the external dimensions and the footprint of the cabinet, because those numbers drive the base design and the access route.
SANTERSON's wider swim and hydrotherapy range is configured model by model, so the same discipline applies if you are sizing across options. The Outdoor Swim Spa WS-PC05 is listed at 5000 × 3000 × 1100 mm with a total power figure of 2.25 kW, while the Outdoor Swim Spa WS-S06 is listed at 5820 × 2220 × 1110 mm and 6.35 kW, and the longer Outdoor Swim Spa WS-S10 reaches 10000 × 2200 × 1420 mm. Those catalog figures are what the electrical and structural drawings should be built on, and each one needs confirming against your selected configuration rather than copied from a brochure.
2. Siting and access: the questions a survey has to answer
- Where does the water go? A waterfall feature splashes outside the shell by design. Keep the spa away from doors, windows, timber decking edges and any wall that cannot take spray, and plan a drainage fall away from the building.
- Can the unit get there intact? Measure the gate, side passage, turning radius and final lift path. A one-piece acrylic shell on a steel frame cannot be tilted through a narrow side alley, and crane access over an existing roof is a cost line, not an assumption.
- What sits overhead? LED lighting and waterfall pumps need a service point; pergolas, hardtops and gazebos change both the wiring route and how the light reads at night. If you are pairing the spa with outdoor shade structures, fix their position on the same drawing.
- Who sees it? On a terrace or rooftop, the waterfall becomes an audible feature as well as a visual one. Check sightlines and noise against neighbouring properties before you commit to spout height and pump speed.
3. Base and structural support
Water is the load. A square spa with a footprint in the region of 5000 × 3000 mm holds several cubic metres when filled, so a slab or deck designed for furniture alone will not do. The plan should show a level, compacted base with a continuous bearing surface under the whole cabinet, sized by a structural engineer for the filled weight plus live load, and raised clear of ponding water. Because this model uses a sealed base and a moisture-free cabinet, the base must drain away from the cabinet rather than let it sit in water.
On timber decks, add local reinforcement under the seating and jet zones, since vibration from the massage pump travels through lightweight framing. On balconies and rooftops, get the structural sign-off before ordering, not after.
4. Power layout and lighting circuits
The isolated power layout on this spa keeps the electrical zone separate from the wet cabinet, which is exactly why the plan needs a dedicated supply run rather than a shared outdoor circuit. Decide and document:
- the total connected load for the selected configuration, including pumps, air blower if fitted, lighting and any heat source, with a margin for future additions;
- circuit protection and residual-current devices as required by the local electrical code, installed by a licensed electrician;
- the position of the isolator or control panel — reachable when wet, but out of casual reach of children;
- where the LED fixtures land and how they are fed: main underwater lights plus any accent or small LED runs, each on a circuit that can be isolated separately for servicing;
- how the lighting controller is operated — wall panel, remote or app — and where its receiver sits so it stays dry and serviceable.
Do not let the electrical scope fall between trades. The spa supplier, the electrician and the site contractor should all sign the same single-line diagram.
5. Water systems: pumps, jets, waterfall and filtration
The waterfall feature is a pump duty, not a decorative fitting. The plan needs to state which pump feeds the spout or weir, what flow it delivers, and where the water lands, so splash-out and noise are designed in rather than discovered. Alongside it, list:
- massage pump and circulation pump duties, with jet positions marked on the shell drawing against seating positions;
- the air blower if specified, including its air line route and anti-siphon protection;
- filtration: filter pump, filter vessel location, and a clear access door or removable panel for element changes;
- sanitisation choice — ozone, UV or dosing — with its feed point and the power it needs;
- heating source (heat pump, if selected) plus its noise position and clearance requirements;
- fill and drain points, with a drain route that does not cross the terrace surface.
If the project also calls for a longer swim channel or a dedicated relaxation zone, look at it in the same plan rather than as a second purchase. The Luxury Outdoor Swim Spa with Massage Jets, LED & Water Features combines swimming space with hydrotherapy jets and water features, and the Long Outdoor Swim Spa with Hydrotherapy & Relaxation Pool pairs a long swimming channel with a separate relaxation area on a terrace or deck.
6. Surrounds, finishes and integration with the rest of the build
A square spa reads as architecture, so the coping, decking edge and any adjacent cladding need to be resolved on paper before installation. Specify the coping material and fall, the step or entry arrangement, and how cabinet finishes meet the deck line. Where the spa sits against a wall, that wall usually becomes a feature surface, and SANTERSON's wall range can be coordinated in the same order: Luxury Decorative 3D Wall Panel for a textured backdrop, or Aluminum Honeycomb Panel for Building Exterior & Interior Wall Cladding where the surface is exposed to weather. For garden and terrace projects that need curved spa shapes as well, the Customizable Shape Outdoor Spa covers square, round, oval and curved formats.
7. Delivery, logistics and site sequencing
Order the spa against the programme, not the other way around. The plan should name the delivery window, the vehicle size that can reach the site, the lifting method, and the storage position if the base is not ready. SANTERSON's logistics and door-to-door delivery service covers freight forwarding by sea, air and rail, packaging and container loading, customs paperwork and shipment tracking; the import terms, duties and delivery scope for a specific address should still be confirmed case by case in your quotation.
Sequence the trades so that nothing waits: base and drainage first, then electrical containment and the control position, then the spa set, then surrounds and coping, then commissioning. A single coordination drawing with all three scopes on it prevents the usual argument about who owns the gap between the cabinet and the deck.
8. Commissioning, handover and maintenance access
Close out the plan with a written commissioning record: fill and level check, each pump run individually, jet and waterfall flow observed at the seating positions, air blower function, LED fixtures and controller tested through every mode and colour, protection devices tripped and reset, and any insulation or cover verified. Then hand over a simple pack for the owner:
- as-built equipment list with model numbers and serials;
- wiring route and control-panel location;
- water chemistry targets and a routine dosing schedule;
- filter cleaning intervals, with the access panel marked on a plan;
- winterisation or cold-period procedure if the site sees frost;
- spare-parts contacts and what to report if a jet, light or pump underperforms.
SANTERSON lists on-site installation, inspection and snag resolution, warranty coverage, spare parts and ongoing maintenance under its installation and after-sales support. The actual scope, response times and exclusions for your project should be written into the contract before installation begins.
A short checklist to carry into the design meeting
- Confirmed equipment list: pumps, blower, jets, waterfall spout, LED fixtures, controller, filtration, sanitisation, heating.
- Delivered weight, dimensions and access route measured on site, not assumed.
- Engineered level base with full bearing and positive drainage away from the cabinet.
- Single-line electrical diagram: dedicated supply, protection devices, isolator position, separate LED circuits.
- Waterfall landing zone, splash allowance and noise position agreed with the client.
- Service access to filter, pumps and controller without lifting the spa.
- Delivery window, lifting method and trade sequence fixed in the programme.
- Commissioning tests and owner handover pack defined before the order is placed.