A high gloss lacquer wardrobe reads beautifully on a rendering and even better once it is installed under bedroom lighting. The problem is that two wardrobes described with the same three words can look and wear very differently on site. Before you sign off an order, the finish needs to be pinned down in writing: what the substrate carries, how many lacquer stages sit on the door face, which direction the sheen runs, where the edges are dressed, and who signs the approved sample. The notes below follow the way we build High Gloss Lacquer Wardrobes for villa and apartment projects, so you can use them as a checklist in your own specification.

Start With the Substrate, Not the Colour

Gloss magnifies everything underneath it. A flat, stable panel makes a mirror-like surface easy to achieve; a panel that moves with humidity will show as ripples, sink marks at joints, or a visible shadow line along a routed detail. For built-in wardrobes we work from engineered board substrates rather than solid timber for the large door faces, and we ask buyers to confirm two things before the finish is fixed:

  • What the door core and face material are, and which side of the panel receives the lacquer. A single-sided lacquered door behaves differently from a fully lacquered one when it is fixed into a recessed wall niche.
  • Whether the carcass and the doors come from the same batch of board. Mixed batches are the usual reason a colour looks correct on the sample and slightly off across a full run of wardrobes.

Our Lacquer Wardrobes collection is made to measure, so panel sizes, door layout and material choice are set per project. That flexibility is exactly why the substrate has to be written into the order instead of assumed from a previous job.

Confirm the Lacquer Build-Up in Stages, Not Adjectives

"High gloss lacquer" is a finish family, not a recipe. Ask the factory how many priming and finishing coats go on, and whether the surface is sanded and polished between stages. A build-up that is sanded and polished after the final cure gives the depth you see in a good showroom sample; one that simply stops at the last wet coat stays flatter and shows orange peel under downlight.

Detail to confirmWhy it matters on site
Number of primer and top coats, plus whether sanding and polishing sit between themDetermines depth of reflection and how the door reads under LED strips and ceiling spots
Cure method and whether panels are handled before full cureUnder-cured panels pick up handling marks and are vulnerable to packaging impressions in transit
Colour reference: RAL, Pantone or a physical sprayed panelA colour code alone cannot capture the depth of a lacquered surface; a sprayed panel can
Whether metallic, pearl or solid pigment is usedMetallic and pearl pigments shift noticeably with viewing angle and light temperature

For white and light neutrals, ask specifically about the lacquer system used on light colours. Some systems yellow slightly over time on pale shades, and that only becomes visible a year after handover, usually on the doors nearest the window.

Decide Where the Gloss Stops: Edges, Profiles and Reveal Lines

This is the detail buyers most often leave out of the drawing. On a high gloss door the eye travels straight to the edge, so the edge treatment sets the whole character of the run.

  • Wrapped versus flat-lacquered edges. Wrapped edges give a consistent radius and protect the corner; flat-lacquered edges on a mitred profile look seamless but demand careful handling and precise fixing.
  • Handle choice and its shadow line. A handleless door with an integrated profile reads cleaner against gloss, but the reveal depth must be drawn and agreed, otherwise the gap varies across doors. If you prefer hardware, confirm the fixing positions on the elevation before production.
  • Carcass-to-door relationship. Decide the reveal between adjacent doors and between door and carcass, and whether doors are inset or overlay. On a gloss face an uneven reveal is obvious from two metres away.
  • Corner and return panels. Where a wardrobe returns into a wall niche or meets a window architrave, confirm how the scribe or filler panel is finished so it matches the door face rather than the carcass laminate.

Where a full gloss front feels too reflective for a bedroom, we often split the elevation: gloss lacquer on part of the run, with Glass & Lacquer Combination Wardrobes carrying the display bays. The same finish discipline applies, but you also confirm glass type, tint and the frame detail at the meeting stiles.

Agree a Physical Approval Sample Before Production Starts

For any gloss order, request a sprayed sample panel of the actual door construction — substrate, edge treatment and all — not just a colour chip. Then check it in three conditions: daylight, warm artificial light, and cool LED. Gloss shifts more with light temperature than almost any other finish, and a sample approved only under showroom lighting can read quite differently against bedroom walls.

  • Sign and date the sample, photograph it, and attach it to the purchase order as the approval reference.
  • Ask which face of the sample is the front, so the direction of polish and any grain effect is unambiguous.
  • Keep the approved sample through handover; it is your only objective reference if a replacement door is needed later.

Practical note: on made-to-measure work, an approval sample adds time to the front of the programme. Build that step into your schedule rather than waiving it to protect a delivery date.

Interior Finish and Hardware Are Part of the Specification

A gloss front is only half the wardrobe. Interior panels, drawer fronts, shelves and hanging rails are usually specified at the same time, and a mismatch in sheen or edge banding colour is one of the first things a client notices when the doors open.

  • Interior board colour and edge banding: confirm the banding matches the carcass, and note the thickness for visible edges.
  • Drawer fronts and internal fittings: state whether these carry the same lacquer or a matching laminate, since a matching laminate is common inside and cheaper without any visual cost.
  • Hinges, slides and soft-close hardware: name the brand and series in the order, and confirm load ratings for tall doors. Tall gloss doors sag over time if hinges are under-specified, and sagging shows as an uneven reveal.
  • Integrated lighting: if you plan interior or vanity lighting, decide the cable route and transformer position now. Drilling into a cured gloss panel after the fact is not a clean repair.

Because we manufacture rather than resell stock fronts, internal layout — drawer-focused, shelf-focused, hanging modular, or a corner configuration — is drawn around the client's storage plan and confirmed against final site dimensions. If you are coordinating several bedroom types on one project, send the room-by-room elevations with your enquiry so each wardrobe is quoted on the same basis.

Site Conditions and Installation Tolerance

High gloss wardrobes expose poor substrate work in the room itself. Before installation, confirm that floors are level where the unit sits, that walls are plumb enough for the chosen reveal, and that any built-in recess has been finished to a consistent depth. Where the building is still wet — fresh screed or newly plastered niches — allow the space to dry before fitted joinery goes in, and keep panels protected until painting is complete.

  • Confirm who sets out the unit on site: our installer or your tradesperson. This decides who owns the final reveal adjustment.
  • State the tolerance you will accept across the run, door by door, and inspect with the approved sample to hand.
  • Record packaging condition at delivery. Gloss panels are the first items inspected for transit damage, and photos taken at the container do far more than a note on a delivery docket.

Our installation and after-sales support covers on-site fitting, inspection with your snag list, spare parts and replacement panels. Warranty terms, response times and the availability of local installers differ by project and by country, so we set them out in writing for each order instead of quoting a blanket promise. That matters most on Australian villa work, where the fitting sequence has to be agreed alongside the other trades.

How This Fits Into a Larger Fit-Out Order

Wardrobes rarely sit alone. On villa and apartment projects we usually price them together with the custom built-in kitchen cabinets, vanities, doors and wall panelling for the same building, because the lacquer system, hardware range and board sourcing then stay consistent across rooms. One supplier coordinating cabinetry, fixtures and finishes also means a single set of drawings to reconcile and one production schedule to track.

If you are comparing suppliers on gloss wardrobes, put the questions above in writing to each of them. Answers that stay at the level of "high gloss, any colour" usually mean the finish build-up, edge treatment and approval sample have not been considered — and those are exactly the items that decide whether the installed run looks like the rendering.

Frequently Asked Questions

What is the difference between high gloss lacquer and high gloss acrylic on a wardrobe door?

Both give a reflective front, but they are applied differently. Lacquer is sprayed in stages onto the panel and can be sanded and polished between coats, which is why it reads deep on curved or mitred details. Acrylic fronts are sheet materials bonded to the door. Both appear in our catalogue, and the choice usually comes down to the door geometry and how much edge detailing your design relies on: lacquer suits mitred and curved details, while acrylic fronts are sheet materials bonded to the door.

Can I order a matte version in the same colour?

Yes. The Lacquer Wardrobes collection includes a matte lacquer option alongside the high gloss version, which is a practical way to keep one colour across a bedroom while reducing reflection on larger surfaces. Confirm that both finishes are sprayed from the same pigment batch if they appear in the same sightline.

Do you make wardrobes to non-standard ceiling heights?

Yes. The collection is made to measure, with layout and dimensions set per project, including floor-to-ceiling runs into niches and under sloped ceilings. Final site dimensions should be taken after wall and floor finishes are complete, then confirmed against the shop drawings before panels are cut.

What information speeds up a quotation?

Room elevations with dimensions, the number of wardrobe types, your preferred substrate and edge treatment, hardware brand or series, and the colour reference. If you send photographs of the site condition — especially niches, returns and skirting details — we can flag fixing problems at quotation stage rather than after production.

SANTERSON is a China-based furniture and building materials manufacturer supplying custom fitted furniture and interior products for villa, hospitality and office projects. Send your elevations, dimensions and finish reference through our contact page, and we will confirm the lacquer build-up, edge detail and approval sample before anything goes into production.