A frosted glass wardrobe front softens a bedroom, hides clutter and keeps a built-in joinery run reading cleanly for years. It is also the part of the job most likely to be argued about afterwards, because glass, hardware and alignment all live under different line items in a quotation. Before you place an order on Frosted Glass Wardrobes or the aluminium-framed version, write down what happens after handover: who answers, what is covered, which parts can actually be replaced, and how a defect gets proved. The questions below are the ones that change the contract language, not just the sales conversation.
1. What exactly is under warranty, and for how long
Wardrobe after-sales coverage is usually split into three pieces with different lifespans: the panel substrate and structure, the surface finish (frosted glass, lacquer, laminate, veneer or acrylic), and the moving hardware — sliding tracks, hinges, handles, soft-close dampers, integrated lighting. Glass fronts fail differently from carcasses. A coating defect, a delaminated film interlayer or an edge chip shows up in the first months; track wear and door sag show up after years of use.
Ask the supplier to state, in writing, the warranty period for each of those three groups, and what voids them. Site conditions matter: moisture from an adjoining bathroom wall, an unlevel floor under a sliding track, or a third-party fitter who trims a door to fit a skirting board can all be excluded. If your project is a villa or apartment handover where the buyer will claim defects later, get the exclusions before you sign, not after.
2. Which spare parts exist, and for how long can they be re-ordered
A made-to-measure wardrobe is a custom item, so the practical question is not whether spare parts exist but which ones are repeatable. Sliding doors on Glass Sliding Door Wardrobes depend on track profiles, hangers, buffers and guides that a local hardware shop cannot match. Ask for:
- a spare-part list naming every fitting in the specification, with supplier part codes;
- confirmation of how long those fittings stay in production or stocked;
- how many replacement glass fronts can be re-made to the same colour and frost level later, and against which reference (a sample, a film code, or a drawing);
- whether spare panels are shipped loose in a future container or must travel as their own consignment.
For multi-unit work — several apartments, guest rooms or a villa with repeat joinery — ask the supplier to keep one reference set of the selected finish and hardware on file. That single step is what makes a repair in year three a straightforward replacement instead of a visible mismatch.
3. Who fits it, and who owns fitting defects
Most wardrobe complaints are installation faults dressed up as product faults: a door that rubs because the track was set out of level, a mirrored panel cracked by an over-tightened fixing, a soft-close damper defeated by an obstructed reveal. Decide before order placement who performs the on-site installation and what they are responsible for. Installation & After-sales Support covers on-site fitting, inspection with a snag list, warranty work, spare-part replacement and ongoing maintenance — but the scope should be confirmed project by project, including who supplies the fitter in your country, whether an engineer or supervisor attends, and what happens if your own builder does the fitting.
Then fix the handover record: photographs of the completed run, a signed snag list with target dates, and a note of any adjustment already needed on day one. That record is what you will point to if a door drifts out of alignment six months later.
4. How a fault gets reported from overseas, and how fast it moves
For imported joinery, response speed is mostly about evidence. Ask the supplier exactly what they need to open a claim — usually the order or project number, the affected position on the drawing, photographs of the defect in place, and a short description of when it appeared. Then ask what happens next: acknowledgement time, whether a replacement part ships immediately or after inspection, who pays freight on a confirmed defect part, and how a replacement glass front is packed for export.
Marketing pages quote response and resolution targets; treat those as starting points to be confirmed in your contract. A useful addition is an escalation route — one named contact, one email thread, and a stated fallback if that contact does not reply within the agreed window. If your site team cannot speak to the factory directly, ask whether someone on the project handles the follow-up in your time zone.
5. Care, cleaning and consumables: what you were told at handover
Frosted glass is unforgiving of the wrong cleaner. Ask for written care instructions covering which cleaners are safe, which abrasives and ammonia-heavy products to avoid, how to clean the frost surface without lifting a film edge, and how often sliding tracks need to be cleared of dust and fibres. Get the recommended lubricant or adjustment method for the hardware rather than a general instruction.
This matters more on rental, serviced-apartment and hospitality work, where housekeeping staff clean daily. A one-page care sheet issued with the handover pack protects the finish and keeps avoidable damage from becoming a warranty argument.
6. Documentation to keep before anything is installed
After-sales claims stand or fall on paperwork assembled at the start. For Frosted Glass Aluminum Frame Wardrobes and any made-to-measure joinery, keep a single file containing:
| Document | Why it matters later |
|---|---|
| Approved shop drawings with revision numbers | Proves which dimensions, door split and handle positions were ordered. |
| Finish and glass reference (sample code, film reference) | Lets a replacement front or panel be matched instead of approximated. |
| Hardware schedule with part codes | Makes tracks, hinges and dampers orderable without guesswork. |
| Packing list and container reference | Ties a damaged or missing component to a specific shipment. |
| Warranty terms and exclusions in writing | Removes the argument about who caused the defect. |
| Signed snag list and handover photographs | Establishes the condition at completion. |
Ask for these items as part of delivery, not as a favour afterwards. A supplier who can produce them on request is a supplier whose after-sales process you can rely on.
7. How to test a supplier's after-sales seriousness before you order
Three short checks during the quotation stage tell you most of what you need:
- Ask for the spare-part list first. A supplier who cannot name their own fittings is unlikely to supply them in year three.
- Ask how a defect claim was handled on a recent overseas project. Specifics — what failed, how the part travelled, how long it took — are worth more than a general assurance.
- Ask what is excluded. Vague answers here translate directly into paid repairs later.
Pair that with an early discussion of whether your wardrobe can be re-made to the same specification if one panel is damaged after handover. Made-to-measure work only stays repairable when the original specification, finish reference and hardware codes are held on record.
SANTERSON works as a furniture and building materials supplier covering design, custom/OEM production, door-to-door logistics, installation and after-sales support, with wardrobe ranges specified to each project's dimensions and finish. If you are comparing quotations for bedroom joinery, send the supplier your drawings and ask them to price the after-sales items above as line entries. That is the fastest way to see which quotation is real.