A wall mounted shower set looks simple on a rendering: a square head overhead, a hand spray on a bar, a mixer body on the tile. On site it is a different matter. The water supply has to be opened at the right height, the concealed or exposed piping has to match the outlet spacing, the tile has to be cut around the escutcheon, and the digital unit needs a body that can actually be reached and serviced. When any of that is decided after the tiles are laid, the bathroom ends up with extension pieces, silicone build-up and a shower head that sits off-centre.
The Gun Grey Digital Display Rain Shower System is a wall mounted bathroom shower set with a large square overhead rain head, a multi-function handheld sprayer and a real-time temperature display, supplied for residential villas, apartments and hotel bathrooms. Below is the checklist we ask project buyers, contractors and designers to settle before the order is placed, so that the same drawing works in the factory, on the pallet and on the wall.
1. The product scope written out line by line
The first page of the plan is a bill of materials, not a photograph. For this set the components to list are:
- Mixer body with digital screen — matte gun grey finish, shows water temperature while the shower runs.
- Square overhead rain shower arm and head — the fixed rainfall outlet.
- Handheld sprayer with multiple spray modes — used for rinsing, bathing children or washing down the shower enclosure.
- Slide bar — height adjustment for users of different heights.
- Hose and diverter — moves the flow between the overhead head and the handheld.
- Installation accessories — fixings, escutcheons and connection parts are included with the set, which is what makes it a set rather than five separate purchases.
Write each line into the purchase order with its quantity and its position on the wall. Two bathrooms sharing one drawing but mirrored left to right should be marked as such, otherwise the slide bars end up on the wrong side of the enclosure.
2. Water supply: outlets, height, spacing
This is where most shower-set plans fail, and it is decided before a single tile is ordered. Confirm and record:
- Hot and cold outlet centres, and whether the plumbing is exposed on the finished wall or set into a chase behind it.
- The height of the outlets relative to the finished floor level, stated as FFL, not to the structural slab.
- The distance from the outlet to the shower tray or drain line, so the overhead arm clears the glass and the bather.
- Static water pressure and flow available at that floor. A wide rainfall head behaves very differently on a low-pressure header tank than on a mains-fed line, and the difference is felt by the guest, not argued about on paper.
- Whether the riser for the overhead arm passes through a beam, a stud wall or a waterproofed wet zone, and who owns that cutting work.
If the wall is masonry, note the fixing method in the plan as well. Solid-wall fixings and stud fixings are different details, and the difference shows up on site as a loose body two months after handover.
3. Where the digital display earns its place
The built-in screen shows real-time water temperature, which matters most where the people using the shower cannot judge heat reliably on their own: villas rented to families, serviced apartments, and hotel rooms turned over by staff who never see the bathroom after the guest leaves. It gives housekeeping a quick way to confirm the control is holding, and it reduces the first-day complaint about water that swings hot and cold.
Decide in the plan where the body sits so the screen is legible from inside the enclosure without the bather turning around, and where a hand can reach the control while wet. A body placed behind the spray pattern of its own overhead head is uncomfortable to operate. Keep the display clear of the direct water jet and of the glass panel's splash line.
4. Handheld sprayer position and slide bar travel
The handheld is not a spare part; it is the function that gets used daily. Plan its bracket height for the tallest regular user, then check the hose route so the sprayer slides without dragging across the tile or catching on the glass. Where a shower enclosure has a niche, confirm the slide bar does not collide with the niche edge at the top of its travel.
For accessible or elderly-occupied bathrooms, record the required reach range in the drawing and check it against the slide bar's actual adjustment limits before ordering. This is also the point where a project should look at the rest of the bathroom sanitary fixtures together, because the shower outlet, the basin tap and the WC pan all compete for the same piped zone.
5. Finish, substrate and long-term upkeep
The matte gun grey surface resists water stains and fingerprints, which is why it holds its look in a shared bathroom. Two practical notes for the plan:
- Match the finish across everything visible in one room. A shower set specified against interior fixtures chosen separately — basin, towel rail, lighting — will read as an accident if the metals drift.
- State the cleaning regime in the handover file. Abrasive pads and strong acidic descalers damage a matte coating; hard-water regions need a mild routine instead. Housekeeping manuals written without that line are how a two-year-old shower starts looking five years old.
6. Coordination with the other wet-room trades
A shower set crosses four work packages: plumbing, waterproofing, tiling and ceiling or glass. The plan should name the sequence — outlets set and pressure-tested, waterproof membrane dressed around the penetration, tile set out with the escutcheon landing on a full tile rather than a cut, then the set fitted last.
Where the same project also specifies vanities, basins and WCs from one supplier, grouping those orders avoids two different fixing heights arriving from two different pallets. SANTERSON supplies bathroom ceramics, showers, lighting, cabinetry, wall panels and flooring as one procurement package for villa and hospitality projects, which is what lets a single drawing govern the whole wet zone.
7. Quantities, spares and site storage
- Order against room-by-room schedules, not a floor total. Mirror-image bathrooms count as separate rooms.
- Add a small spare allowance for handheld heads and hoses on hospitality work; these are the parts that wear first and the ones a maintenance team replaces without a shutdown.
- Keep sets in their cartons, upright, in a dry room until the tiling trade has finished. Fitted early, they collect grout haze and scratches.
- Photograph the outlet positions before the wall is closed, and keep that photo with the as-built record. It answers every later question about what is behind the tile.
8. Handover checks worth writing down
Before signing off a bathroom, run through: the diverter switching cleanly between head and handheld with no weep at either outlet; the slide bar holding position under spray pressure; the display reading steadily while water runs; the hose routing freely through its full travel; and the escutcheons sitting flush against tile with a clean silicone line. Record each item on the snag sheet, and hand the cleaning regime over with it.
A wall mounted shower set fails as a project detail far more often than as a product. Settle the outlets, the reach heights, the finish pairing and the sequence of trades on paper first, and the fitting stage becomes the shortest day on the bathroom programme.
For bulk orders, room schedules or a specification review before you place a purchase order for villa, apartment or hotel bathrooms, contact SANTERSON.