A wardrobe that looks right in the showroom drawing can still cause trouble on site if the paperwork behind it is thin. Decorative moulded paneled doors are one of the most specification-sensitive items in a bedroom fit-out: the profile of the moulding, the direction of the grain, the substrate under the finish and the way the door meets its frame all change how the finished piece reads once installed. For procurement teams managing villa, apartment or hospitality bedroom packages, the difference between a smooth handover and a costly rework usually comes down to what was written down before production started.

This guide sets out the documentation a procurement team should hold on file for decorative moulded paneled wardrobes, room by room and line by line, so approvals are traceable and variations do not turn into disputes.

Why Panelled Wardrobes Deserve Their Own Specification Sheet

Moulded paneled doors are assembled from components rather than cut from a single sheet. A typical door carries a frame member, a moulded edge profile and a centre panel, and each of those can be sourced, finished or tolled slightly differently. Small deviations are visible: a moulding radius that is deeper than approved catches more shadow, a panel set proud instead of recessed changes the sight line, and a finish colour matched under different lighting reads warm in one room and flat in another.

Because of this, a single generic line on a bill of quantities — "built-in wardrobe, classic style" — is not enough to hold a supplier or contractor to a defined outcome. A dedicated specification sheet, referenced by number on the drawings and repeated on every purchase order, gives everyone the same benchmark at inspection.

The Documentation Set to Assemble Before Order

Treat the following as the working record for each wardrobe type in a project. Where a value is still open, it should be shown as an option with a decision date, not left blank.

1. Dimensional and setting-out records

  • Room elevation drawings for every wardrobe location, showing overall height, width and depth, plus the position of skirting, architraves, cornices and any ceiling rebate the carcass has to accommodate.
  • Confirmation of which dimensions are fixed by the building (floor-to-ceiling height, structural returns) and which are design choices, so tolerances land where they can be absorbed.
  • Made-to-measure confirmation for each unit rather than a single nominal size applied across a whole floor. Where units repeat across levels, record the variation at each location.
  • Clearance notes for doors and drawers: swing radius, handle projection, and the space needed for adjacent furniture or a bed door to open without fouling the fronts.

2. Door style and moulding profile

  • A named reference to the panel type being ordered, with the supplier's own catalogue name or code recorded on the specification so the same profile is quoted again on variations.
  • A drawn or photographed detail of the moulding: frame width, profile depth, and whether the centre panel sits raised or recessed within the frame. Related styles such as raised panel wardrobes and recessed panel wardrobes differ mainly in this detail, so record which one is approved.
  • Panel count and layout per door — a single tall panel reads differently from a two-panel or arched-top composition, and the number of rails affects both appearance and cost.
  • Approval of a physical sample door, signed and dated, held on site as the reference for inspection.

3. Substrate, finish and colour authority

  • The substrate behind the moulding for each component — frame member, panel and any applied moulding — since a single door can combine more than one board type, and the visible result depends on all of them being finished consistently.
  • Finish system and sheen level (matte, satin or gloss), stated separately for carcass interiors and door fronts, which are frequently specified differently.
  • Colour authority: the manufacturer's own swatch reference rather than a generic colour name, plus a note of whether doors from different production batches were approved against the same physical sample.
  • Edge and profile treatment. Moulded profiles are where finish quality is most exposed, so record whether the profile is painted, laminated or veneered after assembly, and inspect the corners on the sample.

4. Interior layout and hardware schedule

  • A shelf, hanging-rail and drawer schedule per unit, showing quantities, widths and positions — this is the part most often changed late, so version control matters.
  • Hardware make and model for hinges, slides, handles and any soft-close mechanism, with load ratings recorded for drawers intended for heavy items.
  • Door configuration: hinged, sliding or open-front. If the project mixes configurations across room types, list them per location rather than assuming one default.
  • Any integrated lighting, mirror panels or glass inserts recorded as separate line items with their own approvals, since they involve different trades and lead times.

5. Interface and coordination notes

  • Which trade sets out the floor leveling, wall preparation and skirting removal, and at what point — a made-to-measure wardrobe measured before those works are complete inherits their irregularities.
  • Sequencing against flooring, painting, electrical first-fix and lighting: whether the unit sits on finished floor or on a prepared screed, and where the architrave meets the carcass.
  • Fire, egress and accessibility requirements applicable in the project jurisdiction, with responsibility for confirming them named in the contract. Where joinery sits near a protected route or a required clear opening, record that constraint explicitly.

A Practical Documentation Checklist

DocumentOwnerNeeded before
Room elevations with fixed and variable dimensionsDesign / architectural teamSupplier quotation
Approved sample door with signed finish referenceProcurement + design leadProduction release
Moulding profile detail (frame width, panel treatment)Supplier / manufacturerProduction release
Interior layout and hardware schedule per unitDesign teamOrder placement
Site re-measure record against final floor and wall levelsSite contractor + supplierFinal manufacture
Delivery, storage and installation method statementSupplier / installerSite delivery
Snag list and sign-off sheet per unitSite clerk of worksHandover

Where Custom Manufacturing Changes the Paperwork

When a project specifies made-to-measure wardrobes rather than catalogue sizes, more of the record sits with the manufacturer. A supplier offering custom and OEM service should return shop drawings for approval before production, showing the approved profile, the finish reference and the interior layout as built rather than as drawn at concept stage. Ask for those drawings to carry a revision number and date, and keep them with the purchase order — they become the comparison document at inspection.

For multi-unit projects, ask how colour and profile consistency is managed across production runs, and whether a retained approved sample will be held for the duration of the programme. If any part of the package spans more than one supplier — doors from one, carcasses from another, hardware from a third — record the interface responsibility explicitly so that a mismatch at the hinge hole or the reveal cannot be passed between parties.

Two records save more time at handover than any other: the signed sample door held on site, and the final re-measure sheet confirming that what was manufactured matches what the finished room can actually receive. Both are cheap to produce and expensive to do without.

Coordinating Wardrobes Within a Wider Fit-Out Package

Wardrobe documentation rarely stands alone. In villa and apartment packages the same finishes recur across kitchens, vanities and wall panelling, and a finish approved for one item is often assumed to match another. Where a project deliberately matches or contrasts a wardrobe finish with kitchen fronts or interior fixtures, record that relationship in the schedule so a substitution on one line does not silently break the scheme elsewhere.

Working with a supplier that handles turnkey project delivery — design coordination, production, logistics and installation under one scope — reduces the number of interfaces to document, but it does not remove the need for approvals. The same sample sign-offs, shop drawings and re-measure records still apply; they simply move between fewer parties.

Closing the Record at Handover

Close each wardrobe type with a unit-by-unit snag sheet covering door alignment, gap consistency along the moulded profile, finish condition on edges and profiles, and drawer and hinge operation under load. Attach photographs of a representative completed unit, cross-referenced to the approved sample number. That single file — specification, drawings, samples, re-measures, snags — is what supports warranty conversations months later and what makes a repeat order for another phase far quicker to place.

If your project needs made-to-measure paneled wardrobes specified and documented to that standard, contact SANTERSON with your drawings and the profile you are working from, and we will return shop drawings and finish references for approval before production.