Integrated door and paneling schemes look simple on a drawing: one continuous wall surface, with a doorway that disappears into it. In practice they sit at the meeting point of joinery, wall finish, ironmongery and site tolerance — which is exactly where quotations diverge and where projects pick up extra cost. If you are comparing suppliers for a villa or residential bathroom fit-out, here is what to put side by side before you place an order.

1. Whether the supplier is quoting one system or three trades

The most common quotation gap is scope. A paneling contractor supplies wall panels, a door supplier supplies a leaf and frame, and the site builder reconciles the two on the day. Every handover between those parties adds contingency that the buyer still pays for.

Our Integrated Door & Paneling is supplied as a single made-to-measure item within the Custom Partitions & Paneling collection, so the panel field, the door and its finish come from one production run under one drawing set. When you compare suppliers, ask explicitly: does this price cover the panels, the door leaf, the frame, the finishing trims and the opening detail — or only some of them?

Integrated door set into matching wall paneling for a residential bathroom project

Santerson Integrated Door & Paneling — made-to-measure sizing, material and finish options, layout tailored to the project.

2. How the flush detail is actually achieved

"Flush" can mean several different build-ups, and they do not cost the same. Ask each supplier to state which of these they are quoting: a door aligned with the wall face on one side only; a double-flush detail where both faces sit level; a concealed frame with hidden hinges; or a handleless opening that removes hardware from the visible face entirely.

This matters because the detailing drives what else you must buy. Concealed hinges and pivot hardware have load ratings tied to leaf weight, and a heavy veneer leaf on light-duty hinges will sag within a few years of use. Where a project needs doors that read as part of the wall from both sides, we supply them from the same collection as Flush Wall Aligned Doors and Decorative Concealed Doors, so the wall finish and the door face are specified together rather than matched after the fact.

3. Finish continuity across materials, not just colour

A sample chip that matches under shop lighting can still read as a different surface once it is installed at scale, because grain direction, sheen level and joint pattern all change how a finish behaves over a large panel field. Compare these four points across your quotes:

  • —Sheen level stated numerically or by name, not "matching matt".
  • —Grain or pattern direction across the panel run, and whether joints are shadow-gap or butt.
  • —The substrate behind the finish, which determines how the panel takes humidity in a bathroom.
  • —Whether the door face and the wall panels are produced from the same batch of material.

Where a scheme mixes materials, we can carry the same logic into Textured Panels, Matte Lacquer Panels and Stone & Marble Panels, so the wall specification stays consistent from the doorway to the rest of the room.

4. What is measured on site, and by whom

Integrated openings fail most often on tolerance, not design. Panel runs need a true wall; concealed frames need the correct floor-to-finished-floor dimension; and a doorway that has been set out before the screed level is fixed will not close cleanly afterwards.

Before you sign any purchase order, confirm three things in writing: who takes the site dimensions, at what construction stage they are taken, and what happens if the opening on site differs from the drawing. Our product pages list made-to-measure sizing with layout tailored to the project, and we ask buyers to confirm dimensions and selected specifications for each project before production starts.

If your supplier does not name a survey stage, assume you will be carrying the rework cost yourself.

5. What travels with the goods and who installs them

Paneling is bulky, and edges are where damage happens. Ask how panels are crated, whether the door leaves travel assembled or loose, and how the shipment is packed for container loading. Then ask who fits them. A concealed-frame door installed by a general carpenter who has not used that hardware before is a common source of snags at handover.

We handle this as part of the same engagement as production: freight arranged to site, then installation support with inspection and snagging at handover. For buyers comparing SANTERSON against a local joinery workshop, this is usually where the real difference in project cost appears — not in the unit rate.

A practical comparison sheet

Point to compareQuestion to ask each supplier
Scope of supplyPanels, leaf, frame, trims and opening detail in one price — or split across suppliers?
Flush detailSingle-face or double-flush; concealed or exposed frame; handleless or hardware on show?
Hardware ratingHinge and pivot load ratings against the finished leaf weight and size.
Finish specificationNamed sheen level, grain direction, joint type, and same-batch material for door and panels.
Substrate suitabilityWhat sits behind the finish in a wet area, and how it is detailed at the floor and ceiling lines.
Survey stageWho measures, when, and who carries the cost if site dimensions differ from the drawing.
Packing and freightCrating method, edge protection, assembled or loose leaves, container loading plan.
Fitting and snaggingWho installs the concealed hardware, and what inspection happens before handover.

Use your own project drawings when you send this sheet out — suppliers quote far more accurately against a marked-up opening than against a product name.

Where the rest of the wall fits in

Doors and paneling are rarely an isolated purchase. Once the opening detail is settled, the same drawing set usually has to absorb display niches, service access and storage. We design those into the same run: Custom Niche Paneling for recessed display and shelving, and Wall Panel Systems where the panel field extends across whole rooms rather than a single feature wall. Buying those elements against one coordinated specification avoids the small mismatches — differing skirting details, inconsistent reveal depths — that show up when each item is ordered separately.

If you have drawings for a villa or residential bathroom project, send us the openings and the finish schedule. We will confirm what can be produced as one integrated door and paneling package, where the site survey needs to happen, and what the whole scope costs before anything goes into production.