A shelf-focused modular wardrobe looks simple on a rendering and complicated on site. Fixed shelf heights that worked in the design intent drawing clash with the ceiling level the contractor actually built, the skirting the joiner has to scribe around, or the depth of the finished floor build-up. The result is a run of cupboards that closes on paper but does not store what the client planned to store. Below is the coordination sequence we follow on residential wardrobe projects, from the first marked-up plan to the handover checklist, so Shelf Focused Modular Wardrobes arrive ready to install rather than as a site problem.
What a Shelf-Focused Layout Is Actually For
A shelf-focused layout places the working depth and vertical spacing of the carcass around folded items, knitwear, towels, linens and boxes — the things that stack rather than hang. It suits bedrooms with limited floor area where a full hanging run would eat the walking space, dressing rooms that sit next to a separate hanging zone, and spare or guest rooms where storage is mostly seasonal.
It also fails predictably when the shelf pitch is copied from a generic detail. A 320 mm pitch wastes half the height under jumpers; a 450 mm pitch buries folded T-shirts in dead air and makes the middle shelves awkward to reach. The coordination work, therefore, is not choosing between shelves and hanging — it is fixing the vertical rhythm against the real room.
Before Drawings: The Brief That Fixes Shelf Pitch
Ask the client or project architect for a storage brief before any carcass is drawn. Three answers change the layout more than anything else:
- Hanging versus folding split. If most of the wardrobe content hangs, shelves should be concentrated in the lower zone and above the hanging rail — not spread evenly through the run.
- What sits on top shelves. Suitcases, boxed storage and off-season bedding need a clear internal height set once and kept consistent, instead of an arbitrary top shelf.
- Drawer or basket requirement. Where socks, folded underwear and small items must live decides whether the base is drawers, baskets or a fixed plinth. Our Drawer Focused Modular Wardrobes are the version to reference when that lower zone carries most of the load.
Where the brief is genuinely mixed, a Combination Modular Wardrobes layout — shelved bays at the ends, hanging in the middle — usually resolves it without a second wardrobe.
Reading the Drawings: Four Dimensions to Confirm on Paper
Once the design intent drawing exists, check these four numbers before the carcass is released for production. Each one is a common source of rework.
| Dimension | What to confirm on the drawing | Typical consequence if missed |
|---|---|---|
| Floor to ceiling, measured at both ends of the run | The finished floor level and the true finished ceiling level, not the structural slab and deck | Carcase too short for a flush top, or an scribe cut that breaks the shelf line |
| Clear internal depth after doors and hardware | Carcass depth less door thickness, hinge or sliding track, and any wall return | Folded stacks overhang the front edge; sliding doors bind on handles |
| Vertical position of every fixed shelf | Whether the pitch is set to the client's storage list rather than a default module | Wasted height, or shelves that will not take the intended items |
| Setting-out against openings and services | Door swing, switches, downlights, air-conditioning grilles, skirting and architraves | Doors foul the wardrobe; a grille is blocked; scribing becomes visible |
Mark the answers directly on the drawing and return it for confirmation. A dimension queried in writing costs one email; discovered on site it costs a rebuilt bay.
Site Requirements That Change the Carcass
The second pass happens against what is actually being built. Before final sign-off, confirm with the site team:
- Floor build-up and level. Tolerance across the run determines whether the base is set on adjustable legs behind a removable plinth or packed and scribed on site.
- Wall condition. Out-of-plaster walls need a scribe or a reveal; the detail must be drawn so the shadow line falls where it can be seen but not criticised.
- Skirting, architrave and cornice. Decide whether the carcass is cut around them or they are removed and replaced after installation. Both work — but only if agreed before the joinery is made.
- Lighting and power. Internal lighting needs a cable route and a driver location that stays accessible; downlights must not sit where a shelf will cover them.
- Door interface. Hinged doors need clearance to handles, adjacent walls and any bed or nightstand. Sliding doors need the track zone kept clear along the full run.
- Access route. Confirm the assembled module size against lift openings, stair turns and door widths — a single tall carcass may need to be split into two bays with a field joint.
Making a Modular System Behave Like Built-In Joinery
Modular wardrobe components are made to measure — sizing, material and finish are specified per project, and the layout is tailored to the space. That flexibility only pays off if the module boundaries are set where they read as built-in:
- Put a module joint at a natural break — a change of bay, a corner, or behind a door stile — never mid-shelf.
- Keep shelf lines continuous across adjacent modules by aligning the pitch to the same datum from the finished floor.
- Specify the finish for interior faces as well as fronts; open and glass-fronted layouts expose carcass edges, so interior material matters as much as the door.
- Detail the top closure against the ceiling and the base against the floor on the drawing, not at the bench.
For a run with an awkward corner or a niche, the same discipline applies: draw the return first, then set the shelves to it. Open Modular Wardrobes make this easier to see during coordination, because every shelf line is visible before the doors hide it.
Finish and Hardware Sign-Off
Fix finishes against the room's other timber and metalwork — flooring, door joinery, kitchen cabinetry — under the same light the room will have. Then confirm hardware against use, not appearance:
- Shelf supports. Peg systems are flexible but sag over long spans; specify shelf depth and span so the fixing type is chosen deliberately.
- Doors. Hinged for full access and simple alignment; sliding where the room cannot absorb a door swing.
- Soft close and handles. Decide per bay — heavy shelved doors need closer hardware specified at order, not added later.
Where finishes are bespoke to the project, this is the stage handled under Custom & OEM Service: material and texture selection, prototyping and sample approval before the production run.
Delivery, Installation and Handover
Sequence the joinery with the trades around it. Wardrobes go in after painting and flooring are complete, after the ceiling set-out is fixed, and before final dressing of the room.
- Check pallet contents against the bay schedule on arrival, with panel numbers matched to the drawing.
- Confirm each carcass is level and plumb along the whole run before fixing — a twist shows up as a stepped shelf line.
- Set door alignment and gaps, then re-check after the scribe or reveal is closed.
- Test every shelf for deflection under load and every drawer or basket for smooth travel.
- Record on the snag sheet: dimensions as built, finishes as supplied, hardware model, and any field-modified bay.
That record matters on a multi-unit job. When the same layout repeats across bedrooms or apartments, the as-built note tells you which bays were adjusted on site, so the next unit is made right the first time rather than corrected again.
A Short Pre-Order Checklist
- Storage brief confirmed: folded, hung and boxed items listed with target internal heights.
- Floor-to-ceiling height measured at both ends of the run, from finished surfaces.
- Clear internal depth stated after doors and hardware.
- Fixed shelf positions dimensioned on the drawing from a single floor datum.
- Skirting, cornice, lighting, grilles and switch positions shown and coordinated.
- Module joints located at bay breaks with continuous shelf lines.
- Interior and exterior finishes specified and sample-approved.
- Access route checked against the assembled module size.
- Installation sequence agreed with painting, flooring and ceiling trades.
Send us the marked-up plan, the measured levels and the storage brief, and we will return a wardrobe layout with shelf pitch, carcass sizes and finishes set to your site conditions — then coordinate production and on-site installation against the same drawings.