A high gloss lacquer kitchen can look flawless in a render and still cause trouble on site. The reflections that make the finish attractive also reveal misaligned doors, uneven light lines and edge work that was never specified. Procurement teams rarely lose money on the door panel itself; they lose it on what nobody wrote down before production started. This guide sets out the records worth having in a purchase file for high gloss lacquer cabinets, so that approvals, tolerances and site conditions are agreed while they are still cheap to change.

Why the finish changes the paperwork

Lacquer is a sprayed, multi-layer finish that is polished after curing. Compared with foil-wrapped or laminated panels, it depends far more on process control: substrate preparation, spray passes, dust control in the booth, drying time between coats and final polishing. That has two practical consequences for procurement.

First, colour and sheen are matched per batch. Two production runs of the same RAL or brand colour code can read differently under the same luminaire if the polish level or coat count differs. Second, gloss surfaces amplify installation error. A two-millimetre rack misalignment that disappears on a matte door becomes a visible step and a shadow line between glossy panels.

The documents below exist to remove both risks before they reach the site.

1. The approved finish sample, not the colour name

Colour codes are a starting point, not an approval. For every lacquered door and panel in the order, the purchase file should hold a physical sample that both sides have signed and dated, with the following recorded on it:

  • The colour reference actually used by the factory (brand, code and base), plus the project name and batch it applies to.
  • Sheen level as a measured gloss value or an agreed descriptive band, together with the sample that demonstrates it.
  • Substrate and construction behind the finish — door thickness, substrate type, edge treatment and whether edges are sprayed or wrapped.
  • Which face is the show face on double-sided doors, and how reversing hands affects grain-free gloss panels.

Keep one signed pair of samples: one stays with the buyer, one with the manufacturer. When a variation order or a second phase arrives months later, that pair is the only reliable reference for matching what has already been installed.

2. Made-to-measure dimensions and who verified them

Lacquer cabinets in project work are almost always made to measure: sizes, layout and door split are set to the individual space rather than chosen from a modular range. That flexibility is the reason the finish works in villas and apartments at all, but it shifts responsibility onto dimensional accuracy.

For each kitchen, record who took the site dimensions and when, whether the survey happened after floor and wall finishes were complete, and which drawing revision the workshop cut from. Note the ceiling line, floor level and service runs that constrain the tall units, plus the tolerance band allowed at the reveal between run of cabinets and the finished wall. A written handover from the site team to the workshop closes the most common gap in bespoke joinery procurement.

3. Hardware schedule and door weight

Gloss doors are heavier than the flat panel they look like, and their faces cannot be re-drilled without a visible repair. Specify hinges, slides, lifts and handles in the same file as the doors, with the load rating matched to door height and weight, and confirm whether cup drilling is done at the factory or on site. Where handleless or integrated profiles are chosen, record the profile system and how it is fixed, because a late change usually means replacing whole panels.

A short hardware table prevents most of these arguments: item code, supplier, load rating, quantity per unit, and whether the hardware ships with the cabinets or arrives separately.

4. Site conditions that a gloss finish cannot forgive

Where these cabinets are installed matters as much as how they were built. Record the lighting layout before final door sizes are fixed, because overhead linear lighting running parallel to a run of doors shows every deviation; perpendicular fitting hides it. Note adjacent heat and moisture sources — ovens, hobs, dishwashers, wet areas — and confirm with the manufacturer which zones around them need protection or ventilation as specified for the product.

For apartments and hotels, also record access: lift dimensions, stair widths and corridor turning points. Oversize gloss panels cannot be cut to fit on site without destroying the finish, so delivery route is a commercial item, not a logistics detail.

5. Protection, sequencing and handover

Gloss panels are usually the most easily marked item in a room that other trades are still working in. The file should state when cabinets are installed relative to painting, flooring and stone work; how panels are protected during the remaining works; and what counts as acceptable on completion. A snag list signed by both parties at handover, listing each unit number and defect, is what makes later rectification an instruction rather than a negotiation.

Document set at a glance

Record Why it earns its place in the file
Signed physical finish sample (colour, sheen, substrate, edge detail) Matches future batches and variation orders to what is already installed
Dimensional survey with date, surveyor and drawing revision Fixes responsibility for sizes on bespoke, made-to-measure units
Hardware schedule with load ratings and drilling method Protects faces that cannot be re-drilled; matches hinges to door weight
Lighting, heat and moisture coordination note Controls reflection lines and confirms protection zones around appliances
Access and delivery route record Oversize panels cannot be resized on site without ruining the finish
Protection plan and signed snag list Turns defects after handover into a defined rectification scope

Where the specification flexibility sits

Because these cabinets are made to order, finish, layout and dimensions can be specified per project rather than fitted to a fixed catalogue module. Separate matte and two-tone lacquer cabinet lines exist for projects that want the same construction with a lower-sheen face, and matching lacquer wardrobe doors let a project carry one finish language from the kitchen into bedroom joinery — see matte lacquer cabinets and high gloss lacquer wardrobes. Where cabinetry is one line in a wider fit-out, coordinating it with other interior fixtures under a single supplier and drawing set reduces the number of interfaces where dimensions are usually lost.

Before placing the order, confirm in writing what each document covers: dimensions to be re-verified on site after finishes, the gloss value of the approved sample, hardware load ratings against actual door weights, and the protection and snag process. Every one of those items is free to agree at quotation stage and expensive to settle after panels are sprayed.

A procurement file for high gloss lacquer cabinets does not need to be long. It needs to name the approved sample, the verified dimensions, the hardware that carries the doors and the site conditions those doors will live in. Teams that lock those four things down before production rarely spend their project budget on remedial visits.