A freestanding cabinet is one of the few pieces in a villa or apartment fit-out that gets judged at arm's length and from every angle. Because Santerson Freestanding Cabinets are made to measure, with finish, layout and dimensions specified per project, the sample you sign off before production is what protects that decision. This guide walks through what to request, what to check on the physical sample, and how to record approval so the production run matches what you reviewed.
Why a finish sample matters more for made-to-measure casework
Catalogue furniture lets you see the exact item before ordering. Made-to-measure storage does not. On our custom and OEM service, substrate, edge treatment, sheen level and hardware all come from a specification sheet rather than a showroom shelf, so a drawing cannot tell you whether a matte lacquer reads warm or grey under your own lighting, or whether a wood-grain figure breaks sensibly across a door stile. A physical sample converts an assumption into something you can reject.
The same logic applies to the display versions of this product family. A Santerson Freestanding Cabinet in a living area is read against flooring, wall panelling and lighting at the same time, so its finish has to be judged next to those other finishes rather than on its own.
Step 1: Fix the scope of each cabinet before requesting samples
Sample requests go wrong when the drawing is still moving. Before anything is cut, confirm for every unit:
- The room and role — bathroom storage in the bathroom fixtures range, a living-area display unit, or a media unit from the Santerson Freestanding TV Cabinets collection.
- Height, width and depth as agreed on site, including skirting, cornice, door swing clearance and any plinth or shadow gap.
- Interior layout: shelf heights, drawer count and pull-out direction, and whether open niches are visible from the main viewing line.
- Exposure the unit will actually live in — a bathroom cabinet sits near showers and cleaning agents, which is a different requirement from a hallway display piece.
Sample only what the finished item will contain. If the design pairs a carcass laminate with a lacquered door and a metal handle, request all three, otherwise you are approving a combination you will never see installed.
Step 2: Ask for the right sample set
For each cabinet line, ask for a package that covers the visible surfaces and the edges. A useful minimum:
| Sample | What it lets you verify |
|---|---|
| Door or panel face, large enough to read at 500 mm | Colour, sheen, grain direction, and whether the surface shows fingerprints or glare under site lighting |
| Edge band or wrapped edge in the same finish | Colour match between face and edge, joint line visibility, and tactile continuity along the front edge |
| Carcass or interior substrate offcut | Board thickness, core quality, and how the interior tone sits against stored items and any integrated lighting |
| Hardware sample — handle, pull, hinge or slide | Finish tone against the door, profile comfort, and fixing method |
| Glass or glazed panel where specified | Tint and reflectivity, and how contents read through it |
Request each sample with its specification reference written on the back: finish name, substrate, edge thickness, hardware model. Undocumented samples cause silent substitutions later, because nobody can prove which version was approved.
Step 3: Test the samples in the real room
Do not approve a finish on a factory light table. Take the set to the actual space and check it:
- Against the approved flooring, wall panel and countertop samples side by side — colour casts only appear in combination.
- Under daylight at two times of day, and under the room's own evening lighting, including any cabinet or niche lighting.
- From the standing eye line for tall units and from seated height for low units, since sheen and grain read differently at each.
- With a hand on the surface — matte finishes that look right in a photo can feel sticky or chalky in person.
Step 4: Score what you see against a short checklist
Write findings down as pass or fail rather than impressions. The points worth recording:
- Colour and sheen. Does the tone hold across the panel, and does the sheen level match the drawing note (matte, satin or high gloss)?
- Grain and pattern. For wood-effect and veneer finishes, check figure direction on doors and whether repeat patterns look deliberate at panel scale.
- Face-to-edge match. Compare the edge band in raking light; a visible tone step along a front edge is one of the most common complaints on site.
- Joint and corner quality. Look at how the sample is joined — gaps, overflow adhesive and chipped corners predict production quality.
- Hardware feel. Drawers should run without binding, doors should close without needing to be pushed home, and handle tone should match rather than sit beside the door colour.
- Cleanability. Wipe the sample with the cleaning agent the site will actually use and check for haze, lifting or colour change.
Where a finish fails, name the failure precisely — "edge band reads half a shade lighter than the door face in daylight" is actionable; "doesn't look right" is not.
Step 5: Record approval and lock it into production
Once the set passes, sign off with a dated record rather than a verbal nod. Keep for each unit type: the sample reference numbers, the room they belong to, the drawing revision they correspond to, and any agreed exceptions such as a reversed grain direction on a specific door. Send photographs of the approved set against the flooring and wall finishes so the production team and the site team are looking at the same reference.
We work from that record through one-stop furniture and building materials procurement: specification confirmation, production and quality control, then packing and shipment. If you want a second opinion on a combination of finishes, our interior design service covers material selection and coordination across the fit-out, so cabinet finishes are checked against flooring, panelling and lighting rather than in isolation.
Step 6: Plan the delivery and inspection around the approved sample
The last step happens before the goods arrive. Agree logistics and door-to-door delivery terms, unpacking sequence and storage location on site, so panels are not stacked against a wet wall while other trades finish. When the cabinets land, take the retained sample set to each unit and check finish, edge and hardware against it before installation is signed off — then record anything that needs attention while it can still be corrected at source.
For on-site fitting and any follow-up, our installation and after-sales support covers inspection and snags. Ask about the specific warranty terms, spare-parts availability and response arrangements that apply to your project when you confirm the order, since these vary by scope.
A quick pre-production checklist
- Dimensions, layout and exposure confirmed per unit, not per product family.
- Samples requested for face, edge, carcass, hardware and any glazing.
- Every sample labelled with finish, substrate and hardware reference.
- Reviewed in the real room, against approved flooring, panelling and lighting.
- Pass/fail notes recorded, with failures described specifically.
- Signed, dated approval tied to a drawing revision and kept for site inspection.