A wall-hung basin looks simple on a villa drawing until the first rough-in drawing lands on site. Then the questions start: which wall can carry the load, where the waste exits, how deep the bowl is under the window sill, and whether every bathroom in the building will still look like one design once the samples are opened. The Wall Hung Ceramic Basin 1004B, Modern Wall Mount Bathroom Sink answers several of those questions at once, which is why it keeps appearing in villa and hospitality schedules. This guide walks through the checks we recommend before you fix that model number into a specification.

Wall Hung Ceramic Basin 1004B, modern wall mount bathroom sink with trapezoid shape and glossy ceramic glaze

Model 1004B wall-hung basin: compact wall-mounted form with a single tap hole for a deck- or wall-mounted faucet.

Why villa projects keep specifying a wall-hung basin

In a villa the same bathroom has to work for daily family use, for guests, and in the photographs that sell the property. A wall-mounted basin helps on all three counts because it releases the floor. The void underneath makes a narrow guest powder room read wider than it is, and it lets floor tiling run through uninterrupted instead of stopping around a vanity carcass.

There is also a practical side that housekeeping teams care about more than designers do. With nothing sitting on the floor, mopping takes seconds rather than minutes, and there is no timber or board substrate sitting in a wet zone to swell over the years. That is why wall-hung ceramics show up so often in the guest bathrooms of villa and bathroom fixtures schedules, rather than only in the main ensuite.

Check 1: what the page actually tells you about the 1004B

The published listing for model 1004B describes a vitreous ceramic basin with a smooth glossy glaze, a trapezoid minimalist outline, and wall fixing through a back panel. Its stated overall size is 510 × 420 × 380 mm, and it comes with a tap hole for single faucet installation.

Read those four details as decision points rather than decoration:

  • 510 mm width is a compact footprint. It suits guest bathrooms, cloakrooms and staff washrooms where a 600–900 mm vanity would crowd the circulation. Measure the clear width between your finished wall finishes, not the structural wall.
  • 420 mm projection sets how far the bowl reaches into the room. Check it against door swings, towel rails and shower screens before the basin position is set out on site.
  • 380 mm height keeps the bowl shallow enough to sit below most window sills and mirror lines, but confirm your finished floor level before fixing the outlet height.
  • Single tap hole means one faucet, so a three-hole basin mixer is not an option here. Decide early between a deck-mounted single mixer and a wall-mounted spout with concealed rough-in, because those two decisions affect the wall build-up.
The dimensions above are the figures published on the product page. Before you issue a specification or place an order, ask us for the current technical data sheet so basin size, fixing centres and plumbing rough-in can be checked against your own drawings. We do not treat a catalogue figure as a substitute for a signed-off shop drawing.

Check 2: the wall behind the basin

A wall-hung basin carries water, a person's leaning weight and the leverage of a faucet. The substrate has to be designed for that, not assumed.

  • Timber stud walls: add solid noggin or a plywood plate at the fixing line, and set the basin outlet height before the lining goes up.
  • Masonry or concrete: confirm the anchor type and drilling method with the fixing detail on the data sheet, since surface tiles change the effective fixing depth.
  • Stud chase for the waste: the 1004B fixes to the wall by its back panel, so the wall cavity needs to take the trap and supply lines cleanly. A shallow service cavity will push the basin out from the finished line.
  • Tiled finished face: set out from the tile face, not the plasterboard. A 10 mm difference in adhesive and tile changes the projection you see in the room.

If your wall cannot be opened or reinforced, that is a legitimate reason to choose a floor-standing option instead of forcing a wall-hung unit into an unsuitable substrate. We would rather flag that at quotation stage than during installation.

Check 3: glaze quality in a building that gets heavy use

In a villa with weekend guests, or a boutique property where the same bathroom is used twenty times a day, the glaze does most of the work. The 1004B's dense glazed layer is described as resisting water stain and limescale build-up, which matters in hard-water regions: scale that bonds to a porous surface needs abrasive cleaning, and abrasive cleaning dulls the shine you specified.

A practical test on any sample: run your fingernail across the glaze near an inside corner. A smooth, continuous surface with no pinholes or dull patches cleans easily. Ask for a physical sample before ordering in volume — photographs will not tell you this.

Check 4: buy the series, not the item

The most common coordination failure we see is a project that specifies basins from one range, water closets from another and a bidet from a third. The shapes rarely agree, and the difference becomes obvious in every photograph of the finished bathroom.

Model 1004B belongs to the 1004 sanitary series, so matching pieces are already defined:

PieceSeries itemWhere it fits in a villa
Wall-hung basin Wall Hung Ceramic Basin 1004B Guest bathrooms, cloakrooms, ensuites where floor space is tight.
Pedestal basin Freestanding Ceramic Pedestal Basin 1004S Bathrooms where the wall cannot be reinforced for a wall-hung unit, or where pipework must be concealed by a pedestal instead of a cavity.
Toilet Washdown One Piece Toilet 1004A Listed with dual rough-in options — P-trap wall drain and S-trap floor drain — so the same model can serve bathrooms built on different drainage layouts.
Bidet Wall Hung Bidet 1004F Main ensuites and guest bathrooms where a separate hygiene fixture is part of the brief.

Ordering the series together also means one glaze batch, one delivery window and one set of spares on the shelf afterwards — small things that save real time during the defects period.

Check 5: what to send us with your enquiry

A quotation comes back faster and more accurately when the enquiry includes:

  • The quantity per bathroom type, and how many of each type the villa has.
  • A marked-up plan or elevation showing finished floor levels and the intended basin height.
  • Your drainage arrangement — wall drain or floor drain — with rough-in dimensions.
  • Faucet choice: deck-mounted single mixer or wall spout with concealed body.
  • Delivery destination and whether you want the ceramics consolidated with other fixtures in one shipment.

As a China-based manufacturer of furniture and building materials, we supply these ceramics as part of a wider fit-out package — interior fixtures, cabinetry, lighting, wall and floor finishes — so a villa project can place one order across categories instead of chasing several suppliers through the same programme.

Send us your bathroom schedule. We will check the 1004 series against your rough-in dimensions, confirm the current technical data sheet, and quote the full set — basins, water closets and matching pieces — for your villa or hospitality project. Enquiries are handled Monday to Saturday, with a reply within 24 hours.