Open shelving paired with minimalist cabinet fronts is one of the easiest ways to make a kitchen or bathroom feel lighter and less boxed in. It is also one of the easiest things to get wrong, because nothing hides: shelf heights, panel edges, dust exposure and what you actually keep on display all become visible decisions once the doors come off. If your drawings show open bays inside a run of open shelving minimalist cabinets, the items worth locking down before production starts are mostly settled in the first round of coordination, not on site.
1. What goes on the open bays, and how often it moves
Start with an inventory rather than a mood board. Glassware, daily dishes, cookbooks, small appliances, cleaning products and decorative pieces all want different shelf depths, clear heights and load capacities. A bay planned for tall bottles behaves very differently from one planned for stacked plates. This is the conversation we try to have at the specification stage on custom minimalist kitchen cabinets projects, because a shelf set to a generic pitch usually ends up either wasting vertical space or refusing to take the item it was meant to hold.
Then be honest about how often those items move. Daily-use pieces need reach without a step stool; seasonal or display-only pieces can sit higher. Where we know the loading will vary, adjustable shelving on standards or in modular open modular shelves keeps the layout editable after handover instead of fixing it for good.
2. Shelf span, thickness and what the panels are carrying
Closed cabinets hide deflection; open shelving shows it. Before production, confirm the clear span of each open bay, the panel thickness being used across that span, and the intended load. Long unsupported spans in a thin board will sag over time under heavy items, and this is one of the few defects that no hardware fix really solves afterwards. Where a bay runs wide, the practical options are shortening the span with a vertical divider, thickening the shelf, or introducing a concealed support — each changes the look, so it needs to be decided with the designer rather than corrected in the factory.
Loading matters just as much in wet and semi-wet areas. Our open shelving listings for bathroom projects state that dimensions, finish and intended loading are confirmed per project, which is exactly how they should be treated: a shelf holding glass bottles in a humid room needs a different board and edge treatment from one holding towels.
3. Edge detail, finish and how the two meet closed fronts
In a minimalist scheme the open bay is where the material quality is judged, because you see the panel edge and not just the face. Confirm which edge treatment is specified — matching solid edge, ABS or PVC edge banding, or a mitred wrap — and check that it matches the finish on the closed fronts in the same run. Two-tone schemes are the usual trap: a carcass in one colour with interior shelf panels in another can look deliberate or accidental depending on whether that contrast was drawn.
Finish selection should follow the room's use. Matte solid panels and subtle wood textures suit handleless, low-visual-noise kitchens; near a hob or sink they also need to be genuinely wipeable. Where the design leans on continuous, unbroken surfaces, that usually means handleless minimalist kitchen cabinets with touch-to-open or integrated profiles next to the open bays — worth confirming early, because the reveal between an open bay and a handleless door has to be dimensioned so doors swing clear without fouling the shelf edges.
4. Structure, fixing and wall conditions
Open shelving carries its load through fewer members than a closed carcass, so the supporting condition needs confirming before anything is cut. For wall-hung and floating configurations, check what is behind the wall — stud positions, timber nogging or steel backing — and whether the substrate can take the intended load plus impact. Floor-to-ceiling and freestanding systems raise a different question: whether the unit is restrained to the wall or floor, and how that restraint is concealed while still allowing for uneven floors and ceilings, which every existing site has.
For taller runs such as floor to ceiling shelving systems, confirm how the unit is built and delivered. A single tall assembled box is harder to bring through a stairwell or lift than a system that arrives in modules and is joined on site; that decision affects both delivery logistics and the joint detail you will see afterwards.
5. Lighting, sockets and services inside the joinery
Lit open bays are where most late changes come from. If shelf or niche lighting is intended, confirm before production which shelves take a cable channel or surface-mounted fitting, where the driver sits and how it stays accessible for replacement, and what switch or sensor arrangement the client expects. Our integrated cabinet lighting listing notes that electrical specification and compatibility must be confirmed against each cabinet design — that confirmation belongs in the drawing stage, not on the installation day.
The same applies to sockets inside open niches for kettles, coffee machines or charging points. Their position has to clear the shelf line, stay reachable, and survive splashes where relevant. Cutting a lit, finished panel on site is visible forever.
6. Dimensions: who measures, and against which drawing
Most avoidable rework on built-in joinery traces back to dimensions taken from the wrong source. Before production, confirm that the manufacturing dimensions come from a site survey of the completed shell — after flooring, tiling, plaster and services are set — rather than from architectural drawings alone. Then confirm the datum: which wall is the reference line, where the run starts and ends, and how corners, scribes and appliance recesses are handled. For made-to-measure work this single confirmation removes most of the arguments later.
Also confirm what the finished dimensions include — worktop thickness, splashback, skirting removal, door swing clearances — since each of these quietly reduces an internal dimension that someone has already drawn a shelf into.
7. Maintenance and what open shelving costs you over time
Open bays need dusting, and shelves near a hob need degreasing far more often than the inside of a cupboard. Confirm with the client that they have accepted this trade before production, because it is the most common reason owners ask to add doors after installation. Practical mitigations are simple: keep high-grease zones behind closed fronts, place open bays away from direct hob spray, choose finishes that tolerate repeated cleaning, and use baskets or trays on display shelves so items can be removed in one motion.
8. Documentation to sign off before the panels are cut
Before releasing a run into production, we ask for the same short set of confirmations on every project:
- Manufacturing dimensions from a site survey of the completed shell, with the datum stated.
- Shelf layout per bay — fixed or adjustable pitch, clear heights against the items listed for that bay.
- Panel material, thickness and edge treatment for every visible open shelf, matched to the closed fronts.
- Load assumptions per open bay, and how spans longer than the board can carry are resolved.
- Wall and floor fixing details, including backing requirements and restraint method for tall units.
- Electrical routing, driver location and access for any lit bays or in-joinery sockets.
- Finish sample sign-off under the room's actual lighting, not only on the factory bench.
- Delivery route and module sizes against lift, stair and doorway dimensions.
How we take these through production
SANTERSON has manufactured furniture and building materials since 2008 for villa, hospitality and office projects, offering custom and OEM service covering bespoke dimensions, panel materials and finishes. For open shelving schemes that means the layout, loading, edge detail and electrical provisions are confirmed against your drawings before panels are cut, and the same production run can carry the matching closed fronts, tall pantry units and adjacent storage walls — which is usually how a minimalist scheme stays visually consistent from one elevation to the next.
If you have drawings ready, send the elevation together with the intended use of each open bay and we will come back with the specific gaps to close before production. Enquiries are handled through our contact page.