A swim spa quotation for a hotel, resort or residential tower rarely arrives in a form that lets you compare it against the next one. Two proposals may list the same model code, the same overall length and almost the same price, yet differ by thousands of dollars once site works, electrical supply, filtration duty and freight are settled. This guide walks through how to read a proposal for the Outdoor Swim Spa WS-S06CT-L in a commercial setting, so that the number you approve is the number you end up paying.
Start with the shell footprint, not the model code
The catalogue entry for this unit lists an overall envelope of 6670 x 2380 x 1400 mm. For a project team those three figures matter more than the model designation, because they decide whether the spa fits the terrace, plant room or podium deck you have allocated, and whether it can be lifted into position by crane or must be assembled in place.
Check three dimensions separately on the drawing that comes with the quotation:
- Gross external envelope: including steps, cabinet cladding and any protruding control or equipment housing, which is what has to clear doors, lifts and slab edges.
- Water line height: which governs splash zone, deck drainage and parapet heights around an exposed rooftop installation.
- Access and service envelope: the space left for pump, filter and control access. A proposal that parks the cabinet hard against a boundary wall without an access strip will fail inspection later, no matter how well the spa itself is specified.
Ask the supplier to confirm the dimension set in writing against the drawing revision number. Where the site condition is tight, this is also the moment to ask whether a shorter unit from the same range would serve. The WS-S06CT shares the 2380 mm width and 1400 mm depth with a shorter shell, which can be decisive on a narrow balcony.
Read the equipment schedule line by line
The published specification for this configuration shows one control system, one swim training unit, one water pump, one filter pump, 31 jets in total and four LED lights, with a total power figure of 8.35 kW as listed in the catalogue. Treat that list as the baseline you compare against, not as the finished scope.
In a commercial installation the following items are what separate two quotations of similar headline value:
- Filtration duty versus shell size: a single filter pump sized for domestic cycling may be undersized for guest-driven, high-frequency use. Ask for the turnover rate and run schedule the supplier has assumed for your occupancy profile.
- Heating arrangement: catalogue options for this range include heat pumps, insulation packages and cover options. A quoted 8.35 kW total power figure describes the standard configuration; a heat pump added to hold water temperature overnight changes both the connected load and the running cost.
- Water treatment: ozone appears in the standard feature list, with UV sterilisation offered as an option. Commercial operators should decide disinfection strategy before award, because it affects dosing plant, chemical storage and inspection paperwork.
- Swim training unit specification: nozzle type and flow determine whether the unit is realistic for lap training and physiotherapy use or only for light resistance play. Confirm what is actually fitted at the quoted price.
Where a competitor quotation lists a higher jet count, ask which jets are air, which are water and how many are on the seat circuit versus the swimming circuit. Jet totals are easy to inflate and hard to compare unless the schedule is broken down.
Confirm the electrical and structural interface early
The most expensive surprises on swim spa projects sit outside the supply package. A commercial power distribution, an isolator at the required distance, a dedicated circuit sized for the selected configuration and a compliant RCD arrangement all belong to the main contractor or the building services engineer, not to the spa supplier.
Before you approve the proposal, request from the supplier: the connection diagram, the full-load current per phase for the exact fitted configuration, and the recommended cable sizing. Then hand that to your electrical designer rather than assuming the published total power figure is sufficient for board design. On upper floors, coordinate with the structural engineer as well: a filled shell of this size imposes a significant imposed load plus live loading from bathers, and the slab or transfer beam has to be verified for it.
Score what the supplier handles beyond the product
For multi-property developers, the swim spa is one line in a much larger procurement. It is usually easier to administer when the same counterparty also supplies the surrounding poolside furniture, the terrace finishes and the guest-room fit-out. That is the practical reason to consider a one-stop project furnishing supplier for this scope: fewer interfaces, one set of shipping documents, one coordination contact through installation.
Test the claim in the proposal itself. A supplier that describes turnkey delivery should be able to state, in writing and per project, who handles freight and customs clearance, who delivers to site, who sets the unit on its prepared base, who connects services and who remains responsible during the defects period. Where the scope is genuinely coordinated, covering design consultation, manufacturing and quality control, logistics, then installation and after-sales support, the coordination cost you carry internally drops accordingly. Where it is not, price the interfaces you will have to manage yourself.
If your project needs a different geometry because of a curved terrace or an irregular podium edge, ask whether a customized shape outdoor spa is a realistic alternative to forcing a standard shell into an awkward footprint. Custom shell geometry usually costs more in engineering time than it saves in wasted deck area, so make that trade-off deliberately.
Compare whole-life cost, not purchase price
A commercial swim spa earns its keep through availability. Build a simple comparison sheet for each proposal covering: energy to reach and hold operating temperature under your assumed ambient conditions; filtration run hours; chemical and dosing consumption; expected wear parts and their replacement prices; and the warranty terms actually quoted, including what is excluded in commercial use.
Insulation package and cover option deserve particular attention here, because they are frequently the cheapest line items to upgrade at quotation stage and the most expensive to retrofit after installation. A proposal that omits them from the base price while competitors include them is not cheaper; it is incomplete.
A short checklist before sign-off
- Dimensioned drawing with revision number, matched to the site survey.
- Equipment schedule naming every fitted item and clearly separating options from standard scope.
- Electrical data for the exact configuration: full-load current, phases, protection requirements.
- Written confirmation of who prepares the base, sets the unit, connects services and commissions the system.
- Freight terms, packaging specification and lifting assumptions to site.
- Warranty wording for commercial duty, plus spare-parts availability and response arrangements.
A proposal that answers those six points can be compared honestly against its competitors. One that does not will generate variations later, and variations on a completed terrace are far more costly than clarifications requested before award. For the full swim spa range and to request project-specific configuration data, review the Swimming Pools and Swim Spas section or contact the SANTERSON project team.