Open bookshelves look simple on a drawing. A run of shelves, no doors, done. In practice they are one of the easiest built-in items to get wrong, because everything that matters — span, depth, fixing, finish and how the unit meets the wall — is visible for years afterwards. If you are sourcing them from an overseas factory for a villa, apartment or hospitality fit-out in Australia, most of the risk sits in what you confirm before production starts, not after.

The checklist below follows the order we suggest working through it: the space first, then the product specification, then the commercial and logistics terms that decide whether the job lands cleanly.

Start with the room, not the catalogue

A shelf run is a fixed dimension in a real building. Before you compare finishes, take three measurements from site: the clear width and height of the wall, the depth you can actually afford once doors, skirting and services are accounted for, and the position of any power points, switches or downlights that will land behind or inside the carcass.

Then decide how the unit is carried. A floor-to-ceiling bookshelf that reaches a raked or bulkheaded ceiling needs a scribed top and a fixing detail agreed in advance, and it usually has to be built as panels that pass through the doorway. A wall-hung run depends entirely on what is behind the plasterboard: stud spacing, noggins, or a steel backing frame specified on the drawing. Freestanding units avoid that conversation but need floor space and an anchoring point.

Verify span, load and shelf depth together

Sagging is the most common complaint on open shelving, and it is a specification problem rather than a material one. Three variables interact: the unsupported span of each shelf, the thickness and core of the panel, and what the shelf is expected to carry. A 900 mm span holding paperbacks behaves differently from the same span holding display objects or heavy ceramics.

Ask the supplier, in writing, for the maximum recommended span at the shelf thickness they are quoting you, and for the load assumption behind it. Where a run needs to be wider than that limit, request intermediate verticals, a thicker shelf, or a modular bookshelf system whose frames carry the load instead of the shelves themselves. If you want books on one half and objects on the other, say so — the shelf pitch and depth should change between zones rather than stay uniform across the whole wall.

Depth deserves the same attention. Full-depth shelves in a living room quickly look heavy and waste space behind deep hardbacks; shallower shelves suit paperbacks and display but will not take large-format volumes. Decide shelf depth per zone, then confirm the carcass depth that follows from it.

Fix the finish specification in writing

Open shelving shows its edges. Two details separate a good result from an average one: how the panel edge is finished, and how consistent the colour is across panels produced in different batches.

  • Edge treatment — flush 2 mm edge banding, solid timber lipping or a mitred wrap. Ask which applies to visible shelf edges as well as cabinet ends.
  • Colour and grain reference — request the board manufacturer's code or a physical sample, not a photograph. Timber-look laminates and veneers vary noticeably between runs.
  • Sheen level and its tolerance, plus which face of a two-sided laminate is used where.
  • How the finish holds up to cleaning agents specified for the rest of the project. For a hotel or serviced-apartment job, ask what the supplier recommends for routine upkeep.

Order a sample board before you sign off production drawings. It is the cheapest objection you will ever raise, and it settles finish disputes before there is anything to argue about.

Decide what open shelving is actually for in this project

Dust, clutter and housekeeping are real costs over the life of a building. In guest rooms and high-use family areas, an all-open wall asks someone to tidy it constantly. The usual answer is a mix: open display where the eye goes, closed storage below or behind, and closed bookshelves for anything you would rather not dust weekly.

Where a display moment is the point, recessed niches in a wall or joinery run are often tidier than a freestanding unit, because the shelving becomes part of the surface rather than an object sitting against it. Glass-fronted sections do the same job while protecting contents — worth considering for anything on display in a commercial setting.

Lighting and services: settle them before the carcass is made

Integrated shelf lighting is a joinery detail, not an electrical one. It requires a rebate or channel in the shelf, a route for cable, a driver location that someone can reach for service, and a switch or sensor point agreed with the electrician. Retro-fitting strip light under a finished shelf leaves visible fixings and a driver nobody can access.

Send the electrical layout with your joinery drawings and mark on both which way they interact. The same applies to any media, sensors or downlights that fall inside the unit.

What to confirm with an overseas supplier before you place the order

ItemWhat a clear answer looks like
Drawings and sign-offDimensioned production drawings with your project reference, issued for signature before cutting starts. Confirm who signs and what happens if site dimensions differ.
Site verificationWritten confirmation of which party takes final site measurements, and how tolerance is handled on older or uneven buildings.
Panel and core specificationNamed board type, thickness and core for carcass, shelves and back panels — not just a colour name.
Fixings and assemblyHow the unit is assembled and fixed on site, what hardware is included in the crate, and whether an installer guide ships with it.
Packaging and packing listPanel-level labelling that matches the drawing numbers, so a crew can find each piece without guessing.
Delivery termsIncoterms, port or site delivery, duties and who clears customs. Get these in the same document as the price.
Spares and claimsWhat happens to a panel damaged in transit: replacement part shipped, credit, or a re-made section — and how quickly.
A practical note for any overseas purchase. Where a supplier's marketing pages quote figures such as factory size or export share without documentation, treat them as background rather than evidence, and base your decision on what you can verify for your own order: drawings, sample boards, packing list and delivery terms.

Ordering built-in joinery together with the rest of the fit-out

Bookshelves rarely stand alone. They sit against wall panelling, next to doors that need to clear a shelf end, and under ceilings with cornices or shadow gaps. Coordinating those items with one manufacturer removes a whole category of site argument about who is responsible for the junction.

If you are furnishing a villa or apartment project as a package, this is also where wall-mounted shelves and open display units are easiest to align with the cabinetry run: same board, same edge, same batch. Where a project needs made-to-measure dimensions rather than catalogue sizes, ask for custom/OEM production with a prototyping or sample stage before the full run.

Three questions that reveal supplier competence quickly

  • "What is the maximum span at this shelf thickness, and what load does that assume?" A factory that builds shelving has an answer; a trading desk will hesitate.
  • "Show me a production drawing from a comparable project with site tolerances resolved." You will learn how they handle the awkward cases.
  • "What ships in the crate for fixing and finishing?" Missing fixings and edge materials are how joinery jobs stall on site.

Frequently asked questions

How deep should open bookshelf shelves be?

Around 250–300 mm suits most books; deeper than that is usually wasted unless the shelf also carries boxes, records or display pieces. Set depth per zone rather than picking one figure for the whole wall.

What shelf spacing works for mixed collections?

Roughly 300 mm for standard fiction, taller bays of 350–400 mm for large-format or horizontally stacked volumes, and wider gaps at the top and bottom for objects. Adjustable shelving on pitched holes or a system with moveable supports lets you change the layout later.

Should open shelving be fixed to the wall?

Yes, in any project where children or guests are present, and in seismic or high-traffic commercial settings. Fixing detail depends on wall construction, so confirm what substrate is behind the lining before the unit arrives.

If your project needs made-to-measure open bookshelves coordinated with cabinetry, wall panelling and doors as one package, send us the drawings and we will quote against them — including sample boards, production drawings for sign-off and delivery terms stated in writing. Contact SANTERSON to start that review.