Niche shelving is one of the smallest items on a bathroom schedule and one of the most frequently changed later. It sits in a wet zone, it has to line up with tiles and other joinery, and it carries the things people reach for every day. Before we manufacture a run of niche shelving for a project, we ask the client for the following details, because each one changes the drawing, the material choice and how the unit is installed.
1. The wall build-up and the finished line
Send us the wall section, not just a nominal depth. A niche framed into studwork behaves differently from one formed in masonry, and different again inside a shower enclosure where waterproofing has to lap into the recess. We need the finished face of the tile or panel, the thickness of the adhesive bed, and whether the back of the recess is open or needs a closed backing panel.
Tell us which wall you want the shelving on. A run that starts at a corner has to be drawn as corner open shelving, with the return dimension settled before production, otherwise the shelf ends meet the tile line awkwardly and the difference shows once the grout is in.
2. What will actually be stored there
Storage habits set the shelf depth and spacing far more reliably than a standard catalogue dimension. Guest toiletries need a shallow shelf; tall bottles, towels folded three deep, or a hair appliance need a deeper recess and a taller clear opening between shelves.
We build to your list rather than to a fixed module: made-to-measure sizing, layout tailored to the room. Where a household needs more than a recess can hold, we move part of the load into floating vanities and tall cabinets, and keep the niche for daily items only.
3. Fixing method and load
The fixing detail depends on the substrate behind the finish. A shelf fixed into timber framing carries a very different load from one hung on masonry or on a cavity wall with boarding, so we confirm the substrate before we decide between concealed brackets and a fixed shelf carrier. Glass shelves, metal frames and solid timber shelves also have different bearing requirements.
If the niche is above a basin, the tap spout and the mirror both sit in the same zone, so we check projection heights against the shelf underside to avoid splashing and head contact.
4. Finish, lighting and how it meets the tiles
The finish has to match something already specified: the cabinet door, the wall panel, the tapware. Send us the finish reference or a sample, and we match the shelf boards, edges and any frame to it.
If you want lighting inside the recess, decide before manufacture. A lit niche needs a cable route, a driver location and a switch point; drilled and wired later means visible trunking. The same applies where the niche is part of a larger wall: an open display niche set into a storage wall is drawn together with the surrounding panels, so the reveal and shadow gap stay consistent across the whole elevation.
5. Room type and how much use it will see
A family bathroom, a shower room that gets steam every day and a guest cloakroom put different demands on the board and edge treatment. We select materials accordingly, and we say so on the shop drawing rather than assuming one specification covers all rooms in the same building.
The same logic applies to custom niche paneling, where the recess is formed within panelling instead of a masonry pocket. There, the panel thickness and the trim detail set the look of the opening.
6. Quantities, site access and installation sequence
Send us the room-by-room schedule with the dimensions, so we can produce matching units in one batch instead of re-cutting on site. For apartments, tell us about lift sizes, stair widths and floor protection requirements; a shelf that cannot reach the bathroom intact is a delivery problem, not a manufacturing one.
We work to the trade sequence: the niche goes in after waterproofing and setting-out are confirmed, and before the final decoration. Our team covers design consultation and space planning, material selection and product specification, manufacturing and quality control, project management and site coordination, then installation and handover.
What the buyer sends, what we ask back
A clear enquiry usually contains the room elevation with the niche position marked, the wall build-up (substrate, waterproofing, tile or panel thickness), the intended shelf depth and clear height between shelves, and the quantity per room. We come back with a shop drawing showing the opening size, shelf positions, fixing method and finish reference, for your sign-off before production.
- Shelf depth, clear height between shelves, and what will be stored on each shelf
- Finish reference to match, plus any lighting requirement and switch location
- Quantity per room and the site access constraints
SANTERSON is a China-based furniture and building materials manufacturer working on villa, hospitality and office projects, with custom and OEM production, door-to-door delivery and installation support. Send us your drawings and finish references and we will return shop drawings for your approval before anything is cut.
Email santerson@qq.com or contact PHILLIP on +86-13928214007 to discuss your bathroom joinery schedule.