A swim spa quotation goes wrong in two directions. Too little detail and every supplier prices a different product, so the numbers never line up. Too much unverified detail and you end up approving a specification nobody can build or site. The Outdoor Swim Spa WS-S08T1 / WS-S08T2 sits right in that territory: a long shell combining a swim training system with a jetted hydrotherapy section, listed as a configurable model pair rather than a fixed catalogue item. This guide sets out what a buyer should hand to a manufacturer before a quotation is requested, so the specification, the equipment list and the site conditions all arrive in one conversation instead of across six email rounds.

Start From the Model Pair, Not a Single Model Number

The catalog lists two models under one listing, WS-S08T1 and WS-S08T2, at 7800 × 2200 × 1500 mm. Treat the pair as a configuration family: the shell envelope is shared, while equipment count, options and finish are set per project. Stating only "S08" in an enquiry invites assumptions about which variant you mean, and that is where jet counts, pump sizing and power figures start drifting between quotations.

Write the model designation exactly as it appears on the product listing, then state what you are buying it for — a private villa pool deck, a resort or hotel outdoor wellness area, or a residential development where several identical units repeat. Repeat quantity matters in a configurable build: it changes how much detail is worth locking down and whether an option such as a heat pump or sand filtration is better specified once for the whole order.

Confirm the Catalog Specification Before You Change Anything

The published specification gives you a starting point to react to rather than a blank sheet. Use it as the baseline in your brief and mark only the lines where you genuinely need a deviation.

Item listedCatalog figureWhat to state in your brief
Shell envelope7800 × 2200 × 1500 mmAvailable site length, width and clear height, including access route from the delivery point
Swim training system1 setIntended use: lap swimming, guest fitness, rehabilitation or hydrotherapy-led programming
Water pumps / filter pump2 water pumps, 1 filter pumpWhether the swim and spa sections run on separate circuits, and where plant access is needed for service
Jet total50 jetsJet layout preference by zone, and whether any seating position needs a dedicated jet group
Lighting4 LED lights, 28 small LED lightsDesired lighting zones and control grouping, matched to the surrounding landscape lighting
Water treatmentOzone systemLocal disinfection requirements and your maintenance routine for the operator who will run the unit
Control system1 setWho operates it — owner, facilities team or building management — and where the controller should sit
Total power9.55 kWAvailable supply capacity, phase and protection at the installation point, plus electrical routing

One habit saves rework: quote the figures back as catalog values and ask the manufacturer to confirm them for the configuration you are ordering. Equipment counts and power totals move with options, so a specification that is only correct for one variant will not describe your delivered unit.

Decide Which Options Belong in the Order

Options listed for this range include control systems, UV sterilization, water pumps, heat pumps, sand filtration, insulation and steps. Each one is a decision with a site consequence, so it is better resolved before the quotation than during production.

  • Heat pump and insulation. Relevant whenever water temperature has to hold across a shoulder season or overnight. State the ambient conditions at the site and the target water temperature; the manufacturer can then say which combination is being proposed rather than leaving it implied.
  • UV sterilization alongside ozone. Relevant where a unit sees heavy daily use, such as a hotel or resort wellness area. Ask what the maintenance interval is and who supplies consumables.
  • Sand filtration versus the listed filter pump arrangement. Affects plant footprint and backwash arrangements, so it needs to be settled alongside the plumbing route.
  • Steps and access. Entry position determines circulation on the deck and whether the step is at the swim end or the spa end. Decide from how people will actually move around the space.

Availability and compatibility of these options vary by model, so a shortlist with a written confirmation for each line is worth more than a long wish list attached to an enquiry.

Send the Site Conditions With the Enquiry

Most delays in a custom outdoor swim spa order trace back to site information arriving late. Include the following with the enquiry and the manufacturer can price realistically instead of adding caveats:

  • Dimensioned plan of the intended position, with the delivery access route and any overhead restriction on that route.
  • Structural information for the supporting surface or recess, including whether the unit is above ground, semi-recessed or fully recessed.
  • Electrical supply details at the installation point: capacity, phase, protection device and cable route.
  • Drainage and overflow arrangement, plus where backwash or drain water is permitted to go.
  • Local consent or inspection requirements you have already identified, and who is responsible for meeting them.
  • Your programme dates — site-ready date and required arrival window.

If the swim spa is part of a wider fit-out, say so. A unit coordinated with turnkey project solutions can be scheduled alongside decking, lighting, cabinetry and outdoor furniture in one production and shipping plan, which removes the sequencing problem of a shell arriving before the base that supports it.

Agree the Working Method Before Production Starts

A configurable unit needs sign-off points. The cooperation steps described for interior design services run from project brief and design proposal through quotation and detail confirmation to production, shipment and follow-up. Ask for the same sequence in writing, with named deliverables at each stage: a confirmed specification sheet, an equipment list with quantities, a dimensioned drawing showing service access, and a packing list before despatch.

Where you need something outside the listed configuration — a finish detail, a branding element on the control panel, or a unit matched to an existing deck module — that is the point at which custom and OEM service becomes relevant. Bring reference drawings rather than photographs alone; a dimensioned sketch in millimetres prevents the interpretation gap that photos create.

Freight deserves the same attention as the product. The logistics and door-to-door delivery arrangements cover sea, air and rail forwarding with customs paperwork, packaging and container loading. Confirm the Incoterms being quoted, who handles clearance at destination, and how the unit is packaged and lifted on site. A shell of this length is not a small parcel, and the unloading method belongs in the plan before it arrives.

Close Out With Installation and Spares

Ask what happens after delivery. The installation and after-sales support service covers on-site installation, inspection and snags, warranty coverage, spare parts and ongoing maintenance. Before ordering, get clarity on three things: which consumables and wear parts you should stock, what the warranty terms and exclusions actually are for wet components and electrical equipment, and how a fault is reported and supported once the unit is in service.

For a unit run by site staff in a hospitality setting, also request commissioning documentation your facilities team can actually use: as-built equipment list, wiring schedule, chemical dosing guidance for the specified treatment system, and a maintenance interval table.

A Practical Test Before You Send the Brief

Send your enquiry to two or three suppliers and compare the questions that come back. If nobody asks about supply capacity, access route or circuit arrangement, your brief is missing information that determines price. A supplier who raises those points in the first round is working from the same specification you are.

Where This Model Sits in the Range

If your site length or programme does not suit a shell of this size, compare against the wider swimming pools and swim spas range before committing to a specification. Envelope size, jet count and equipment set change across the range, and selecting the right starting model costs less than modifying one later. SANTERSON has operated since 2008 as a China-based manufacturer and one-stop furniture and building materials supplier for villa, hospitality and office projects, covering design coordination, production, delivery and installation support.

Specification values quoted above are transcribed from the published catalog listing for WS-S08T1 / WS-S08T2. Included equipment, electrical requirements and option compatibility vary by configuration and should be confirmed in writing for the unit being ordered.