Freestanding open shelving looks simple on a drawing until it arrives on site out of square, with the wrong substrate behind the finish, or fixed to a wall that was never meant to carry a load. For Australian villa, apartment and hospitality projects, the verification work happens before the purchase order, not during handover. The checklist below follows the same sequence we use when specifying Santerson Freestanding Open Shelves for a project: scope, fixing method, substrate, load, finish, documentation, packing and after-sales.
Start with the definition: freestanding or fixed?
The first thing to settle is what the drawing actually shows. A floor-standing unit carries its own weight through a base frame or plinth and can be moved during a fit-out. A wall-hung shelf carries everything through brackets into the wall, so the substrate becomes a structural question. Some designs combine both: a base-supported run with an upper section tied back to the wall for stability.
Ask the supplier to state, in writing and per item, whether each unit is freestanding, wall-mounted or mixed, and what fixing hardware is included. If the specification says freestanding but the shop drawing shows a bracket into the wall, that discrepancy needs resolving before production starts.
Confirm substrate and fixing method for every mounting point
For anything fixed to a wall, send the wall build-up: stud framing, brick, double brick, Hebel, tile over render, or a framed partition with a lining. Anchors that behave well in solid masonry are not automatically suitable in a lightweight partition, and an exposed fixing detail on a tiled surface is a visible defect as well as a structural one.
Request the fixing detail per mounting condition — anchor type, embedment, whether timber nogging or a backing frame is required behind the finished surface, and who supplies that blocking. On a bathroom or laundry run this matters twice over: wet-area walls are frequently lined with water-resistant plasterboard or tiled, and shelf fixings must be set out to miss waterproofing penetrations and services.
State the load case in kilograms, not adjectives
“Heavy duty” is not a specification. For each bay, record what will sit on it and at what depth: towels and linen, glassware and decanters, books and catalogues, planters, or equipment. Then ask the manufacturer to confirm shelf thickness, span between supports, deflection limits under that load, and the load path through side panels, dados or brackets.
- Uniform distributed load per shelf, in kilograms, plus a point-load statement for concentrated items.
- Maximum unsupported span at that load, and whether a mid-span support is required above it.
- Top-fixing versus side-fixing hardware, and whether adjustable shelf pins are rated for the stated load.
- Overturning resistance for tall narrow units: wall tie, ballast, or a base that is fixed to the floor.
For tall open runs in guest rooms and spa areas, overturning is the risk most often missed. A unit loaded top-heavy and left untied will move. Confirm whether the fixing detail includes an anti-tip connection and what surface it must connect to.
Specify the substrate behind the finish, not just the finish
Two units can look identical in a render and perform completely differently on site. One is MDF with a melamine laminate; the other is a moisture-resistant board or plywood core with lacquer or veneer. In bathrooms, laundries and poolside zones where humidity swings, the core matters as much as the surface.
For any project item, ask for: the core material and its density; the face material and edge treatment; whether edges are ABS, PVC, lacquered or veneer-wrapped; and whether all six faces are sealed where the unit sits in a wet area. Where the site environment is genuinely damp, ask directly whether the specified board is suitable, and get the answer in writing.
Treat made-to-measure as a documentation exchange
Configurable open shelving is usually supplied to project dimensions rather than catalogue sizes. That flexibility only pays off when the measurement record is complete and signed off by one party.
- Overall: height, width and depth per unit, plus floor-to-floor and finished-floor levels.
- Setout: shelf spacing, bay widths, position of any fixed shelf, and tolerance for out-of-plumb walls.
- Interfaces: skirting returns, cornices, architraves, power points, lights, towel rails and doors that swing into the run.
- Sign-off: one dated shop drawing per unit type, initialled by the person authorised to approve it.
Re-measure on site after linings and finishes are in place. Dimensions taken off a drawing that predates the plasterboard and tile build-up will be wrong by the thickness of both, and open shelving has nowhere to hide that error.
Match the range to the room before comparing prices
Open storage is specified across very different conditions on one project, and the environment changes what should be ordered. Bathroom and laundry runs sit in humidity and need sealed edges and a wipeable finish. Study and living joinery carry heavier distributed loads over longer spans. Bedroom wardrobes are usually lighter but demand tighter tolerances against doors and hanging rails.
| Application | What to verify first | Santerson range reference |
|---|---|---|
| Bathroom and laundry open storage | Humidity exposure, core board, edge sealing, clearance to basin and mirror | Santerson Open Storage |
| Floor-standing display and linen runs | Base detail, overturning restraint, plinth interface with floor finish | Santerson Freestanding Cabinets |
| Wall-hung shelving over vanities and desks | Substrate, bracket type, load per shelf, bracket spacing | Floating Shelves |
| Built-in and floor-to-ceiling joinery runs | Setout against walls and ceiling, mixed open and closed bays, service access | Wall Panel Systems |
| Fitted wardrobe shelving | Rail heights, shelf depth, door clearance, drawer interfaces | Shelf Focused Modular Wardrobes |
Comparing quotations only works when every line is priced on the same build-up. Put the core material, edge treatment, shelf thickness, span and hardware schedule in one table across all bidders, then compare.
Ask what documentation comes with the goods
Australian consultants increasingly ask for material declarations before approving joinery. Ask your supplier which documents they can provide for the specific item: board grade and formaldehyde emission class, finish system and its technical data sheet, hardware make and load rating, and a compliance statement where one is claimed. Where a certification is quoted in marketing material, ask for the certificate itself and check that it covers the product being shipped.
This is also where conflicting figures surface. A supplier website may quote factory area, staff numbers or export share differently across pages. None of that tells you whether your joinery will be built correctly, but a clean document pack does indicate production discipline.
Plan packing, sequencing and site access before the container ships
Open shelving is long, flat and easy to damage in transit. Agree the packing standard per component: panel thickness protection, corner protection, edge banding guarded, glass shelves crated separately, and hardware bagged and labelled against each unit number.
- Unit numbering on every crate matched to the signed shop drawings, so the site crew knows what goes where.
- Delivery sequencing by room or level rather than one undifferentiated drop.
- Access route confirmed: lift dimensions, stair widths, and whether crates fit the service entrance.
- Inspection on arrival, with damage photographed against the packing list before installation begins.
For international shipments, confirm in writing who handles customs paperwork, what Incoterms apply, and where your responsibility for damage ends. Transit time and duty treatment vary by consignment, so get both confirmed for your order rather than relying on general marketing claims.
Close the loop with installation and after-sales terms
Decide before ordering who installs. If the supplier provides on-site installation, confirm installer availability in your state, what the snag list covers, and the warranty period and exclusions in writing. If a local joiner installs, confirm that fixing holes and hardware are pre-machined to the shop drawing so the trade is not making decisions on site.
Either way, agree how replacement parts are handled — spare shelves, pins and brackets — and how quickly they can be produced. A single damaged shelf out of a villa's open shelving run should not require a new container.
How SANTERSON supports this verification process
SANTERSON is a China-based furniture and building materials manufacturer supplying project customers internationally, with Australian villa and apartment references including projects in Willoughby, North Turramurra, Perth, Melbourne and Sydney. As a furniture and building materials supplier for Australian projects, we work from your drawings rather than a fixed catalogue: made-to-measure dimensions, selectable cores and finishes, and shop drawings issued for sign-off before production.
Because shelving usually sits in the same package as vanities, wardrobes, wall panelling and doors, coordinating it through one one-stop project furnishing supplier removes a whole class of interface problems. The same factory cuts the joinery that the shelf run is built into, so tolerances, finishes and edge details are decided once instead of being reconciled between two subcontractors.
Send your drawings through our contact page, or speak with PHILLIP on WhatsApp +86 139 2821 4007 to review a shelving package for an Australian project.