A set of partition sliding panels looks finished the day the installer walks out. The real test starts two years later, when a panel drags along the track in a villa media room, a replacement roller cannot be matched to the profile, or the site team has no idea who tightens the hardware. Because these systems are made to measure and assembled from tracks, hangers, panels and finishes chosen per project, after-sales support is not an appendix to the order — it is part of the specification. Below is the checklist we ask buyers to work through before they place a partition sliding order, using Santerson Partition Sliding Systems as the reference product.
Why sliding partitions age differently from fixed joinery
Fixed cabinetry fails quietly and rarely moves. A sliding partition carries its own weight along a track every time someone opens or closes it, and the moving parts — hangers, bottom guides, buffers, the track itself — are the items that eventually need adjustment or replacement. Panel size makes this worse: the taller and wider the leaf, the more load sits on each hanger over years of use.
The second difference is accountability. A partition wall may be supplied by a joinery workshop, the track by a hardware brand, and the installation by a local contractor. When something goes wrong, three parties can each point at the other two. Single-source supply removes that argument, which is why we recommend buyers confirm who owns the whole assembly — panels, track, hardware and finish — before the order is placed.
Question 1: Which exact configuration was delivered?
Partition sliding systems in this range are configurable listings rather than fixed catalogue items. Finish, layout and dimensions are specified per project, and the same collection also covers acoustic sliding panels, glass sliding panels and textured sliding panels. Each of those needs different hardware assumptions, so a generic "sliding wall" note on a purchase order is not enough to support a later claim.
Ask for the delivered configuration to be written back to you in one document: panel type and finish code, opening layout and number of leaves, track type and mounting method (ceiling-hung or floor-supported), panel height, width and weight per leaf, plus the glass type where glass panels are involved. That document is what both sides refer to when a spare part is ordered years later.
Question 2: What happens when a roller, guide or track fails?
This is the question most buyers skip and the one that matters most. Get specific answers on four points:
- Whether replacement hardware — hangers, bottom guides, buffers, track sections — can be ordered as spares after delivery, and for how long.
- Whether the hardware is a standard profile you can source locally, or a proprietary part that only the supplier can provide.
- How many spare sets ship with the original order, and whether they are packed in a labelled box rather than loose in a container.
- Who pays freight on a replacement part, and how it is shipped — courier, consolidated container, or next project shipment.
SANTERSON lists spare parts and replacement alongside warranty coverage in its installation and after-sales support. Treat the scope, duration and exclusions of that coverage as project-specific terms to confirm in writing on your own order, not as a blanket guarantee — response-time figures published on a website are marketing statements until they appear in your contract.
Question 3: Who adjusts the system after handover?
Sliding panels drop out of alignment for ordinary reasons: floor settlement, a track that collected dust, a buffer that shifted, or leaves that were forced against their stop. Someone has to re-level and re-adjust them.
Ask whether on-site installation includes a post-handover adjustment visit, whether snag lists raised at handover are closed out before final sign-off, and what remote support looks like when no local technician is available. Practical video guidance from the factory — which screw to adjust, which direction, what clearance to leave under the leaf — solves most of these cases without anyone flying in. Confirm that guidance exists before you need it.
Question 4: What does the warranty actually cover?
Wording matters more than length here. A sliding system has two very different failure classes, and a single "X year warranty" sentence often hides which is which:
- Panel and finish: surface integrity, edge banding, warping, discolouration, delamination of the panel itself.
- Mechanism: track, hangers, guides, buffers, and whether they are covered for a defined number of cycles or simply "under normal use".
Also ask what voids cover. A panel that has been shortened on site, a track fixed into a substrate that was not the one specified, or hardware loaded beyond the stated per-leaf weight are common reasons a claim is refused. If your site team intends to trim or re-hang anything, get written agreement first.
Question 5: How do you maintain finishes and glass over time?
Maintenance instructions should arrive with the product, not be invented later by a cleaning contractor. Ask for the cleaning method for each finish you ordered — wood veneer, laminate, lacquer, textured surface or glass — and for the glass panels specifically, confirm the glass type and the safety requirements that apply in your market before installation.
If the partition doubles as a room divider near a bathroom or wet area, ask how the base edge is sealed and what happens if water reaches the track. Where a wall integrates doors and panelling — for example integrated door and panelling or wood panel partitions — request matching touch-up material for the finish, so a repaired corner does not become visible.
Question 6: How are spares shipped and documented?
A spare part that cannot clear customs is not a spare part. Ask whether replacement hardware ships with a commercial invoice and packing list, whether the shipment is trackable, and how it fits into your existing delivery arrangements — SANTERSON handles freight forwarding by sea, air and rail with customs paperwork and door-to-door delivery under its logistics service, which is useful when a small replacement set has to reach a villa or hotel site on the other side of the world.
Ask for one more document at handover: an as-built sheet with opening dimensions, leaf weights and hardware references. That single page is what a facilities team uses five years later when they order parts without the original salesperson.
Question 7: Who answers, and how fast?
Named contact beats a shared inbox. Before the order, confirm who handles after-sales for your project, which hours that person works, and what channel — email, phone or WhatsApp. SANTERSON publishes its contact page with stated business hours of Monday to Saturday, 8:00 AM to 6:00 PM (GMT+8), and says enquiries receive a response within 24 hours; verify the current arrangement for your project rather than assuming it applies automatically.
Buyers coordinating several product groups on one site — joinery, doors, wall panelling, flush sliding doors and other fit-out items — gain most from a single after-sales owner. When the same supplier answers for the whole package, an adjustment call covers the interaction between systems instead of turning into a dispute about whose work is at fault.
A short pre-order checklist
- Delivered configuration written back: panel type, finish code, layout, track type, per-leaf dimensions and weight.
- Spare hardware list agreed, with quantities shipped in the original container and a labelled box on site.
- Warranty split into panel/finish and mechanism, with exclusions stated plainly.
- Post-handover adjustment visit or remote guidance confirmed.
- As-built sheet with dimensions and hardware references at handover.
- Named after-sales contact, working hours and channel recorded on the order.
None of these asks are unusual, and a supplier accustomed to project work will answer all of them without hesitation. If any answer is vague, that vagueness is your answer — clarify it in writing before production starts, while it still costs nothing.
Planning partition walls, sliding panels or other built-in joinery for a villa, hotel or office project? Send your drawings and opening dimensions to SANTERSON and the configuration, hardware and after-sales terms can be confirmed in writing before production.