Vanity lighting sits in an awkward place on most project schedules. It is small enough to be treated as an accessory, yet it governs how guests shave, apply make-up and judge the quality of the whole bathroom fit-out. When a lighting line item arrives at a supplier late in the procurement cycle, the usual results are substitutions that do not match the mirror, electrical points that no longer align, and change orders nobody budgeted for. A well-written procurement brief prevents all three. Here is what a purchasing team should lock down before requesting quotations.

Start With the Mirror and Vanity, Not the Fixture

Vanity lighting is defined by what it lights. Before naming a fixture, the brief should state the vanity type and mirror selection, because each combination changes the mounting geometry. A floating vanity leaves wall space clear for sconces placed at face height, while a floor-standing single or double vanity often pushes the lighting above the mirror line. Integrated options go further: an LED mirror cabinet carries its own light source, which removes the separate fixture from the schedule but adds electrical and driver-access requirements at the cabinet position.

State in the brief which of these three approaches applies to each bathroom type in the project — surface-mounted sconce or bar fitting, integrated mirror lighting, or a decorative accent light. Mixing approaches across room types is normal; leaving them undecided until order placement is not.

Put the Electrical Coordination in Writing

Most vanity lighting disputes are electrical, not aesthetic. The brief should require the supplier to confirm, for every fixture type:

  • the mounting height and lateral centring relative to the mirror and basin, given on a dimensioned drawing;
  • the back-out position of the supply point, and whether the fitting is hard-wired or plug-connected;
  • switch location — wall plate, vanity-integrated, or sensor — and whether it controls the light alone or shares a circuit with a demister pad or mirror cabinet lighting;
  • dimming method and compatibility with the dimmer boards already scheduled by the electrical contractor.

A supplier who works from drawings rather than catalogue images will flag clashes between the sconce, the mirror cabinet door swing and the shower screen before production starts. Ask for that coordination as a deliverable in the quotation, not as an afterthought during installation.

Specify Performance Without Over-Specifying

For project briefs, performance language should be practical and verifiable. Reasonable items to request are colour rendering suitable for grooming tasks, a consistent colour temperature across all bathrooms of the same type, and even illumination on the face plane rather than glare at eye level. Where the fitting sits close to a basin or shower enclosure, ask the supplier to confirm the suitability of the fitting for that bathroom zone in writing, along with the wiring method they recommend.

Avoid copying numbers from marketing sheets into your brief. If a datasheet quotes lumen output or ingress protection without a test reference, request the confirmed value for the exact configuration you are ordering. Specification errors survive for years inside a handed-over O&M manual.

Decide How Decorative the Light Is Allowed to Be

In hospitality and villa projects, the vanity wall is often the most photographed corner of the bathroom, and clients increasingly expect the light itself to be a design feature. A decorative LED sconce for a bathroom vanity area — for example a sculptural wall fitting with a mirrored centre — can replace both a plain bar light and a piece of wall art, which simplifies the schedule if it is decided early. Where this route is chosen, the brief should still separate the decorative fitting from task lighting duties, so guests are not left grooming by an accent light alone.

Ask for Made-to-Measure Where the Layout Demands It

Standard catalogue sizes rarely fit every bathroom in a project. Double-vanity walls, niches, and mirror cabinets of non-standard width all create situations where a fixed-size fitting looks wrong. Manufacturers working to project drawings can adjust size, finish and layout of vanity lighting to suit each space, the same way they make vanities and mirror cabinets to measure. The brief should say explicitly which bathroom types require made-to-measure lighting, and require prototype or sample approval for those items before batch production.

A Short Checklist for the Brief

ItemWhat the brief must state
Vanity and mirror pairingVanity type (floating, single, double), mirror or mirror-cabinet model, overall widths.
Fixture approach per room typeSurface-mounted, integrated cabinet lighting, or decorative accent — decided per bathroom type.
Electrical coordinationSupply-point positions, hard-wire method, switching, dimming compatibility.
Performance requirementsColour temperature consistency, rendering for grooming, zone suitability confirmed by supplier.
Custom scopeWhich items are made-to-measure; sample approval before batch production.
Packaging and sparesFixture-level packing for site handling; spare units ordered with the batch for future replacement.

Vanity lighting rewards procurement teams who treat it as part of the bathroom package rather than a late accessory. Bundling vanities, mirror cabinets and their lighting with one supplier keeps dimensions, finishes and electrical details on a single set of drawings, which is how the line item stays off the variation list. Send your bathroom schedule and mirror selections early, and ask for coordinated shop drawings before you place the order.