A wall-mounted media wall looks simple on a drawing: a panel fixed to the wall, a screen hung in front of it, some shelving around it. In practice it is one of the few pieces of joinery in a villa or apartment that carries electrical services, supports a heavy screen, has to survive an inspection and still reads as a designed feature. That is why our project teams ask buyers for a written installation plan before production starts on Santerson Wall Mounted Media Walls. The units are made to measure, with the finish, layout and dimensions set per project, so everything that has to be true about the wall, the services and the sequence of works needs to be settled while there is still time to change it.
The plan does not have to be long. It has to answer a fixed set of questions, each of which has a cost or programme consequence if left open. Below is the list we work from, with what to record against each item and why it matters for a wall-hung system.
1. The wall itself, verified on site
Nothing in the rest of the plan is reliable until the supporting structure is confirmed. For each media wall elevation, record:
- The actual construction behind the finish — masonry, concrete, stud partition with timber or metal framing, or a framed cavity built as part of the fit-out.
- Finished floor-to-ceiling height and the width of the available run, measured on site rather than taken from a drawing that may not reflect as-built conditions.
- Whether the wall is plumb and square within the tolerance the panel system expects, and who is responsible for bringing it into tolerance.
- Whether the wall can carry the screen plus bracket and panel assembly, or whether a backing frame has to be introduced. A light-gauge stud partition that carries nothing today usually needs noggings or a steel backing designed in from the start.
If a load path cannot be established by inspection or from the structural information available, stop there and have it confirmed. Wall-hung media assemblies are not a place to make assumptions.
2. Screen and equipment specification
The screen drives the fixing detail, so record it before the panel is cut:
- Screen size, weight and VESA pattern, plus the bracket type — fixed, tilt or full-motion arm. A pull-out arm changes both the load and the depth of the recess.
- Whether the screen sits proud on the panel surface or is recessed into it. A recess needs a framed opening with an edge detail, plus clearance behind for the bracket and connector depth.
- The equipment that has to live near the screen: soundbar, set-top boxes, console, router, media player, and whether each item is ventilated or enclosed. Enclosed electronics need a ventilation route decided with the layout, not discovered at handover.
- Remote-control and sensor line of sight. If the design hides equipment behind doors or a sliding panel TV system, confirm how the signal reaches the devices or how they are switched.
Where a screen will be supplied by others, get the manufacturer's fixing sheet into the plan. Where the buyer has not chosen yet, note the maximum size and weight the design is being engineered for, so the panel can be revised rather than rebuilt.
3. Services: power, data, low voltage and lighting
This is where most rework happens, because joinery and services sit with different trades on site. The plan should carry a marked-up elevation showing:
- Every socket position behind and below the screen, with height from finished floor, and enough outlets for screen plus equipment without trailing leads across the face of the unit.
- Low-voltage runs — HDMI, network, speaker cable, IR or control wiring — with routes, terminations and pull-in points so a failed run can be replaced without removing the panel.
- A labelled schedule of what each cable is for. Unlabelled conduits behind a fixed panel become unusable within a year.
- Integrated lighting, if specified. LED media units need the driver location, switching or dimming method, and an accessible route to the driver decided before the carcass is assembled — drivers fail and must be reachable.
Any mains work, and any penetration of a fire-separated wall or floor, should be shown on the plan with the responsible party named. Electrical work in the media wall is not part of the joinery scope unless it has been explicitly agreed as such.
4. Layout, storage and how the wall will be used
Ask what the household or guest actually does in the room, then set the zoning. A media wall that only holds a screen wastes the rest of the elevation; one packed with closed cupboards loses the display value.
- Open shelving for display and frequently used items; closed storage for consoles, games, cables and clutter. Most villas want both, so decide the split per bay.
- Shelf spans and shelf depths sized for what will sit on them — books and stone objects load shelves far more heavily than decorative boxes.
- Door type and swing clearance, including whether adjacent doors or drawer fronts clash when open.
- If the elevation continues into a full-height run, whether to keep the media wall consistent with full height media walls elsewhere in the property so the joinery reads as one system rather than separate purchases.
- Fireplace, artwork or architectural features sharing the same wall, and their clearances from the screen and from any lighting.
5. Materials, finish and specification record
Recorded once and referenced by everyone: substrate and thickness, door and panel material, edge treatment, handle or handleless detail, hinge and runner brand and model where hardware is specified, colour or veneer reference, and the sample approval you are signing off against. Veneer and textured finishes vary between batches, so approve a physical sample and keep it; a colour code on a purchase order is not enough.
Also record what is excluded from your scope. Wall finishes, structural alterations, electrical work and screen supply are the items most often assumed to be included when they are not.
6. Fixing method and access route
- The fixing strategy: concealed French-cleat or rail system, brackets into a backing frame, or through-fixings — with the anchor type matched to the verified wall construction.
- Panel module sizes and total weight per module, checked against the route from the delivery point to the room. Upper-floor villas and apartments routinely defeat long panels at stair turns and lift doors, so measure the access path, not just the opening.
- Splitting strategy for oversized panels, with the joint position shown on the elevation so it lands on a design line rather than mid-field.
- Protection of completed floor and wall finishes, and where the installers can stage material in a live building.
7. Programme and trade sequence
A media wall sits at the end of several dependencies, so put them in order on the plan:
| Stage | Must be complete before joinery is measured or installed |
| First fix | Backing frame, containment and cable pulls tested and labelled; screen bracket position agreed |
| Wet trades and finishes | Plastering, painting and floor finishes complete to the finished level the panels will reference |
| Final measurement | Site re-measure after finishes, against the verified wall and set-out |
| Production | Approved drawings, sample-approved finish, confirmed hardware schedule |
| Installation | Room secure, services live and tested, other trades off the elevation |
For a made-to-measure unit ordered from the factory, production time sits between measurement and installation, so any change after the re-measure carries both a cost and a delay. Freeze the screen choice and the services layout before that point.
8. Inspection, snagging and handover
- A snag list walked through with the client or clerk of works at installation: door alignment, gaps, hardware operation, stability of the panel under hand pressure.
- Photographs of concealed services before the panels close up, saved to the project file. They are worth having the first time a cable has to be traced.
- Screen and equipment commissioning in front of the client, with all sources tested and remote operation confirmed.
- Care and cleaning instructions for the selected finish, plus spare-parts and warranty contact details recorded on one page.
A practical note on scope: our media wall listings are configurable, so dimensions, materials, hardware and electrical options are confirmed per project rather than fixed in a catalogue. The installation plan is the document where those confirmations are recorded, and it is what we quote and build against.
How a single-supplier route simplifies the plan
The hardest part of a media wall is rarely the unit itself; it is that the panel, the storage, the lighting and the adjacent finishes usually come from different suppliers with different drawings and different site programmes. Where the media wall is ordered as part of a wider fit-out, the same drawing set can carry the living-room joinery, integrated LED media units and bedroom storage, with one measurement visit, one finish schedule and one installation team. That is the point of a one-stop furniture and building materials supplier: fewer interfaces to manage, and no argument on site about where one scope ends and another begins.
If you are preparing a media wall package for a villa or apartment project, send the elevation drawings, the verified wall construction and the services layout, and we will return a made-to-measure proposal with the fixing detail and hardware schedule shown. Our installation and after-sales support covers on-site fitting, snagging and follow-up, so the plan and the installation are coordinated by the same team from measurement to handover.