Open shelving is unforgiving. There is no door to hide a mismatched edge, a shelf that reads too yellow under the bathroom light, or an edge band that catches the eye from half a metre away. That is exactly why we recommend reviewing physical finish samples before we cut a single panel for your Santerson Freestanding Open Shelves. A sample you can hold, wipe and light properly settles arguments that drawings and photographs never will.

The process below is the one our project team follows for villa, apartment and hospitality bathrooms. It takes a few days, costs very little next to the value of the joinery package, and it protects both your sign-off record and our production run.

1. Fix the specification before you ask for a sample

A sample made against a vague brief only proves that something was made. Before we prepare anything, send us the information your drawing set should already carry:

  • Overall height, width and depth of each unit, plus the shelf pitch you want between open bays.
  • Board substrate and surface material for the visible faces, and whether the carcass interior matches or is a lower-cost alternative.
  • Edge treatment: matched edge band, contrasting band, or a solid-wood lipping on shelf fronts.
  • Frame or support detail, including any metal frame, glass panel or integrated lighting channel.
  • What the shelves will carry, such as towels and linen, glassware, ceramics, or product display in a guest bathroom.

Our Open Shelving and Tall Cabinets ranges are made to measure, with finish, layout and dimensions specified per project. Loading capacity, board thickness and any glass or lighting detail need confirming for each configuration rather than assumed from the catalogue page.

2. Ask for the sample set that matches how the unit will be seen

A flat offcut is not enough for open shelving, because most of what you notice is a front edge and a shadow line. We suggest requesting:

  • A face panel showing the surface colour and texture at full scale, large enough to judge grain direction and sheen.
  • An assembled corner or edge sample that shows the banding, the joint and the reveal between shelf and side panel.
  • A loaded shelf mock-up where span, board thickness and deflection matter to your specification.
  • Hardware on the actual finish: brackets, pins, frames or handles as they will be supplied.

If your scheme also includes Santerson Open Shelf Tall Cabinets or Santerson Corner Open Shelving in the same room, request those samples together and from the same batch. Colour and texture can vary between production runs, and matching everything at sample stage is far cheaper than matching it after delivery.

3. Judge the sample on site, not in the office

Finish reads differently under every light source. Take the sample to the actual bathroom or to a room with the same lamp colour temperature and wall finish, then check it at three moments: morning daylight, artificial light at night, and the low light when the room is unlit and the shelving is silhouetted.

What to checkHow to check itWhy it matters for open shelves
Colour and sheen matchPlace the sample against the vanity, door, wall panel and floor finish already selected.Open shelving sits in front of these surfaces; a slight colour shift is visible across the whole wall.
Edge and joint qualityRun a fingernail along the banding and sight down the shelf edge at eye height.Shelf fronts are at eye level, so a raised seam or glue line shows up immediately.
Surface behaviourWipe with a damp cloth, then with the cleaning product your maintenance team plans to use. Check fingerprints and scuff marks.Open shelves are touched constantly and cleaned far more often than closed doors.
Moisture responseCheck edge sealing on all four sides of the sample, and ask which substrate is specified for wet-zone bathrooms.Bathrooms cycle through humidity; unsealed edges are where swelling starts.
Shelf span under loadLoad the mock-up with representative items and sight along the front edge for visible sag.Sag is obvious on an unsupported open run, so span and thickness need agreeing now.
Hardware alignmentAdjust the pins or brackets and confirm the shelf sits level in the frame.Adjustable shelves must stay level after a few re-arrangements over the project life.

4. Sign the sample properly

Verbal approval causes disputes. When you are satisfied, do three things: mark the sample with the project code and date; photograph it next to the finishes it was matched against; and send us a written confirmation naming the material, colour reference, edge detail and the units it applies to. We keep that approved sample as the production reference, and every unit is checked against it before packing.

If something fails, say what you want changed in specific terms, for example warmer and less grey, a lower sheen, or banding flush with the surface, and we will return a revised sample. One extra round at this stage is normal; one extra round after production is expensive.

5. From approved sample to delivered shelving

Once the sample is signed off, the workflow follows our standard project route: measurement and drawing confirmation, quotation and detail confirmation, then production with quality control against the approved reference, packaging and container loading, door-to-door delivery, and installation with an inspection walk-through. Because open shelving is a made-to-measure item, dimensional sign-off happens at the same time as finish sign-off, so wall flatness, floor level and any tiled recess are resolved before manufacture rather than on site.

Where your project needs matching storage elsewhere in the property, the same approved finish carries across to Santerson Open Display Units in living areas and Santerson Freestanding Cabinets in bathrooms and laundry zones, so one sample sign-off covers the whole joinery set.

Send us your drawings and we will prepare the samples

If you are specifying open shelving for a villa, apartment or hospitality bathroom, send us the room drawing, your finish shortlist and the intended loading. We will advise on substrate, edge detail and shelf span for the configuration you need, then produce the sample set for site review before production begins.

Talk to our project team about custom furniture design and prototyping, or browse the SANTERSON product range to shortlist finishes for your next project.