A swim spa is one of the few products on a villa or resort schedule that keeps running after handover. The shell, jets and controls are specified in the contract; what usually causes friction later is the part nobody wrote down — who replaces a failed pump, how a control board is diagnosed from another country, and which consumables you are expected to keep on site. Before you sign an order for a configurable unit such as the Outdoor Swim Spa WS-PC06ST, put the after-sales questions in writing and get answers that name parts, people and lead times.

Confirm the specification you are buying before handover

The WS-PC06ST is a configurable unit within an outdoor swim and hydrotherapy range, so every after-sales term has to attach to one fixed configuration. After-sales conversations go wrong when two parties hold different versions of the same product. The catalogue record for the WS-PC06ST shows overall dimensions of 5900 × 2400 × 1470 mm, one control system, one swim training system, one filter pump, six jets in total and four LED lights, with a listed total power of 6.55 kW. The water pump is not itemised for this model in the captured specification, which is exactly the kind of gap that should be closed on the purchase order rather than discovered at commissioning.

Ask for a signed configuration sheet that lists every item included and every item excluded: control system, swim training unit, filter pump, jets, LED lights, ozone generation, and any optional accessories such as UV sterilisation, water pumps, heat pumps, sand filtration, insulation or steps. A longer variant, the Outdoor Swim Spa WS-PC06ST-L, differs from it in overall length while repeating the same equipment lines in the catalogue, so treat its parts list as a separate document rather than assuming interchangeability. Quote model numbers, not the range name, in every after-sales email.

Ask what the warranty covers, and where it applies

SANTERSON's Furniture Installation and After-sales Support service covers on-site installation, inspection and snag lists, warranty coverage, spare parts and replacement, and ongoing maintenance. Treat those service headings as the starting point of a negotiation, not the final terms. For each element, ask three questions:

  • What is covered by component. Shell and acrylic, jets and plumbing, pump and filter pump, control system and sensors, LED lighting, swim training unit and ozone generator are usually warranted on different clocks. Get the duration for each line separately.
  • What is excluded. Water chemistry damage, limescale, freeze damage from an unheated or uncommissioned spa, unauthorised repair and incorrect electrical supply are common exclusions. Ask for the list in writing.
  • Who performs the work on site. Confirm whether the supplier sends its own installers, works through a local contractor you appoint, or issues remote instructions to your maintenance team — and who pays for that visit.

If your project sits outside China, ask explicitly how warranty service is delivered locally. Warranty wording that assumes an in-country service team is worth little if no such team exists for your region. Confirm the responsible contact, the language of support, and whether labour is included or only parts.

Spare parts: names, numbers and stock on site

Downtime on a swim spa is measured in weeks when a part has to be sourced from another continent. Ask for an exploded parts list with manufacturer part numbers for the wear items and the likely failure items — jet bodies and directional fittings, filter pump and its seals, LED light housings and their gaskets, control board and display, ozone generator, heater element where fitted, plus cover and access hardware.

Then agree a stocking position in the contract: which of those parts ship with the spa, which are held by the supplier for a stated number of years, and what the freight route and typical lead time is for an emergency replacement. For a project with several units — for example a resort installing multiple spas across villas — a small consignment of consumables and common spares in the site store costs far less than an air-freighted single part.

Commissioning, handover and the snag list

Early problems often come from how the unit was installed and supplied with power, not from how it was built. Ask what commissioning includes: electrical supply verification against the total power figure on your configuration sheet, grounding and protection device requirements, levelling and load support for a fully filled shell, start-up of the filtration cycle, jet and swim training performance check, and a water-chemistry briefing for whoever will actually maintain the spa.

Request a handover pack in one document set: as-built configuration sheet, wiring and electrical requirements, control system operating instructions, maintenance schedule, filter and ozone service intervals, warranty certificate with your project reference, and the parts list. A snag list signed at handover, with target close-out dates, is what makes later claims enforceable.

Maintenance support after the warranty period

Ask how you get help in year three. Useful answers are concrete: a named technical contact, remote diagnostics on the control system, replacement modules that plug into the same wiring harness rather than requiring a full control upgrade, and consumables such as filters and sanitisation components available to reorder at any time. Also ask what happens if a component is discontinued — whether a like-for-like substitute is offered and who bears the cost of adapting it.

Maintenance questions are easier to resolve when the spa was bought inside a coordinated fit-out. SANTERSON supplies swim spas alongside Swimming Pools and Swim Spas, together with outdoor furniture, sanitary fixtures and other interior fixtures for villa and hospitality projects. so one supplier contact can handle both the equipment and the surrounding terrace fit-out instead of leaving you to arbitrate between vendors.

A short checklist to send with your enquiry

  1. Signed configuration sheet for model WS-PC06ST, including which pumps and options are included or excluded.
  2. Warranty duration per component, plus written exclusions.
  3. Who installs, who commissions, and what the snag process is at handover.
  4. Exploded parts list with part numbers, stock commitment and emergency freight lead time.
  5. Named after-sales contact, support language, and remote diagnostics scope.
  6. Consumables reorder route and discontinued-part policy.

Buyers who get these six answers in writing before production rarely have an after-sales argument afterwards. If you are specifying a swim spa for a villa or hospitality project, send your configuration requirements to SANTERSON and ask that the after-sales terms come back attached to the quotation, not promised later.