A product submittal is the document package a buyer, designer or contractor reviews before they approve cabinetry for manufacture. For open shelving minimalist cabinets, the submittal matters more than it does for a run of closed doors: an open bay shows everything. Shelf spacing, edge detail, fixing method and finish continuity are all visible once installed, so anything left vague in the paperwork becomes a site problem later.

Below is the checklist we work to when we prepare submittals for our minimalist kitchen cabinets collection, including open-shelving units made for residential and hotel projects. Use it as a review sheet whether you are approving one villa kitchen or a whole apartment package.

1. Confirmed dimensions and setting-out drawings

Open shelving is usually made to measure, so the submittal should start with dimensioned drawings rather than a catalogue image. At minimum it should show overall height, width and depth; shelf thickness and clear vertical spacing between shelves; the position of each bay relative to walls, corners and appliances; and how the unit resolves against the ceiling and adjacent closed cabinets.

Check that the drawings are keyed to the same room layout used for the rest of the joinery. A shelf bay drawn from a superseded plan is one of the most common causes of rework, because there is no door front to hide a gap.

2. Material and finish schedule

State the substrate, the surface material and the decorative colour for every component, not just the carcass: shelf panels, side panels, back panels, edge banding or solid edging, and any integrated lighting channel. For minimalist work we typically specify flat panels with concealed handles or touch-to-open hardware on the closed elements, and the open shelves have to match those surfaces exactly where they meet.

Ask for physical samples of the shelf surface and its edge detail together. A shelf face and its front edge are often produced by different processes, and a colour that matches under shop lighting can read differently against a matte door in daylight.

3. Loading and span data for each shelf

Open shelves carry real weight, so the submittal should record the intended use of each bay — glassware, cookware, books, display pieces — and the corresponding span between supports. Where a bay is wide or will hold dense items, ask whether the shelf thickness, material or support spacing has been adjusted for that load rather than kept at the standard detail.

For bathroom and wet-area applications, the same point applies to humidity and to what sits on the shelf. Confirm the board type and edge sealing for damp locations before approval, not after installation.

4. Fixing method and interface with the structure

Because there is no closed carcass to conceal brackets, the fixing detail belongs in the submittal: bracket type and finish, whether shelves are fixed or adjustable, how the unit ties into the wall substrate, and what allowance has been made for services behind the wall. If a shelf crosses a tile line or a change in substrate, that should appear on the drawing.

5. Integrated lighting and electrical coordination

Where open shelving is specified with under-shelf or in-panel lighting, the submittal should include the profile section, the driver location, cable routes, switch or sensor position, and the colour temperature decision. Lighting that is decided after the carcass is built usually means a visible surface trunking.

6. Scope split and interface responsibilities

The submittal should say plainly what is included in the supply and what sits with others on site: who prepares the wall, who supplies stone or engineered-stone shelf tops if used, who makes good around fixings, and which trades complete the final handover. In a one-stop package this line is easy to blur, so write it down for every open unit.

7. Related items in the same approval cycle

Open storage rarely appears alone. If the design also calls for corner open shelving, review it in the same submittal round so the finish, shelf depth and edge profile are approved against one drawing set rather than two.

8. Approval, tolerance and sign-off record

Close the package with a signature block: revision number, date, who reviewed it, what was changed since the previous issue, and the tolerances accepted for on-site adjustment. A submittal without version control is how two different shelf heights end up in one apartment.

A practical test before you approve: read the package from the point of view of the installer who will fix it, and then from the client who will live with it. If either could ask "what happens here?" and find no answer in the drawings, send it back.
Submittal itemAccept when
Dimensioned drawingsEvery bay is dimensioned and keyed to the current room layout
Finish scheduleSubstrate, surface, edge detail and hardware listed per component, with samples signed off
LoadingIntended use stated per bay; span and thickness confirmed for that load
FixingsBracket type, finish, substrate condition and services shown on the drawing
LightingProfile, driver location, cable route and colour temperature specified
Scope splitInclusions and site responsibilities named for each unit
Sign-offRevision number, date, reviewer and accepted tolerances recorded

Figures, materials and hardware options are project-specific. Confirm dimensions, board type, loading and installation requirements for each selected configuration before manufacture.

SANTERSON manufactures minimalist kitchen cabinets and open shelving to project-specific sizes, layouts and finishes, with design coordination, production, door-to-door delivery and installation support under one contract. Send us your drawings and we will return a submittal package built to the checklist above.