A two-tone kitchen is rarely the item that holds up a site programme — but an L-shaped run with integrated appliances, a glass display cabinet and a stone backsplash will stall the moment it arrives on site without a proper installation plan. If you are specifying Black & Light Grey L-Shaped Kitchen Cabinets | Custom Cabinetry with LED Glass Display for a villa, apartment or boutique hotel unit, the drawing set you send your supplier and the installation plan you get back should answer the same questions before production starts. Here is what to put in that plan.

Start with the L run itself: dimensions, corner geometry and the working triangle

The product page describes an L layout that forms a working triangle across washing, preparing and cooking. That logic only survives if the two legs are measured on site rather than taken off a design drawing. Send your supplier the finished-floor level, the run length of each leg, and the exact corner condition — square internal corner, angled corner unit, or a run that stops short because a doorway or column interrupts it.

Then confirm what sits at the corner. A lazy-susan, a pull-out carousel or plain shelving all occupy the same footprint but need different carcass widths and different door swings. Note the height of the finished floor to ceiling as well, since the tall cabinet on the right-hand leg is normally built to the soffit.

Fix the appliance schedule before the carcasses are drawn

This layout reserves a central position for a single built-in oven and a tall cabinet that can carry stacked multi ovens. Appliance models decide the ventilation gaps, the electrical positions, the load path into the carcass and whether the tall housing needs a filler or a scribe panel to close to the wall.

  • Name the appliance make and model, or state clearly that equivalents of the same cut-out size will be used.
  • Give the cut-out dimensions and required clearance for each oven, and say whether they are stacked vertically or split across the run.
  • Confirm who supplies the appliances — you on site, or bundled with the cabinetry.
  • Record the electrical load and the position of each outlet so the electrician works from the same drawing as the cabinet fabricator.

If appliances are not selected yet, ask for the carcass to be built to a stated cut-out range and put that range in writing. A tall housing built to the wrong oven stack cannot be corrected with a trim on site.

Specify the glass display cabinet and its lighting properly

The left-hand glass display cabinet with built-in warm LED lighting is the visual centrepiece of this design, and it is also where most installation plans get thin. The plan should state the glazing type and glass thickness, whether the doors are hinged or sliding, shelf spacing for the glassware and tableware you intend to display, and how the cabinet is fixed given that a glazed unit carries less inherent rigidity than a solid one.

For the lighting, specify the colour temperature (the described scheme is warm LED), where the transformer sits and how it stays accessible for replacement, whether the driver is switched from a local plate or a shared circuit, and what happens when an LED strip fails — replaceable strip, or a full shelf-out.

Set out services, sockets and extraction against the elevations

Send marked-up elevations showing every socket, switch, water outlet, waste and extract duct. A two-tone flat-panel run looks unforgiving when a socket sits visibly inside the glass display instead of behind the hob wall. Where the plan calls for an integrated hob, state the hob size and the extractor route early: ducting that has to cross above the tall cabinet changes the ceiling set-out.

Record finishes, substrates and the backsplash build-up

The described scheme pairs contrasting black and light grey flat panels with a marble stone backsplash. Because panel colour and surface finish are fully customisable, your plan should name the exact finish for each run rather than describing it in words — which units are black, which are light grey, and whether handles are integrated or absent. Ask for a physical finish sample to be approved before production; a matte light grey and a high-gloss light grey read completely differently under warm display lighting.

For the backsplash, record the material, slab or tile size, joint positions, edge detail at the worktop and at any glass panel, and the total build-up thickness so the cabinetry can be scribed to it. The product page describes the stone backsplash as waterproof, oil-proof and easy to clean; if your project has a specific cleaning regime, confirm the sealing requirement with the supplier rather than assuming it.

Plan storage internals room by room, not generically

Internal partitions are customised on this product, so list what each zone has to hold. Deep pans next to the oven; a tray or tall unit for bottles near the display cabinet; dry goods away from the heat load. For apartment and boutique hotel work where Custom Built-in Kitchen Cabinets - Interior Fixtures for Hotel & Apartment Projects are repeated across units, keep one internal layout per unit type so the joinery detail does not drift from floor to floor.

Cover delivery sequence, site readiness and the fixing method

The installation half of the plan is where custom cabinetry either goes smoothly or stalls. Include:

  • Package list and crate marking by elevation, so the crew can find the tall housing without unloading everything.
  • Site prerequisites: plaster cured, screed at finished level, first-fix services tested, and a clear access route from the loading point to the kitchen.
  • The fixing method for each wall condition — solid wall, stud partition, or glazing — plus any reinforcement or nogginging the builder must install before closing up.
  • Tolerance allowance at the ceiling and at the L corner, and who supplies the scribe panels.
  • Protection and sequencing: whether worktops are templated after the carcasses are levelled, and when appliances are handed over to the installer.
  • A snag list signed off at handover, covering door alignment across the two-tone fronts, glass panel seating, and lighting function.

For cross-border orders, add who handles freight, customs documentation and container loading. A cabinetry package that lands before the plaster is dry has nowhere to go, so tie the delivery window to the site programme rather than to the production date.

Before you send the enquiry: measured elevations, appliance schedule with cut-out sizes, services drawing, finish approvals signed on physical samples, glazing and lighting detail for the display cabinet, backsplash build-up, and a named site-readiness date. A plan carrying those seven items can be quoted and produced without a second round of questions.

Related configurations worth comparing

Grey Modern Kitchen Cabinets with LED Glass Wine Cabinet | Custom Flat Panel Cabinetry Useful reference when a client wants the same flat-panel language in a lighter palette with a dedicated lit wine display.
Two Tone Wood & White Modern Kitchen Cabinets | Custom Cabinetry with LED Glass Cabinets A two-tone alternative pairing wood grain with white, for projects where an all-grey scheme feels too cold.
Our Services Design consultation, production coordination, logistics and installation support around a fitted kitchen package.

Send the plan as one coordinated pack rather than a drawing with a price request attached. The supplier quotes what you can prove on site, and the same document becomes the checklist the installation crew works from on the day.