A high gloss lacquer wardrobe can look identical in two quotations and still behave very differently once it is installed, checked at handover, or hit by daily use. The difference rarely shows up in the render. It shows up in the sample you asked for and in the line items you insisted on seeing before the order was placed. If you are buying built-in joinery for a residence, a serviced-apartment fit-out or a villa project, this guide walks through what to put in front of you when you compare samples and proposals.
Start With the Reference You Are Actually Buying
Before any sample is requested, fix the reference. Suppliers describe gloss surfaces in loose language: lacquer, lacquered, high sheen, piano finish. Those words are not interchangeable across factories. Ask which named product line the quotation refers to, then read the specification against that page rather than against your mental image. Our own High Gloss Lacquer Wardrobes sit in the Lacquer Wardrobes collection, and the published specification for that line is deliberately open: made-to-measure sizing, material and finish options, and a layout tailored to the project. That openness is a feature, but it also means the quotation you receive is only as precise as the details you asked it to carry.
Do the same for the alternatives on your shortlist. A High Gloss Sliding Door Wardrobes proposal and a hinged lacquered wardrobe proposal are not comparable on price per linear metre alone, because the door system changes the carcass tolerance, the clearance you need in front of the opening, and how much of the gloss panel is exposed to knocks.
What a Useful Sample Actually Proves
A colour chip tells you almost nothing about a gloss surface. Request a panel sample large enough to judge reflection, something in the region of an A4 sheet or bigger, made on the same substrate and with the same edge treatment that will be used on your doors. Then test it rather than look at it.
- Judge the reflection under your own lighting. Move the sample into the room, or replicate the room's colour temperature and lighting level. Gloss finishes read warm under 2700K and hard under 4000K; a swatch photographed on a light box will not predict either.
- Inspect the edge, not just the face. Turn the sample over and look at how the surface wraps or is lipped. On a wardrobe door the edge line is where quality differences become visible from a normal viewing distance.
- Check the return of the sheen after pressure. Press a thumbnail firmly into a corner of the sample and watch whether the mark recovers. This is a rough, honest test of surface hardness that no data sheet substitutes for.
- Compare the same colour across two suppliers side by side. Metamerism is real: two samples that match individually can disagree badly under one light source. Put them next to each other before you sign anything.
Read the Proposal as a Specification, Not a Price
Once you have physical samples from two or three sources, compare the paperwork on the same terms. The table below is the comparison sheet to build; fill it in for every quotation and reject any proposal that leaves a row blank.
| Line item | Why it matters | What a serious proposal states |
|---|---|---|
| Substrate and thickness | Drives flatness, hinge holding and door sag over a tall wardrobe front. | Named board type and thickness for doors and carcass separately. |
| Surface build-up | Determines depth of reflection and resistance to marring. | Whether the gloss is applied as a panel laminate or built up in coats, and how many. |
| Edge method | The most visible failure point on gloss doors. | Wrapped, lipped or solid-edge construction, plus the adhesive or process used. |
| Door system and hardware | Hinged, sliding or pocket operation changes clearances and load. | Named runner, hinge and soft-close specification with duty rating. |
| Carcass tolerances | Affects scribe allowance on uneven walls and ceilings. | Finished versus rough opening dimensions and the scribe plan. |
| Interior configuration | Where most change requests appear after order confirmation. | Shelf, drawer, hanging and lighting layout drawn, not listed in prose. |
| Scope of supply | Decides whether you are comparing wardrobes or wardrobes plus delivery and fitting. | Explicit split between manufacture, packing, freight, and installation. |
| Change control | The single largest source of cost drift on joinery packages. | Written cut-off point for dimension and layout changes after production release. |
Two proposals that differ by 15% are usually not a price argument; they are a scope argument. The cheaper quotation has typically moved one of the rows above out of its own column and into yours.
Where Gloss Lacquer Goes Wrong on Site
Most complaints about high gloss joinery are installation complaints wearing a finish label. Three failures recur:
- Floor and ceiling levels taken on trust. Gloss doors with a tight reveal show every millimetre of out-of-level. Ask for the survey method: laser level, which datum was used, and who signed off the finished floor height before the wardrobe was measured.
- Protection removed too early. Gloss panels are usually delivered with a protective film. On an active site that film is scraped off by other trades long before handover. Agree in writing who protects the fronts between installation and practical completion.
- Cleaning instructions never issued. Abrasive cloths and ammonia-based cleaners haze a gloss surface permanently. Request the cleaning method with the delivery paperwork, not after the first mark appears.
A practical test for any supplier: ask them to show one completed wardrobe they supplied, photographed at handover rather than in a showroom, and to describe the trades that worked around it. Suppliers who run their own project coordination can answer this immediately. Suppliers who only sell panels cannot.
Comparing Single-Item Quotes Against a Coordinated Package
Wardrobes rarely sit alone. In a villa or apartment fit-out they share a wall with doors, skirting and sometimes cladding, and they face a floor that has to be ordered months earlier. Comparing one wardrobe quotation against another therefore undervalues a real cost: coordination.
If you are sourcing several finishes for the same building, price the package as well as the item. A built-in furniture line ordered alongside flooring, wall panelling and joinery from one source gives you a single tolerance conversation instead of four. Where that coordination sits with the supplier, as part of turnkey project furnishing, the comparison should include design coordination, production sequencing and site support, not only the unit rate.
The Comparison Checklist Before You Sign
- Physical gloss sample in hand, judged under the room's own lighting, with edges inspected.
- Named product line and collection cited on the quotation, not a generic finish description.
- Substrate, thickness, surface build-up and edge method stated for doors and carcass separately.
- Door system, hardware specification and duty rating stated; clearances confirmed against the room.
- Survey method and datum recorded; finished floor level confirmed before measurement.
- Interior layout supplied as a drawing with shelf, drawer, hanging and lighting positions.
- Scope split in writing: manufacture, packing, freight, installation, protection until handover.
- Change-control cut-off stated, with the cost basis for changes after production release.
- Cleaning and maintenance instructions committed to the delivery pack.
Frequently Asked Questions
Should I ask for samples from every supplier on the shortlist?
Only after you have narrowed to two or three by specification. Panels of gloss material are costly to produce and ship, so use the paperwork comparison first and reserve sampling for the finalists.
Is a made-to-measure wardrobe always more expensive than a modular one?
Not necessarily. Made-to-measure sizing removes wasted height and depth, which on a full-height wall can offset the extra fabrication. Compare cost per usable storage volume, not cost per metre of frontage.
How do I compare gloss levels objectively?
Ask each supplier for the sheen band they supply and request it in writing, then verify by eye against a single reference panel under one light source. Numbers alone across different factories are not directly comparable; a physical side-by-side is.
What should I do if two samples match in the showroom but not at home?
That is metamerism, and it is normal. Put both samples against a fixed grey card under the room's own lamp, at the same time of day, and choose the one that holds its tone across daylight and artificial light rather than the one that looks richer on the day you received it.
Can I order wardrobe doors and carcass from different suppliers?
You can, but you inherit the tolerance conversation yourself. If you do, insist that one party signs off the finished opening dimensions in writing, because that is where the two packages disagree.
If you want a specification reviewed before you commit, send the drawing and the two competing quotations. We will tell you plainly which line items are missing and what they will cost you later. That review costs nothing, and it usually saves an argument at handover.
Send your drawings for review
WhatsApp: +86-13928214007 (PHILLIP)
Email: santerson@qq.com
Or use our contact page.