A wardrobe order rarely goes wrong at the drawing board. It goes wrong in the gap between what the drawing says and what the factory was asked to build. For Smoked Glass Aluminum Frame Wardrobes, that gap is unusually easy to fall into: tinted glass reads differently under site lighting than on a sample board, an aluminium frame profile changes the clear opening without changing the external size, and made-to-measure casings turn a single mis-read dimension into a re-order. A product submittal is how you close that gap before purchase orders are cut. Below is what to ask for, in the order most project teams review it.
What a submittal actually has to do
A submittal is not a brochure. A brochure tells a buyer that a product exists; a submittal lets a consultant, a builder and a factory quote the same object from the same paper. For custom joinery supplied from a furniture and building materials manufacturer, the submittal also has to carry everything that standard catalogue specification does not: room-by-room dimensions, the finish selected from a range, and the interface with floors, ceilings and adjacent cabinetry.
Judge any submittal you receive by one test. If a site supervisor could install the wardrobe without phoning the supplier for clarification, it is complete. If they cannot, find the missing line item and request it in writing before you commit.
1. The exact product reference, not the collection name
Glass-fronted aluminium wardrobes are sold as collections with several variants under one family name. A submittal that says only "glass and aluminium frame wardrobe" is not verifiable. It should name the specific product page or SKU, and state which collection it sits in, so that when you compare two quotations you know you are comparing like with like.
This matters more than it sounds on glass products. The same frame profile can carry smoked glass, bronze glass, clear glass or frosted glass, and each variant is a separate product line with its own reference. A submittal that names the collection but leaves the variant to be "confirmed later" has not specified the wardrobe at all.
2. Dimensioned elevations for each room
Made-to-measure sizing means every set is cut to a specific opening, so dimensioned elevations are the core of the document rather than an appendix. Ask for:
- an elevation per wardrobe, marked with overall width, height and depth;
- the internal bay split — hanging sections, shelving, drawers — with each module dimensioned;
- setting-out dimensions from fixed site references (room datum line, finished floor level, door reveal);
- clearances for skirting, cornice, built-in lighting and any adjacent tall cabinetry.
Then check the drawings against your own architectural set. Where they disagree, get the discrepancy resolved on paper before production starts, not at the site handover meeting.
3. Frame profile and glass construction stated separately
Two things are often blurred into one line: "aluminium frame with smoked glass". A workable submittal separates them, because each carries its own tolerances and its own risk.
| Item | What the submittal should state | Why it matters on site |
|---|---|---|
| Frame profile | Section shape and face width of the aluminium stile and rail; corner joint method | Face width sets how much glass is visible; the joint method determines whether whether a damaged stile has to return to the factory |
| Frame finish | Named colour or treatment, plus the sample reference it was approved against | "Black" from two suppliers is not one colour; a sample reference ends the argument |
| Glass type and tint | Smoked glass as selected from the supplier's own range, with its product reference | Tint depth varies across batches and between suppliers; matching to an approved reference is what protects the look |
| Glass thickness and edge treatment | Thickness, edge polish, and whether the panel is framed or bonded | Drives hinge and runner loading, and whether a replacement panel can be glazed on site |
| Door type | Hinged, sliding or open configuration per unit, with track or hardware reference | Sliding doors need pocket and track depth that hinged doors do not; this is the most common late clash with flooring |
Where a supplier's own product page lists a specification area, cross-check it against the submittal. If the two disagree on a name or a number, do not pick one and move on — ask which governs, and record the answer.
4. Interior layout and hardware schedule
Glass doors hide everything that determines whether a wardrobe works. Ask for a hardware and interior schedule listing, per unit: hanging rail positions and heights; shelf spans and adjustable pitch; drawer units and their run type; integrated lighting if specified; and any accessories such as pull-out hampers or display niches. Each line should reference the item by name so that substitutions have to be declared rather than discovered.
Where the submittal offers a choice — soft-close runners versus standard, for example — get the selected option written down. "As per supplier standard" is not an approval; it is a deferral, and deferrals surface as variation claims.
5. Material and finish approvals, with physical samples
Smoked glass cannot be approved from a photograph. Request a physical sample of the tinted glass and of the frame finish, both mounted and labelled, and hold them against your interior palette under the actual room lighting before you sign anything off. Then require the submittal to carry the same sample references.
This is also where bespoke finishes are handled. Suppliers offering custom furniture design and prototyping, bespoke material finishes and textures, and OEM production will normally quote these as options rather than defaults — see their custom and OEM service. If your project needs a non-standard tint, frame colour or branded detailing, the submittal is where it should appear, described in words that survive translation.
6. Interfaces: what the wardrobe touches
Most site defects on built-in wardrobes are interface defects, and they are cheap to resolve on paper and expensive to resolve in timber and glass. The submittal should show how the unit meets:
- the finished floor level, including any underlay or threshold build-up;
- the ceiling, where a full-height or floor-to-ceiling configuration is specified;
- adjacent wall panelling, concealed doors and kitchen cabinetry where the same finish family continues;
- electrical points for integrated lighting, including who supplies the drive and the wiring.
Ask explicitly which trades prepare each interface and by what date. A submittal that documents the wardrobe but not its boundaries has told you half the story.
7. Packaging, sequence and delivery plan
Glass-fronted units in aluminium frames are fragile and easy to mix on site once crates open. The submittal or its attached delivery schedule should state packing method and protection for glazed panels, the crate marking convention, and — for multi-bedroom projects — which units are released in which batch. Where freight is arranged door to door by sea, air or rail, with customs documentation handled by the supplier, confirm that the packing list matches the submittal unit numbering exactly.
Numbering discipline pays for itself twice: it prevents wrong-room installation, and it lets a missing part be identified from the drawing rather than from a photograph of a crate.
8. Installation method and after-sales scope
Ask how the units are fixed, levelled and glazed on site, who performs the installation, and what happens when a panel is damaged after handover. A complete submittal names the fixing system, the tolerance allowance out of plumb, the snag inspection step, and the warranty and spare-parts position in writing. Response-time promises found on marketing pages should be confirmed for your specific project before they are relied on in a programme.
Where installation and after-sales support form part of the supply scope, request that detail as part of the same document set rather than negotiating it separately after delivery.
A short checklist for procurement teams
- Does the document name the exact product variant, not just the collection?
- Are elevations dimensioned per room and tied to site datums?
- Are frame profile, frame finish, glass tint and glass thickness each stated separately?
- Is every hardware option selected rather than deferred?
- Do sample references in the submittal match samples you physically hold?
- Are floor, ceiling, panelling and electrical interfaces drawn and assigned?
- Does crate marking follow submittal unit numbering?
- Is installation responsibility and after-sales scope written into the pack?
If you can answer yes to all eight, the submittal is doing its job. If any answer is no, send it back with that single item named — suppliers respond far faster to one specific request than to a general query.
Related products worth reviewing in the same package
Wardrobe submittals go smoother when the whole glass-and-metal family is specified together, because the frame profile and finish decision then gets made once. Alongside smoked glass aluminium frame wardrobes, compare Bronze Glass Aluminum Frame Wardrobes and Frosted Glass Aluminum Frame Wardrobes for rooms where full transparency is unwanted, and Smoked Glass Wardrobes where a glass-door construction rather than a framed one suits the detail. For walk-in rooms, Glass Walk in Wardrobes keeps the same tint language across a larger footprint.
Where wardrobes sit in the same sightline as Smoked Glass Aluminum Cabinets, specify both together and ask for one matching finish reference to cover them. Coordinating built-in joinery, wall panelling and one-stop supply of furniture and building materials through a single supplier is what keeps a tint consistent from the bedroom to the kitchen.
Frequently asked questions
Should the submittal include prices? No. A submittal is a technical document; keep commercials in the quotation so that technical revisions do not reopen pricing every time.
Who prepares it — the designer or the supplier? The supplier issues it, and your design team marks it. Ask for it in the same format you use for other joinery packages so it can be reviewed against the same checklist.
Is one submittal enough for a whole apartment? One document, but with separate elevations and unit numbers per room. A single generic detail drawing across several rooms is where made-to-measure supply quietly becomes off-size supply.
What if the tint looks different after installation? That is why physical samples with matching references belong in the approved pack. Keep the signed samples through handover; they are the only practical evidence of what was agreed.
If you are specifying glass-fronted wardrobes for a villa, hotel or multi-unit project and want a submittal pack that already answers these questions, send your room set and finish intent to SANTERSON — China, +86-13928214007, santerson@qq.com.