A swim spa is one of the heaviest, most equipment-dense items in a villa or resort order. The Outdoor Swim Spa WS-115AⅢ arrives as a single moulded shell carrying pumps, jets, lighting and controls, so the difference between a smooth handover and a stalled site usually comes down to decisions made before production starts — not after the container is sealed. This guide walks through the planning sequence we follow for international project orders of this model.

Start with the shell, not the shipping date

The WS-115AⅢ has catalog dimensions of 3880 × 2200 × 1250 mm. Treat those numbers as the design input for the whole delivery chain: the access route from the street to the pad, the door and gate widths on site, the turning space at the placement point, and the lifting or walking plan once the spa is off the truck. A shell that fits the plot but not the pathway becomes a crane hire nobody budgeted for.

Send us the site plan and the intended placement location with your enquiry. We check the access route against the packaged dimensions and confirm whether the spa can be walked in, tipped in, or needs lifting equipment, so the local arrangements are booked while production is still running.

Confirm the configuration before it is packed

The catalog listing for this model shows a control system, swim training system, water pump, filter pump, 24 jets and 4 LED lights, with total power shown as 8.05 kW. Those figures describe one configuration. Optional items in the range include heat pumps, UV sterilisation, additional water pumps, sand filtration, insulation and steps — and adding or removing equipment changes both the electrical load and the packing list.

Two points matter for an international order:

  • Electrical match. Supply voltage, phase and protection in the destination country must match what the control system, pumps and any heat pump are built to. Confirm this with your electrician before the configuration is fixed, and keep the same specification on the purchase order, the packing list and the invoice.
  • Site services. Foundation or support pads, drainage, insulation in cold-climate installations and steps all sit outside the factory scope but decide whether the spa can be commissioned on the day it is placed. We flag these items during order confirmation rather than at delivery.

Choose the freight mode against the site programme

As part of our logistics and door-to-door delivery service, project orders move by sea, air or rail freight forwarding, with customs paperwork prepared alongside the shipment. For a full container order combining a swim spa with other fit-out items, consolidation is usually the practical option: the spa, outdoor furniture and interior fixtures travel together on a single set of documents, which means one clearance event and one delivery window instead of several.

For a single spa ordered on its own, we advise on whether a shared container or a dedicated one is better for your port and site access. Transit time, import duty treatment and Incoterms differ case by case, so the terms are agreed in writing with your procurement contact before production begins — not inferred from marketing pages.

Packaging and loading are engineering decisions

A moulded acrylic shell under tension can crack at a support point, so the spa is packed on a rigid base with the shell supported along its length, protective interlayers for the shell surface and jet fittings, and loose equipment — control system, pumps, lighting, spares — crated separately and labelled against the packing list. Container loading is planned around the shell's footprint so it is blocked and braced, not wedged.

Before the doors close we send you photographs of the packed spa and the loaded container, together with the packing list showing every crate. Unloading crews on site can then work from the same document, and any shortage or damage claim starts from a documented condition at origin.

Documentation that clears customs without delay

Most clearance delays come from paperwork, not cargo. For an international order we prepare the commercial invoice, packing list and certificate of origin, and support import permits where the destination requires them. Consistency is what matters: model name, quantity, power rating and value must read the same way on every document and match the purchase order.

If your project has a nominated customs broker, we work to their format so the declaration matches local requirements. Cargo insurance can be arranged for the ocean leg when the project programme cannot absorb a claim cycle.

Plan the last mile and commissioning

Delivery to the port is not completion. Before dispatch we agree with you who handles offloading at site, which equipment is needed for placement, and what has to be ready on the ground — pad cured, drainage connected, power feed terminated, and a clean, level working area around the installation point. Where the project needs it, our installation and after-sales support covers site guidance, inspection of the delivered units and follow-up on spares.

A short commissioning check follows placement: power-on sequence, control system operation, pump and jet function, filtration cycle, and a leak check at joints and fittings. Anything unresolved is recorded as a snag list against the order rather than left to site conversation.

Ordering it as part of a wider project package

Swim spas rarely appear alone in a project bill of quantities. When the spa is ordered through our custom and OEM service alongside other scope — poolside loungers, pergolas, outdoor dining sets, bathroom ceramics, lighting or cabinetry — one project coordinator tracks the full set of dimensions, configurations and delivery windows, so the spa is not the item that holds the site programme hostage.

The same coordination applies to specification work. If a project needs a different length, jet layout or equipment package, we review it against the swim and hydrotherapy range before quoting, rather than promising something the shell cannot carry.

A practical pre-order checklist

  • Site plan, access route and placement point, checked against 3880 × 2200 × 1250 mm packaged dimensions.
  • Confirmed equipment list for the chosen configuration, including heat pump, insulation and steps if required.
  • Destination supply voltage, phase and protection confirmed by the site electrician.
  • Agreed Incoterms, freight mode, port of delivery and named site delivery address.
  • Documentation set agreed with your broker: invoice, packing list, certificate of origin, permits.
  • Offloading and placement plan on site, including lifting equipment if the route requires it.
  • Commissioning responsibility and snag process written into the order.

Send the site drawings and your required configuration to our project team and we will return a delivery plan for the WS-115AⅢ with the packaging, documents and site responsibilities set out before production starts. Explore the full swimming pool collection for alternative lengths and equipment packages.