A swim spa shell arrives on site looking unharmed and still fails to start up. The cause is rarely the moulded acrylic shell itself. It is usually what happened inside the packaging: a pump bracket that shifted in transit, a control panel with no moisture barrier, or a crate whose base does not match the forklift route at the delivery address. Before you place an order for Outdoor Swim Spa WS-115Fⅳ, treat packaging as a line item to be specified in writing, not left to the factory's default habit.
Catalogue reference for this model: WS-115Fⅳ, 5000 × 2200 × 1250 mm, control system 1 set, swim training system 1 set, water pump 1 pc, filter pump 1 pc, jets 24 pcs, LED lights 4 pcs, total power 8.05 kW. These are the figures published on the product page and they drive every packaging decision below. Confirm them again against your own signed configuration sheet, because options change what has to travel in the crate.
Why this model is more sensitive to packing than a smaller spa
The WS-115Fⅳ combines a five-metre shell with an installed swim training system and a 24-jet plumbing layout. That means more rigid pipework, more fixing points and a longer span that has to be supported along its whole length rather than at two corners. A crate designed for a short plunge spa will let the mid-span of a 5000 mm shell carry load it was never meant to take.
The electrical side adds another risk. The total power figure on the page is 8.05 kW, and that load sits behind a control system plus pumps that are usually shipped loose or partially fitted. Every one of those components needs its own restraint inside the crate and its own protection against condensation during a long sea passage.
Ask for the packing list before production starts, not after
A supplier who works on turnkey projects is used to handling several product groups in one shipment, and that is exactly when a swim spa gets packed as an afterthought. Request the draft packing list while the configuration sheet is still open for edits. It should state:
- the number of packages and the outer dimensions and gross weight of each, so you can check them against your site access and lifting gear;
- which parts travel inside the shell crate and which travel separately — control system, water pump, filter pump, swim training unit, steps and any heat pump or sand filtration option are each their own handling risk;
- the internal fixings: cradle or saddle supports under the shell, blocking at the frame corners, and how loose pumps and the control panel are anchored;
- moisture protection for the electrical items — sealed barrier bags with desiccant, not just a layer of foam sheet.
If the packing list arrives after the goods are finished, you have lost your chance to change it without cost.
Match the crate base to the delivery route and the lifting method
Write down how the spa will actually reach its final position, then send that description to the supplier. A villa pool deck, a rooftop terrace and a resort garden each create different constraints:
- Forklift or pallet jack: the crate needs skid runners at a height and spacing your machine can use, and the base must extend under the full shell length so the load is not point-supported.
- Crane or hiab lift: ask for rated lifting points or slings designed into the crate, and confirm the marked gross weight includes the packing itself.
- Manual route through a gate or side passage: check the crate's outer width against the narrowest point of the route before it is built, since an oversized crate cannot be trimmed on site without losing its structural value.
SANTERSON lists packaging and container loading as part of its logistics and door-to-door delivery service, so the crate specification and the loading plan should come from the same person. Ask that both are confirmed against your site photos or access drawing.
Decide the container plan around the electrical components
A 5000 mm shell plus its accessories is a heavy, awkward load, and how it shares a container matters. Confirm with your supplier:
- whether the spa travels alone or consolidated with other goods from the same order, and if consolidated, what sits on top of it — no loose cabinetry or stone panels should bear on a shell crate;
- how the crate is lashed and blocked inside the container, and whether dunnage bags or timber bracing are used;
- whether control panels and pumps ship in the same container as the shell, so that nothing critical is delayed by a separate consignment;
- cargo insurance cover for the packed value, and who bears risk at each leg.
Ask for photographs of the finished packing and of the loaded container before the doors are sealed. That single step settles most disputes later, because you have a dated record of the condition in which the goods left the factory.
Documentation that has to agree with the crate
Customs paperwork and the physical packages must say the same thing. The commercial invoice, packing list and any certificate of origin should show identical package counts, weights and markings, and each crate should carry a visible mark tying it to the order and to the component inside — "shell", "control system", "pumps and swim unit", "steps". When crates arrive unlabelled at a busy site, components go missing and installation stalls.
Inspection on arrival: five minutes that protects the warranty claim
- Photograph the crate before and during de-crating, including any broken bracing or shifted contents.
- Check the shell for hairline stress marks at the support contact points along its length.
- Open every electrical bag on site: look for desiccant condition and corrosion on terminals before the spa is energised.
- Count loose hardware against the packing list in front of the delivery driver, and note shortages on the delivery document.
- Report damage the same day with the photographs attached, rather than after installation has begun.
SANTERSON's installation and after-sales support covers inspection and snags on site, but the evidence you gather at delivery is what makes a claim straightforward.
A short confirmation list to paste into your purchase order: crate outer dimensions and gross weight per package; packing list approved before production; full-length cradle support for the 5000 mm shell; separate restraint and moisture barrier for control system, water pump, filter pump and swim training unit; lifting method confirmed against site access; lashing and dunnage inside the container; pre-shipping photos of packed goods and loaded container; crate markings naming each component; matching package counts on invoice, packing list and certificate of origin. If your project also needs other pool products, compare options in the swimming pools and swim spas range and ask for the same packing detail on each.
Packaging is not a favour the factory does for you. It is a specification, and like the jet count or the power figure, it should be written down, approved before production and checked at delivery.