A swim spa on a hotel terrace, a resort pool deck or a villa garden has to work harder than a residential one. Guests expect it to be swimmable in the morning and relaxing at night, while the owner needs a shell that fits the available slab, a power supply the site can actually deliver, and equipment that is straightforward to commission and maintain. This guide walks through how we specify the Outdoor Swim Spa WS-S06CT-L for hospitality and villa projects, and how to judge whether it is the right unit for your site.

Where this model usually fits

The Outdoor Swim Spa WS-S06CT-L is a swim spa with a hydrotherapy section, listed at 6670 × 2380 × 1400 mm. That footprint is what makes it useful on projects where a full swimming pool is out of the question: a boutique hotel courtyard, a resort terrace, a villa side yard, or a serviced apartment block with limited outdoor area.

Because the unit is manufactured as a self-contained shell rather than built in place, it suits sites where excavation and wet trades are expensive or disruptive. The two questions that decide the purchase are whether the length and width can be delivered to position — through a gate, around a pool edge, or lifted onto a terrace — and whether the electrical intake can carry the load. Both should be answered before the unit is quoted, not after.

Reading the specification as a buyer

The figures below are what we publish for this model. Treat them as the starting point for coordination with your architect and services engineer, because the final configuration changes what is actually installed.

ItemCatalogue figure for WS-S06CT-L
External dimensions6670 × 2380 × 1400 mm
Total power8.35 kW
Jet total31 pcs
Swim training system1 set
Water pump / filter pump1 pcs / 1 pc
Control system1 set
LED lights4
Features shownWater jets, temperature setting, LED lighting, ozone, swim training system

Three of those lines deserve more attention than they usually get in a tender document.

  • Total power (8.35 kW). This is the figure you hand to the electrical contractor. It drives cable sizing, protection devices, and whether an existing distribution board on a retrofit can take the circuit. If the site supply cannot carry it, that constraint has to be resolved at design stage rather than discovered at commissioning.
  • Jet total (31 pcs) with swim training system (1 set). Together these tell you the unit does two jobs: a current to swim or walk against in the morning, and massage jets for evening use. For a hotel that dual use is the argument for choosing a swim spa over a plunge pool — one asset supporting two guest programmes.
  • Temperature setting and ozone. A set temperature extends the usable season at cooler or coastal sites, and ozone reduces how much chemical dosing the operations team manages day to day. Both matter more in commercial use than in a private villa, because the operator carries the running cost.
Catalogue specifications describe the published configuration for this model. Included equipment, jet layout and electrical requirements vary with the options selected on your order, so confirm the final specification in writing before production starts.

Options that change the outcome on a project

The catalogue lists optional accessories for this range: control systems, UV sterilisation, water pumps, heat pumps, sand filtration, insulation and steps. Which of these you specify depends on how the spa will be used.

  • Heat pump. Worth specifying where the spa is expected to hold a set temperature through a cool season. Price it against your actual tariff rather than assuming it is the cheaper option — on an asset that runs daily, running cost usually outweighs capital cost.
  • UV sterilisation and sand filtration. Relevant for shared or high-turnover use, where water quality has to hold up between guest sessions and the maintenance routine has to be simple enough to follow reliably.
  • Insulation. Frequently left out and frequently regretted. On an outdoor unit in a cooler or exposed location, insulation is what keeps overnight heating demand predictable.
  • Steps and access. Safety expectations differ sharply between a private villa and a hotel where children or guests with limited mobility may use the spa. Agree the entry arrangement with your designer before ordering, not on site.

Comparing within the range before you commit

If 6670 mm is difficult on your site, the same range offers alternatives with different equipment mixes — and the differences are not only dimensional. The Outdoor Swim Spa WS-S06CT is listed at 5880 × 2380 × 1400 mm, roughly 790 mm shorter, with the same published jet count and total power. Where length rather than budget is the constraint, that variant is usually the first one worth pricing.

If you have more terrace space and want a longer hydrotherapy section, Outdoor Swim Spa WS-S08CT is listed at 8000 × 2400 × 1420 mm with a higher jet count and more LED lighting. Where the spa is a headline amenity rather than a space-filler, the larger unit gives you more positions in the jet zone.

One caution from project work: do not assume variants in a range share identical equipment. Published pump quantities, jet counts and LED counts differ between models, so read each specification sheet on its own terms instead of carrying figures across from a sibling model.

Site preparation checklist

Before the unit ships, we ask project teams to close out the following:

  • Structural support. A filled shell of this size is a heavy point load. On a deck, podium or terrace, the structural engineer must confirm the slab and its bearings can carry the loaded weight — not just the empty shell.
  • Drainage and overflow route. Agree where first-time drainage and any overflow discharge to, and how the surrounding area drains after use.
  • Electrical intake and routing. Confirm supply type, circuit capacity and the containment route from the board to the control system, with isolation accessible to operators.
  • Access for delivery and lifting. Measure the delivery path — gate widths, level changes, overhead clearance — and decide early whether a crane or gantry is required.
  • Maintenance access. Leave working space at the pump and filter locations so the operations team can service the unit without dismantling finishes around it.
  • Surrounding finishes. Decking, coping and lighting should be set out against the delivered shell dimensions, which is one reason we prefer to coordinate these items in the same package as the spa.

Why buyers source the spa inside a wider package

A swim spa rarely arrives as an isolated purchase. The deck, screening, outdoor furniture, lighting and — on a hotel or villa project — the adjacent bathrooms and fitted joinery all sit on the same works programme. Sourcing them through one hotel furniture and interior fit-out supplier reduces the number of interfaces your site team manages, keeps finishes consistent between indoor and outdoor areas, and lets you consolidate freight and container loading instead of waiting on separate deliveries from several factories.

SANTERSON has operated since 2008 as a China-based manufacturer and one-stop supplier of furniture and building materials for hospitality, villa and office projects. Alongside the swim spa range we supply outdoor furniture for villas and resorts, poolside dining sets and loungers, pergolas and decorative screens, bathroom fixtures, lighting and custom cabinetry. Our stated service scope covers design consultation and space planning, material selection and product specification, manufacturing and quality control, project management with site coordination, logistics and door-to-door delivery, then installation and after-sales support.

For a swim spa specifically, that means the same team can confirm the shell dimensions your decking is set out to, coordinate the electrical requirement with your consultant, and supply the loungers, parasols and planters around it in matching materials. That junction between water edge and furniture layout is usually where a poolside scheme either holds together or falls apart.

Questions to send with your enquiry

To get an accurate quotation rather than a ballpark, include:

  • The available outdoor area and the delivery path from the street to that position.
  • Your supply type and the circuit capacity you can allocate.
  • Whether the spa is for guest use at a hotel or private use at a villa, and expected daily usage.
  • Climate, and whether the spa is expected to hold temperature year-round.
  • Which catalogue options you want priced — heat pump, UV sterilisation, sand filtration, insulation, steps.
  • Any surrounding finishes or furniture to be quoted in the same package.

Send those details and we will confirm the configuration, dimensions and equipment list for your site before production is scheduled.

Review the full Swimming Pools and Swim Spas range, or contact our project team to specify a swim spa against your drawings.