A swim spa that looks right on a rendering can still stall on site. Access routes, structural slabs and electrical supplies all have to agree with the unit you specified. This article walks through how we coordinate our Outdoor Swim Spa WS-PC02 with design drawings and site requirements, so architects, contractors and procurement teams can lock the details down before production starts rather than after the shell is poured.
Start from the catalog footprint, then check it against the drawing
The WS-PC02 is a square hydrotherapy unit in our swimming pool range. The catalog dimensions we publish are 3000 × 3000 × 1050 mm, which makes it a good fit for terraces, villa courtyards and resort podium decks where a long lap pool would not sit comfortably.
On the drawing, we ask three questions before anything is signed off:
- Clear opening versus finished size. The 3000 × 3000 mm figure is the shell. A tiled surround, coping or a recessed platform all take space, and the unit still has to pass through gates, doors and lifts on its way to position.
- Deck level and water line. The 1050 mm height sets the relationship between finished floor level and the water surface. We mark both on the landscape and exterior finish plans so the coping detail does not have to be invented on site.
- Plant access. Pumps, filtration and the control system sit within reach of an access panel. A plant zone that is drawn but never built is one of the most common causes of a delayed handover.
Read the equipment list as a scope document, not a brochure line
The specification shown for this model lists a control system, two water pumps, one filter pump, sixty jets and an LED light, with total power of 7.35 kW. Those figures describe the catalog configuration. They are the starting point for coordination, not a substitute for the confirmed order.
Optional items in this range include control systems, UV sterilisation, water pumps, heat pumps, sand filtration, insulation and steps. Each one changes something on site:
- A heat pump adds an outdoor plant position that needs ventilation, a drain and clearance for servicing.
- Sand filtration changes the pipework routes and the space needed around the vessel.
- Insulation affects how the shell sits in a recessed platform and how the deck is built up around it.
- Steps change the entry geometry, so they must be drawn with the coping rather than added later.
We send the confirmed configuration back to the design team as a marked-up layout, with each pump, jet group and control item shown in its planned position. That single document usually prevents several separate site queries.
Electrical and structural coordination before the slab
With total power of 7.35 kW for the catalog configuration, the electrical supply needs to be sized by the project engineer for the exact equipment selected, including any options added after the first quotation. We provide the confirmed equipment list so the engineer can work from it; the local supply arrangement, protection device and any required inspections remain with the project's electrical contractor and local authority.
On the structural side, a filled shell is a heavy point load. Whether the unit sits on a ground slab, a transfer slab or a suspended terrace deck, the supporting structure has to be designed for the wet load plus the surrounding finish. We coordinate position and support conditions with the engineer; we do not design the structure for the project.
Drainage is the third item worth resolving early. Overflow, drainage to plant areas and any drip or condensate routes should appear on services drawings before the waterproofing membrane goes down.
Where a customised shell saves time
Not every plot accepts a square footprint. Where the terrace is narrow, curved or bounded by an existing structure, our Customizable Shape Outdoor Spa covers square, round, oval and curved layouts in an acrylic shell with structural reinforcement. Choosing the shape at drawing stage avoids cutting back a completed deck.
For projects that want swimming as well as hydrotherapy, compare the WS-PC02 against the Long Outdoor Swim Spa with Hydrotherapy & Relaxation Pool. A longer shell changes transport, crane access and deck length, so it is worth testing both options against the same site plan before the client commits.
Delivery, installation and handover as one sequence
Because we also supply furniture and building materials for villa and hospitality projects, the spa is coordinated alongside the rest of the package through our project services. Under custom and OEM work, finish and configuration choices are fixed with drawings before manufacture. Logistics and door-to-door delivery covers freight, packaging and container loading plans, which matters for a unit that has to arrive in sequence with the site programme rather than sit on a wharf. Installation and after-sales support covers setting, inspection of snags and the handover record.
Delivery windows, crane availability, site access hours and local inspections are confirmed with the project team for each order. We do not commit to a transit time or an installation date until the programme is agreed.
A short pre-production checklist
- Confirmed model and configuration, including every option in the order.
- Setting-out drawing with finished floor level, water line and coping detail.
- Access route from the delivery point to position, with clear widths and heights.
- Structural sign-off for the wet load at the chosen location.
- Electrical schedule for the confirmed equipment, sized by the project engineer.
- Drainage, overflow and plant access shown on services drawings.
- Named site contact for setting, inspection and handover.
Send us your drawings and site constraints, and we will return a marked-up layout for the WS-PC02 with the confirmed equipment list, so the coordination happens on paper while changes are still cheap. Enquiries go through our contact page.