A backlit feature wall looks complete the day it is installed. It is judged years later, when a light section dims, a panel needs removing to reach a socket, or a spare part has to be matched to a finish that was specified eighteen months ago. That is why serious buyers treat Santerson Backlit Feature Walls as a system to be documented, not a decorative panel to be ordered. The questions below are the ones we recommend putting in writing before an order is confirmed.

What exactly is being specified on the product page

Our Media & TV Walls listing describes a configurable wall system: finish, layout and dimensions are set per project rather than chosen from a fixed size table. The same applies across the wider collection, from Santerson Full Height Media Walls to Santerson Integrated LED Media Units. Because the electrical part of a backlit wall is defined project by project, we ask buyers to confirm dimensions and lighting specification for each order in writing. If your architect has already set a driver location, a dimming protocol or a cable route, send it with the drawing instead of leaving it for the site stage.

Ask which parts are standard and which are project-specific

Configurable systems vary between projects, so the practical question is not whether a component exists but whether it belongs to your specification. We suggest confirming, item by item:

  • the panel substrate and finish you are being quoted, matched to the sample reference rather than to a photograph;
  • the light source, driver and any controller included in the quoted price, and where each of them sits once the wall is closed up;
  • which sections are demountable, and how they release, so wiring, the TV mount and any media cabinet behind the panels can be reached later;
  • the fixing method for your substrate — masonry, stud wall or an existing lined surface — because that decision is made at the factory, not on site.

A buyer who receives this list answered in writing has a specification to inspect against. A buyer who does not is comparing two different walls at handover and arguing about it afterwards.

Service scope after the container arrives

Our Installation & After-sales Support page sets out the stages we cover: on-site installation, inspection and snag resolution, warranty coverage, spare parts and replacement, and ongoing maintenance. Use those stage names as your checklist when you request a quotation, and ask us to state for each one what is included, what your local contractor handles, and where the boundary sits in your country specifically. Installation on a finished interior wall interacts with flooring, skirting, plasterboard and electrical first-fix, so the boundary line matters more than the slogan.

The page also quotes response and resolution aims. Treat published response times as figures to have confirmed for your project, in writing, before order — they depend on where the site is and who is doing the work, and we would rather agree that at quotation stage than discover it during a snag period.

Warranty terms worth pinning down

A backlit wall usually carries two warranties with different clocks: the joinery and finish, and the electrical components. Ask us to separate them in the order confirmation, and to state what evidence of installation is required for each to stand. Where a third party on your side runs the wiring or closes the wall up, that work should be documented before panels go on, because it is exactly the point where claims get disputed.

Spare parts: match them at order, not at failure

Ask which items are realistically available as spares after handover — light source, driver, controller, handles or opening mechanisms, and a panel in the exact finish for a future repair — and ask us to record the references on the same document that carries your dimensions. Panels are made to measure, so a replacement ordered two years later against a photograph is a risk you can remove for the cost of one line in a file.

How this fits a wider package order

Feature walls rarely arrive alone. Villas and hospitality projects that order wall systems from us usually also order cabinetry, wardrobes, doors, flooring and lighting, and the after-sales conversation becomes much easier when one supplier holds the specification for all of it. Under our one-stop solution scope, the same team handles material selection, product specification and production coordination, then hands you a single set of references to work from when something needs attention later. If lighting is integrated into shelving or display joinery as well — for example Santerson Illuminated Display Cabinet — specify the electrical requirements together, so drivers, cable runs and access points are resolved once instead of in three separate trades.

Send your drawing, a photograph of the wall, or a reference image with the dimensions you need, and we will confirm the specification and the after-sales scope against it before anything is produced. That single exchange is what turns "after-sales support" from a phrase on a page into something you can hold us to.