A bookshelf that looks right on a render can still fail on site: shelf heights that do not match the books, a unit that cannot be carried through the stairwell, or a finish that does not tie in with the joinery already specified. The checklist below follows the way Santerson Modular Bookshelf Systems are actually configured and delivered — made-to-measure sizing, material and finish options, and project-tailored layouts for residential living spaces — so that every decision is locked down before an order is placed rather than corrected after it arrives.
1. Confirm the scope: modular system or a single loose unit
Start by deciding what you are buying, because the two paths need different information. A loose bookcase is ordered as one object with fixed dimensions. A modular shelving system is ordered as a set of components — uprights, shelf boards, brackets, back panels and infill cabinets — that you reconfigure across a wall or across several rooms. Modular systems are usually specified for whole-floor fit-outs: study walls, living-room media and library walls, hallway runs and home-office zoning.
- The wall or walls involved, measured in millimetres, including skirting, cornices, architraves and any protruding switchboards.
- Whether the run is straight, returns around a corner, or wraps a chimney breast or column.
- How much of the run must stay open for display and how much needs closed storage below.
2. Lock down the dimensions that decide the layout
Modular bookshelves are made to measure, so the drawing you send is the order. Give each dimension a purpose instead of sending one overall size.
| Dimension | Why it matters |
|---|---|
| Overall width and height of the run | Sets the number of bays and whether the unit can be built in one piece or must be delivered in sections. |
| Floor-to-ceiling clearance at the highest point | Ceiling heights often vary along a wall. A floor-to-ceiling system needs the low point recorded, plus the scribe or filler allowance used to close the gap. |
| Depth of shelf boards and of the carcass | Paperbacks, art books, storage boxes and displayed objects need different depths. Depth also controls whether the unit projects into a circulation route. |
| Vertical spacing between shelf positions | Fixed shelves should follow the tallest item in each zone; adjustable shelving uses a row of pin holes or a track so bays can be re-set later. |
| Position of sockets, switches, radiators and downlights | Cable routes and heat sources must be shown on the drawing before panels are cut. |
| Door, lift and stairwell clearances on site | Determines maximum component size that can be brought in and assembled in place. |
Send the measurements as a marked-up sketch or a set of site photos with a tape visible. Where the room is still being built, confirm the finished floor level and the finished wall face — modular units are set out against those two lines.
3. Specify materials and finishes against the rest of the joinery
Material and finish options are part of the configuration, and this is where a bookshelf either reads as built-in joinery or as imported furniture standing in front of a wall.
- Board material. Confirm what substrate is being quoted for shelf boards, carcass panels and back panels, and which surfaces are visible on both faces.
- Surface finish. Match the wood grain, paint colour or laminate already used in the kitchen cabinets, wardrobes and doors. Ask for a physical sample rather than relying on a screen image.
- Edge treatment. Visible front edges need matching edge banding or a solid lipping; exposed square edges are the quickest way to make a made-to-measure unit look stock.
- Metal components. If the design uses metal uprights or frames, fix the profile and colour of the metal frame modular system at the same time as the timber finishes.
- Floating elements. Where part of the design is a wall-mounted display shelf, confirm the fixing detail for the floating modular shelves and the load they are intended to carry before anything is drilled into the wall.
4. Fix the internal layout bay by bay
Modular means the inside is chosen as deliberately as the outside. Walk each bay with the end user and record what it will hold.
- Open display bays for books and objects, with adjustable shelf pitches.
- Closed lower cabinets for clutter, documents and anything out of children's reach.
- Drawers or shelf-focused storage for small items that would otherwise sit loose on an open board.
- Glass-front bays where dust is a concern, with the glass type and hinge direction stated.
- A desk or work surface integrated into the run, if the study wall doubles as a workspace.
Record the layout as a simple elevation drawing with each bay numbered. Numbered bays are also what you check against on delivery.
5. Decide on integrated lighting early
Lighting changes the panel specification, so it cannot be added after the boards are cut. If shelf or bay lighting is wanted, confirm the integrated lighting system at the drawing stage: where the driver sits, how cables are concealed inside the carcass, which bays are lit, and what switching or dimming arrangement the electrician must provide on site. Agree in writing who supplies the lamps, the transformer and the low-voltage wiring, and who is responsible for connecting them.
6. Confirm engineering, loading and wall conditions
- Total intended load per bay — a full bay of books is far heavier than a display of ornaments, and shelf spans must be sized for it.
- Whether the wall can take the fixings, and whether noggins or a battened substrate are needed in plasterboard or masonry.
- Anti-tip restraint requirements, especially in homes with children and in leased or managed properties.
- Level and plumb of the existing wall; out-of-plumb walls are handled with scribes and fillers, not force.
These are site conditions your builder or installer controls. Put them in writing in the order so the panel sizes and fixing method match what will actually be there.
7. Agree the making, delivery and installation route
For an overseas supplier this is the section that most often gets skipped. SANTERSON handles custom furniture production alongside custom and OEM service, logistics and door-to-door delivery and installation and after-sales support, so the same counterparty carries the order from drawing to handover. Confirm each stage before production starts:
- A signed shop drawing and finish schedule, with the revision date on it.
- Packaging, component labelling matched to the numbered bays, and container or parcel loading plan.
- Incoterms, who handles customs clearance and duties, and how the shipment is tracked.
- Delivery address access: lift size, parking, floor, and whether an assembly team is required on site.
- Snag inspection at handover, and what spare parts or replacement panels are available afterwards.
8. Check commercial terms and what is quoted out
- Is the price per linear metre, per bay or per complete wall run — and which components are excluded?
- Are scribes, fillers, plinths, lighting, glass, hardware and installation included or listed separately?
- Payment stages tied to drawing approval, production completion and shipment.
- How a change request after drawing approval is priced and how it affects the schedule.
A quotation that itemises components is easier to compare between suppliers and far easier to police at delivery than a single lump-sum line for "one bookshelf wall".
9. On-site acceptance: the last five checks
- Numbered components match the approved elevation drawing, bay by bay.
- The unit is level, plumb and restrained to the wall as specified.
- Shelf pitches sit where the drawing says, and adjustable pins are fitted with spare holes capped.
- Finish continuity at the junctions with floor, ceiling and adjacent joinery — scribes cut tight, edges unchipped.
- Lighting, if specified, works on every lit bay, with access to the driver left reachable.
A short checklist to send with your enquiry
- Measured elevations of each wall run, in millimetres, showing sockets and obstructions.
- Intended contents per bay, so shelf depth and pitch are engineered properly.
- Finish references matched to existing joinery, with samples requested.
- Lighting decision, fixed or adjustable shelving, open versus closed bays.
- Site access constraints and delivery address details.
- Written confirmation of what is included in the price, plus lead time and after-sales terms for your destination.
Send those six items together and a made-to-measure quotation comes back comparable rather than approximate. If you want one party to draw, manufacture, ship and install the run as part of a wider fit-out, our team can take the project from interior design services through production and handover — contact us with your drawings for a specification and quotation.
SANTERSON — furniture and building materials manufacturer, one-stop project supplier since 2008.
Contact: PHILLIP | Phone / WhatsApp: +86-13928214007 | Email: santerson@qq.com
Send your drawings and measurements for a modular bookshelf quotation.