Wood veneer panels look simple on a finish schedule: one line, one sample, one approval. They are one of the easiest items for a project to disagree about later, because the visible surface is thin, the substrate behind it is not specified by the same drawing, and every panel in the set is cut to order. When a wall arrives on site with panels that do not match each other or do not fit the setting-out, the question is rarely "who made a mistake" — it is "what was written down".

The documentation below is what we ask for before a wood veneer panel order enters production, and it is the same list our own workshop works from. Procurement teams who capture these items in one place usually find that veneer becomes an ordinary, low-drama package rather than a special case.

Start with the surface, not the product name

A single phrase such as "oak veneer wall panels" can cover several different products. Before anything else, record what is actually being bought, because that determines who supplies it, how it is fixed, and what has to be approved.

  • Wall panel systems — cladding applied to a wall face, as in our wall panel systems range.
  • Built-in joinery panels — veneered fronts and sides that form part of cabinetry, media walls or wardrobe carcasses ordered from the same batch.
  • Panels combined with doors — veneer on the wall plus wood veneer pocket doors or wood veneer hinged doors in the same grain and finish, so the door disappears into the wall.
  • Integrated paneling and concealed doors — where the integrated door and paneling detail is the design intent, and the gap line matters more than the timber.

Note which of these each zone falls under on the drawing. A hotel guest room wall that reads as "panel + concealed door" in one section and "joinery unit" in another is a common source of duplicated or missing scope.

The eleven fields worth filling in for every veneer line item

FieldWhat to recordWhy it causes problems if left blank
Species and cutSpecies, cut method (plain-sawn, quarter-sawn, rift), and whether the figure is part of the design intent.Two panels of the same species can look completely different side by side.
Veneer typeNatural wood veneer, reconstituted or engineered veneer, or a wood-effect laminate standing in for veneer.Colour consistency and grain repeat behave differently; substitutions change the specification.
Grain matching and sequenceBook-match, slip-match or random-match; whether panels across one wall are from a numbered set.Unsequenced panels cannot be re-installed in the intended order after packing.
Colour and sheenStain or lacquer system, sheen level, and a signed physical sample reference with date.Named shades vary between batches; an undated photo is not evidence.
SubstrateCore board type and thickness, and moisture or fire-rated requirements where the project calls for them.The visible finish says nothing about what is behind it; weight and fixings depend on it.
Panel dimensions and setting-outWidth, height, thickness, joint detail, and the approved setting-out drawing per wall or room.Made-to-measure panels are cut from one dimension set; two versions of a drawing produce two walls.
Edge and trim conditionSquare edge, shadow gap, bolection, metal trim, or mitred external corner.Detail is decided on site if not drawn, usually against the wrong sample.
Interface itemsSkirting, reveal at ceiling, architrave or no architrave, and how the panel meets stone, glass or plaster.Trade boundaries shift and the trim gets ordered twice or not at all.
Fixing method and substrate preparationBattening or framing layout, adhesive or mechanical fixings, and who prepares the wall behind.Panels arrive for a wall that is not flat, level or set out to the drawing.
Cut-outs and servicesSwitches, sockets, TVs, integrated lighting, speakers, sprinkler heads — with coordinates on the setting-out drawing.Panels cut in the wrong place are scrap; a site-cut repair is visible.
Room-by-room quantities and pack numbersPanel count per room or wall, plus spares held locally for future maintenance.A batch re-ordered months later rarely matches the original grain and colour.

For each line item, keep one identifier that everyone uses — drawing number, room code and panel code together. When a query comes back from the factory referencing that code, the answer is already in the schedule.

Samples: get the right one, keep it, and date it

A veneer sample answers three questions, and a single small offcut answers none of them. Ask for a panel-sized sample that shows the grain sequence, then approve against it in the actual room lighting at the time of day the space is used.

  • Request a sample in the same finish system and on the same substrate as production, not a loose veneer swatch.
  • Have the approving party sign and date it, photograph the signed label, and store the physical sample — it is the reference for every later query and any future replacement order.
  • Where a project mixes finishes, approve the veneer next to the adjacent stone, metal and fabric samples rather than in isolation. Our stone and marble panels, textured panels and glass and glossy panels are frequently specified alongside veneer, and the contrast between them is what the room actually reads.
  • Record the sample reference on the purchase order itself, not only in the correspondence.

Coordinate veneer with the joinery it sits beside

Veneer panels rarely stand alone. In villas and hospitality rooms they continue into cabinetry, media units and wardrobes, and a mismatch between the wall and the unit next to it is immediately obvious.

  • Order matching veneer items from one supplier and one batch wherever the surfaces sit in the same sightline — for example wood veneer European cabinets, natural wood veneer cabinets and the wall panels that wrap around them.
  • Where lighting is built into the panelling, confirm the electrical detail — driver location, access, cable route and heat — before the panel size is fixed. See integrated LED media units for how lighting and joinery are specified together.
  • Decide the sequence of installation between panels, doors, flooring and ceiling, and write it into the programme. Panels installed before the wet trades finish get damaged; installed after the services get cut on site.

What to confirm before the order is released

  • The setting-out drawing for each wall or room is the approved version, with revision number and date recorded on the purchase order.
  • Site-verified dimensions are used, not design-stage dimensions — including floor-to-floor heights, out-of-plumb walls and door openings.
  • Panel numbering matches the drawing so the packing list can be checked against it room by room.
  • The signed sample reference is quoted on the order and repeated on the packing list.
  • Fixing method, trim details and cut-out coordinates are attached to the order rather than promised in email.
  • Delivery location, packaging specification and container loading plan are agreed for logistics and door-to-door delivery, along with who inspects panels on arrival and how damage is recorded.
  • Spares quantity is decided now, while the batch still exists, and stored on site rather than in the factory.
  • The installation scope is clear: installation and after-sales support can cover fixing and snag inspection, but confirm what applies to your project before the programme is set.
One habit that saves the most time: keep every veneer decision in a single schedule with revision control — species, cut, match rule, finish reference, substrate, dimensions, panel codes, sample date and spares. When a query arrives, you answer it from the schedule instead of searching email for what was agreed.

Where this fits in a one-stop procurement

We manufacture and supply furniture and building materials for villa, hospitality and office projects, with custom and OEM service covering made-to-measure sizing, material and finish selection, and layout tailored to the project. For furniture sourcing for Australian projects, panel schedules like this are reviewed with drawings before quotation, so the specification is settled before production starts rather than during it.

If you send a schedule in this format — room code, wall reference, finish sample, dimensions and quantities — we can quote against it directly and flag anything missing before the order is released.

Send your panel schedule, drawings and finish references to SANTERSON for a specification review before production. Phone / WhatsApp +86-13928214007 (PHILLIP), email santerson@qq.com.