A pair of classic French double doors can carry the look of an entire villa entrance hall or guest suite. The mullion proportions, the shadow line of the glazing bars, the warmth of the timber tone and the way the leaves sit in the frame are all decided long before the first leaf reaches site. Once production starts, changing a finish means rework, delay and extra cost. That is why we ask every project buyer to approve physical Classic French Double Doors samples before we release the order to the line.

This guide walks through what a sample pack should contain, what to check on each piece, and how sign-off is recorded so that the doors you receive match the doors you approved.

Why finish samples matter more on double doors than on single leaves

Double doors put symmetry under scrutiny. Two leaves sit side by side, and any variation in grain direction, sheen level or stain tone between them becomes obvious the moment daylight falls across the opening. French doors add a second variable: glazing bars divide the surface into narrow stiles and rails, so a finish that looks even on a wide panel can read as patchy along a slim moulding.

Because our doors are made to measure for each project — with custom furniture design and prototyping available where a drawing calls for a bespoke profile — the approved sample, not the catalogue photograph, becomes the reference for the whole batch. For a villa or hotel job with a whole floor of openings, that single panel decides whether every set matches.

What to request in the sample pack

Before we quote final quantities, ask for a pack that represents the actual build-up rather than a single colour card. A practical pack for this door type includes:

  • A stained or painted sample on the specified substrate, large enough to judge grain and colour at arm's length rather than at thumbnail size.
  • A short section of the moulding profile, so you can see how the finish sits on arrises, in the recessed panel groove and along the glazing bar edge.
  • The glass or glazing option under consideration, held against the frame sample to check how the frame tone reads through the light.
  • Handle and leaf-edge details where these are part of the specification.
  • The same finish in two sheen levels if the design intent is still open, so the choice is made on evidence.

Request the pack as early as the drawing stage. Sample production runs in parallel with dimensional confirmation, and both need to be closed before the order enters manufacturing.

Six checks to run on every sample

  1. Colour under your own light. Do not judge a finish in a showroom or on a phone screen. Hold the sample in the room where the doors will hang, at morning and afternoon light, and against the flooring and skirting already specified for the project.
  2. Sheen and surface texture. Matte, satin and gloss behave differently on a moulded profile. Run your hand along the arris; a finish that feels chalky or heavy on the edge will look worse on a full-height leaf.
  3. Grain consistency across two leaves. Ask for two samples of the same finish and place them side by side. If they do not read as one family, the batch will not either.
  4. Profile detail. Check that paint or stain has not filled the moulding line. On classic panelling, a rounded, over-filled edge loses the crisp shadow line that makes the design read as traditional rather than generic.
  5. Frame-to-leaf relationship. Look at the sample next to the architrave or frame section. Flush alignment and reveal depth are decided here, not on site.
  6. Wear resistance for the location. A lobby or high-traffic corridor leaf takes knocks that a bedroom leaf never will. Confirm with our team which finish build-up is specified for those openings.

Check the dimensions at the same time as the finish

A finish approval is only half of sign-off. French double doors depend on tight coordination between opening size, floor level, and the threshold or carpet detail below. When you review the sample, confirm the following against your setting-out drawings:

  • Clear opening width and height for each pair, taken from the finished floor level, not the structural slab.
  • Which leaf is active and which is fixed, and how the two leaves meet at the centre.
  • The meeting-stile detail at the centre, including any coordination hardware you intend to specify.
  • Glass thickness and glazing-bar spacing, measured on the sample section rather than assumed from a drawing.

Our doors are supplied with made-to-measure sizing and material and finish options, with the layout tailored to each project. Dimensions and selected specifications are confirmed for every order before production, so a discrepancy caught at sample stage costs nothing; the same discrepancy found after manufacture becomes a re-run.

How to record the approval so it survives the handover

Most disputes in door procurement come from a verbal sign-off that nobody can reconstruct months later. Treat the sample as a document:

  • Number each sample and write the project reference, opening list and finish code on the back or on an attached tag.
  • Photograph the sample in place against the flooring and wall finish, and file that photo with the drawing set.
  • Have the same person — architect, contractor or client representative — sign both the finish and the dimensional sheet, so responsibility is not split across three parties.
  • Keep one approved sample on site. It is the fastest way to settle a question during installation, and it lets you check a later leaf against the original reference.

Where these doors sit within a wider fit-out

Doors rarely arrive alone. In a villa or hospitality package they are specified alongside joinery, wall panelling and cabinetry that share the same stain or lacquer. Where the design calls for a matching tone across several elements, review the door sample next to the samples for those items at the same meeting — turnkey villa furnishing work is easier to keep consistent when finishes are signed off together rather than category by category.

If your project also includes hinged openings in a plainer profile, or concealed doors that disappear into the wall line, request those samples in the same round. Comparing options side by side at sample stage avoids a second approval cycle later.

Bringing it together

A finish sample review is a short step that prevents months of correspondence. The discipline is simple: request a pack that shows the real build-up, judge it in the room where the doors will live, check dimensions while the sample is in hand, and record the sign-off so it can be traced through to delivery. Do that, and the pair of classic French double doors you open on site is the pair you approved on paper.

Send us your opening schedule and finish references, and we will prepare the sample pack with the profile sections and glazing options for your specific project before the order goes into production.