A shaker front is one of the safest door styles in a project kitchen: a flat centre panel framed by a square rebate, quiet enough to sit in a coastal villa or a serviced-apartment block without fighting the rest of the interior. The question for a buyer is rarely whether the style works. It is whether this particular combination — a shaker profile with a PVC-based cabinet build and made-to-measure sizing — belongs on your bill of quantities at all, and at which point in the programme you should commit to it.
Below is how we would read that decision from the procurement side, using our shaker style kitchen cabinet line as the worked example.
1. When the room is being built around the cabinetry, not the other way round
Stock carcasses make sense when a plan was drawn to a module grid and the walls land where the drawings say they should. Project work rarely behaves that way. Site-built reveals move, services get relocated late, and an appliance schedule written before the builder arrives is often out of date by the time cabinetry is measured.
Our shaker cabinets are supplied as made-to-measure work: sizing to the actual opening, material and finish chosen per project, and a layout drawn for the space rather than fitted into it. That becomes the right route when:
- the run includes returns, alcoves or ceiling-height units that no standard module fills cleanly;
- appliances are being integrated into tall housings, so carcass depth and ventilation clearance have to be set around the machine;
- several units or villas in one development share a design intent but differ in plan dimensions;
- the same door profile has to continue into wardrobes, laundry joinery or media walls, so one shop drawing governs the whole apartment.
For a single flat with straight walls and standard appliances, buying off the shelf is usually cheaper. For a multi-unit job or a villa where the kitchen carries the interior language, custom work removes the site adjustments that otherwise appear as variations.
2. When moisture and cleaning frequency drive the specification
Kitchen cabinetry fails at the edges first — door perimeters, splashback junctions, the zone under the sink. In a rental, a serviced apartment or a guest kitchenette, that edge is being wiped daily with whatever the cleaning team has on hand, not with a care sheet.
A PVC-based cabinet build in the shaker profile is the version we would put forward for those rooms, because the door face and its profile are one continuous wrapped surface rather than a moulded part with a visible joint to seal. Where the same kitchen sits outdoors or under a covered terrace, we would move the specification across to our outdoor ready PVC cabinets and have that reviewed separately; the exposure conditions are different enough that the door build should not be assumed.
One honest caveat. The catalogue entry for this line carries both "PVC" and "plywood" in its page naming, so the board behind the door depends on which version of the range you are quoting. Do not lock a material description into a specification document from a product title alone — ask us for the written construction build-up for your order, and check it against the finish sample before sign-off.
3. When the shaker front has to hold a colour across a whole development
Shaker doors read as one surface from a distance and two surfaces up close, which is exactly where colour drift becomes visible. A grey that looks correct in a showroom door looks wrong when three apartments each arrived with a slightly different tone.
Buying the profile custom lets you set the finish once and repeat it: matte, gloss or wood-effect surfaces across the same tooling, with the frame and centre panel drawn from the same batch. If your palette sits in the softer neutrals, our grey shaker cabinets are the reference point; if it runs to a warmer wood grain against white carcasses, our matte PVC kitchen cabinets cover that combination. Either way, approve a physical door sample before the production run, not a screen render.
4. When one supplier should carry more than the kitchen
The heavier cost in project joinery is usually coordination, not boards. Separate shops for kitchen, wardrobes, vanities and wall panelling means three sets of drawings, three tolerance habits, and three rounds of site measurement.
This is where a one-stop furniture and building materials supplier earns its place on the schedule. Santerson is a China-based manufacturer supplying cabinetry alongside flooring, doors, wall and ceiling panels, lighting, ceramics and outdoor furniture for villa, hospitality and office projects, with custom and OEM work handled in-house. When the kitchen, the bedroom joinery and the matching internal doors come from one drawing set, rebate depths and reveal lines match on site.
That scope also covers the parts buyers usually chase separately: freight forwarding and door-to-door delivery, then installation and after-sales support at destination. Confirm the commercial terms — Incoterms, duties, insurance and the exact delivery line — for your country in writing; published service descriptions are not a substitute for a quotation.
5. When to commit to custom work in the programme
Custom cabinetry is only an advantage if it is instructed early enough to be drawn once. The point to place the order is after the appliance schedule and service positions are fixed, and before wall finishes are set — so the carcass dimensions drive the tiling setting-out rather than following it.
Before we can price it properly, send us:
- measured drawings or a marked-up plan for each unit type;
- the appliance list with model dimensions and whether each is integrated;
- countertop material and edge detail, since the worktop sets carcass height;
- the door finish you want matched, ideally with a sample reference;
- quantities by unit type, and your destination port or site.
With those five items we can return drawings for approval and hold the profile, colour and carcass build constant across every unit in the job. Send them through our contact page and we will confirm construction details, dimensions and finish options for your project before production starts.