A wood tone open wardrobe looks simple on a drawing: hanging rails, shelves, drawers, no doors. That is exactly where the trouble starts. With nothing to close over the carcass, every edge, every shelf depth and every grain match sits in plain view. Before an order goes into production, buyers should walk through the decisions below with their supplier, because most of them cannot be corrected after the panels are cut.

What to settle before production: overall dimensions against the finished floor and ceiling levels; which substrate and wood tone finish you are specifying; how the open frame will be fixed and supported; the internal layout for the actual wardrobe contents; storage for loose items that still need hiding; lighting and cable routes; edge treatment where panels meet walls and ceilings; and who measures, delivers and installs.

Why an Open Wardrobe Exposes Every Compromise

A closed wardrobe lets you put a modest carcass behind a good-looking door. An open one does not. The same panel that carries the clothes is also the visible surface, so substrate quality, edge banding, and how the wood tone wraps around corners all become part of the appearance rather than something hidden. Dust, too, settles on hanging garments and shelves, which changes how often the piece needs cleaning and how you want the top of the unit finished.

The other difference is tolerance. A door can absorb a few millimetres of out-of-plumb wall; an open run cannot, because the side panel is seen against that wall from floor to ceiling. This is why we ask for dimensions taken off the finished surfaces, not the structural shell, and why we confirm them again before cutting.

Dimensions: What to Measure and When

Our Open Wardrobes are made to measure, with layout and finish specified per project. For a wood tone open wardrobe, send the supplier the following rather than a single width and height:

  • Width, height and depth at three points each — top, middle and bottom — measured after the final floor covering and ceiling finish are in place.
  • The plumb and level condition of the wall the carcass sits against, and whether there is a skirting board to scribe around or remove.
  • Position of switches, sockets, air grilles, downlights and curtain recesses that fall inside the wardrobe zone.
  • Doorway and corridor widths at the property, plus stair or lift dimensions, so the delivery route for full-height panels is known before shipping.

If a room is being fitted out while still in construction, treat the first set of numbers as indicative and plan a re-measure once wet trades have finished. We build that re-measure into the workflow described on our interior design services page, where drawing review and production coordination sit between the brief and manufacture.

Substrate and Wood Tone Finish

"Wood tone" covers several quite different specifications, and price comparisons only work when everyone is quoting the same one. Ask your supplier which of these you are buying:

Finish routeWhat to check on the sample
Wood veneer with open grainVeneer thickness and whether the surface is brushed; how the tone reads under your own lighting rather than a showroom lamp; what happens at edges and cut-outs.
Laminate or melamine with a wood decorationWhether the edge banding matches the decoration exactly, and whether a matching post-formed or laser edge is available for visible long edges.
Painted or lacquered grain effectHow much of the grain texture remains in the finish coat, and how the surface tolerates cleaning over time.

Order a physical board sample before approving a tone. Screens shift colour, and a warm oak that suits a bedroom with north light can turn orange under warm LED strips inside a wardrobe. If the wood tone has to match existing joinery — a natural wood veneer cabinet run in the same apartment, for instance — send the supplier a sample of what already exists rather than a photograph.

We do not publish fixed board specifications across the catalogue; substrate and finish are confirmed on the drawing for each project. Ask for the written specification for your order instead of assuming a standard build.

Structure: Frame, Support and Span

With no door to stiffen the carcass, ask how the unit resists racking and how far shelves can span before they deflect under hanging clothes and folded stacks. Two structural routes appear in our range:

  • Metal frame open wardrobes, where a slim metal structure carries the load and timber-look panels slot into it. Useful when you want a light visual profile or a unit that reads as furniture rather than built-in joinery.
  • Freestanding open wardrobes, which can be moved or re-sited and are practical where the floor or wall cannot be drilled — rented property, tiled wall, or a layout still being tested.
  • Built-in runs fixed to wall and, where required, ceiling, with noggins or backing timber provided at the positions shown on your drawing. This is the route for floor-to-ceiling work and for scribing to an uneven old building.

Agree the fixing method in writing and confirm what your builder must provide: solid blocking behind plasterboard, a ceiling battens line, or a load-bearing wall. Getting this wrong is the most common cause of a site delay on open joinery.

Internal Layout Built Around What You Actually Own

Ask the supplier to lay out the interior from a list of contents, not from a generic template. The measurements worth fixing early:

  • Hanging heights: long hanging for coats and dresses, double hanging for shirts and folded tops, plus clearance above the rail so hangers do not bind.
  • Shelf depth versus shelf height — deep shelves swallow clothes in the back row unless they are shallower than the hanger depth.
  • Drawer count and whether drawers sit under hanging sections, where they need a clear pull-out path.
  • Open cubby widths for bags and boxes, and shoe shelving at a height you can reach without bending to the floor.
  • Trousers rails, valet rods and jewellery trays only if they will genuinely be used; they are easy to add on a drawing and easy to ignore in practice.

If the bedroom also needs display storage, an open wardrobe pairs naturally with open modular wardrobes in the same finish, which keeps a run of units visually consistent where a single large carcass would overwhelm the room.

Hiding the Things You Do Not Want on Show

Buyers often choose an open wardrobe for the lightness and then discover that suitcases, off-season bedding, laundry baskets and paperwork need doors after all. Resolve this in the layout rather than later with boxes:

  • A closed cabinet section or tall bank at one end of the run, in the matching wood tone.
  • Deep top storage above the hanging zone, accessed by step, for seasonal items.
  • Drawers with fronts in the same material, which read as part of the design and cover the everyday clutter.
  • Baskets and trays sized to the cubby openings you specify, so they fit rather than improvise.

Lighting, Power and Cable Routes

Open wardrobes are usually lit, because the hanging zone is the display. Decide this before panels are machined so the supplier can pre-cut channels and drillings:

  • Rail-mounted or shelf-edge LED strips, with the driver located where it stays reachable for replacement.
  • Switch type — door-adjacent switch, motion sensor, or both — and where the sensor's line of sight will actually fall.
  • Colour temperature and colour rendering specified to suit the wood tone; a strip that flatters white walls can make a warm oak look flat.
  • Cable route from the nearest supply to the wardrobe, including any wall chasing your electrician must complete before installation.

Edges, Joints and Transitions

The finish quality of an open wardrobe is judged at its edges. Ask for details on:

  • Visible long edges — banding material, radius, and whether the decoration wraps continuously.
  • Where the carcass meets wall and ceiling: scribed filler, shadow gap, or a flush trim, agreed with your builder so the plasterer knows what to prepare.
  • How a run continues into an adjacent corner — angled post, return leg, or a butt joint covered by a trims piece.
  • Cut-outs for skirting, downlights or sockets, and whether these are machined in the factory or on site.

Matching the Rest of the Room

A wood tone open wardrobe rarely stands alone. If the same finish has to carry through other joinery, place those items on one order and one drawing set so they are produced from the same batch: floating shelves, a floating TV unit, and any built-in kitchen cabinetry visible from the bedroom suite. Panels cut in separate batches can vary in tone even under the same specification, which is precisely what an open, doorless design makes obvious.

Procurement Route for a Custom Order

For buyers ordering from outside China, our workflow on this type of product runs as follows:

  • Brief and drawings. Room dimensions, photographs, floor plans and the contents list. We return a layout and elevation for review.
  • Specification confirmation. Substrate, wood tone finish, edge treatment, hardware, lighting and fixings, all shown on the approved drawing.
  • Production and quality control in our factory, with panel numbers marked for assembly.
  • Logistics. Freight by sea, air or rail, packaging and container loading, customs documentation and door-to-door delivery — see our logistics service. Confirm import terms, duties and transit time for your destination with us in writing before dispatch.
  • Installation and after-sales. On-site fitting where arranged, inspection of the completed run, and spare parts support afterwards — see installation and after-sales support.

Where a project needs pieces built to your own drawings or branding, our custom and OEM service covers bespoke finishes and materials alongside manufacturing to supplied specifications.

A Pre-Production Checklist

Confirm these in writing before your wood tone open wardrobe enters production
  • Dimensions re-measured against finished floor and ceiling levels.
  • Substrate, wood tone finish and edge banding approved from a physical sample.
  • Internal layout signed off against a written list of wardrobe contents.
  • Closed storage provision for items that should not stay on open display.
  • Fixing method agreed, with blocking or battens listed as builder's scope.
  • Lighting type, driver location, switch and cable route confirmed and machined.
  • Edge, corner and wall/ceiling transitions detailed on the drawing.
  • Matching joinery ordered together from the same batch.
  • Delivery address access, unpacking and installation responsibilities named.

Questions Worth Asking Your Supplier

  • Which board and finish specification is this price based on, and what does the upgrade to veneer cost?
  • What is the maximum unsupported shelf span in this material at this depth?
  • Are edge banding, cut-outs and machinings included or charged separately?
  • How are full-height panels brought into my property, and will they pass the stairwell or lift?
  • Who fixes the unit to the wall, and what preparation must be complete before installation day?
  • What happens if a panel is damaged in transit — replacement panel alone, or a full re-order?

If you are specifying wood tone open wardrobes for a villa, apartment or hospitality project, send us the drawings and contents list and we will return a layout, specification and quotation. As a one-stop furniture and building materials supplier, SANTERSON handles the joinery, the matching finishes and the delivery to site in one order.