A grey modern kitchen with an LED-lit glass wine cabinet looks simple on a render: flat panel doors, one glowing glass tower, tall units housing ovens. In production it is one of the most coordination-heavy items in a villa or apartment fit-out, because cabinetry has to agree with appliance dimensions, stone worktops, electrical points, wall finishes and floor levels before a single panel is cut. The questions below are the ones worth putting to any supplier — including us — before an order is confirmed, written for project buyers, contractors and interior designers who carry the cost when something is specified wrong.

1. What exactly is being quoted: carcass, doors, or a complete kitchen?

Ask any supplier to state line by line what falls inside the price. A cabinet quotation may cover door fronts only, or carcasses plus doors plus worktops plus hardware, and the gap between those two numbers is substantial. Confirm in writing whether worktops, splashbacks, plinths, handles, lighting drivers and installation are included or excluded — exclusions are where budget overruns appear after award.

For our grey modern kitchen cabinets with LED glass wine cabinet, the specification covers cabinet bodies, doors and internal storage partitions, and matching hardware — hinges, drawer slide rails, support legs and connecting brackets — can be supplied on request. Panel dimensions, partition layout, panel colour and surface finish are set per project rather than chosen from fixed modules.

2. Who is producing the panels, and how is consistency controlled?

Grey flat panel doors look forgiving but expose every fault: a wave across a large matte door, a colour shift between batches, an edge banding line that catches light. Ask what board substrate is used, which surface treatment is applied, and how the supplier holds colour consistent across a multi-apartment order. If you are ordering more than one unit — several apartments, or a villa plus guest house — ask specifically how grey tone is kept identical across production batches, and request an approved physical sample door before mass production begins.

"Grey" is not a specification. Ask for the surface treatment by name — matte, high gloss, acrylic, lacquer, melamine, PVC or wood veneer — and judge a physical sample under site lighting, because grey reads very differently under warm LED downlights than in north-facing daylight. Where the project already has a colour reference from another trade, send that specification to the cabinet supplier instead of describing the tone in words.

Surface optionWhat to verify before ordering
Matte flat panelResistance to marks and ease of cleaning; whether a handleless or profile-pull edge detail is specified.
High glossHow surrounding light sources reflect in the door; visibility of edge banding on the return face; protection during site handling.
Wood veneer or wood effectGrain direction across a run of doors, and matching with adjacent joinery such as wardrobes or wall panelling.
Glass-fronted unitsFrame profile, glass type, internal shelving layout, and whether the interior is lit.

3. How is the glass wine cabinet built, and how is it lit?

The illuminated glass tower is the feature of this design and also where a specification error costs most to correct on site. Ask:

  • Which glass is specified for doors and side panels — clear, frosted or smoked — and at what thickness? Glazing changes how everything inside reads.
  • Where the LED runs, and whether it is warm or cool white. Our specification calls for built-in warm LED lighting in the glass display sections, which suits glassware and tableware better than a cold strip.
  • Where the driver sits and how it is reached after installation. A light that cannot be serviced without dismantling the cabinet becomes a maintenance liability for whoever inherits the building.
  • Whether shelf spacing suits bottles stored on their side, glasses hung, or both — agreed against your actual glassware, not assumed.
  • How heat is managed in an enclosed lit cabinet positioned beside ovens.

On this design the tall cabinet area reserves space for stacked double ovens, with glass display sections next to closed storage so everyday items stay out of sight. That combination only works if appliance cut-outs, ventilation gaps and the lighting circuit are drawn as one set.

4. Which appliances must be fixed before drawings are released?

Appliance selection is the most common cause of rework in custom cabinetry. Before production drawings go out, confirm the oven, microwave, refrigerator, wine conditioning unit and dishwasher you intend to install, and send the manufacturers' cut-out sheets to the cabinet supplier. If appliances are not selected — normal at concept stage — ask the supplier to design to standard cut-out dimensions and to record that decision in the drawing set, so later procurement does not silently break the layout.

5. What happens between drawings, factory and site?

Custom cabinetry fails most often at handover points: designer drawing to factory detail, factory to freight, freight to installation. Ask who owns each stage and who signs it off. Our cooperation steps run project brief and design proposal, then quotation and detail confirmation, then production, shipment and follow-up — with space layout planning and 3D visual renderings feeding the drawings before anything is cut. Within a turnkey furniture and building materials package the same team covers material selection, product specification, manufacturing quality control, project management and site coordination through to installation and handover.

On freight, ask what is actually provided: packing method, container loading plan, commercial invoice and packing list, certificates of origin, customs documentation, and who acts as importer of record. We arrange sea, air and rail freight with door-to-door delivery, but duties, Incoterms and delivery terms are agreed per project and destination rather than taken for granted.

6. What is fitted, inspected and supported afterwards?

A complete kitchen can still fail on site: doors out of alignment, chipped glass, a lighting circuit that does not work. Ask who installs, whether inspection and a snag list are in scope, what warranty applies separately to cabinet bodies, hardware and lighting, and how replacement parts — one hinge, one drawer runner, one door panel — are supplied years after the order closed. Hardware wears before panels do, so spare-part availability usually matters more than buyers expect.

7. How does this kitchen sit with the rest of the fit-out?

Ordering cabinetry alone means matching grey doors, stone, flooring and wall finishes to whatever else is already on site, usually imperfectly. Where scope allows, group the kitchen with other interior fixtures — custom built-in kitchen cabinets for hotel and apartment work, wardrobes and storage, engineered wood flooring, wall panelling and ceiling finishes. One supplier holding those specifications keeps colour, edge detail and levels consistent between rooms, and gives you one production schedule instead of six competing ones.

Before signing: a complete grey kitchen cabinet order should come with signed dimension drawings, appliance cut-out sheets, an approved physical sample door, a written inclusions list, the glazing and lighting specification for the wine cabinet, packing and shipping terms, and a stated warranty and spare-parts route. If any of these are missing from a quotation, it is not comparable with another supplier's.

If you are specifying this kitchen for a villa, apartment or boutique hotel project, send us the drawings or floor plan and we will respond with a specification and quotation structured around the questions above — including the grey modern kitchen cabinets with LED glass wine cabinet configuration, custom sizes and finish options.